Search Documents

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By M. J. H. Tonkins, C. C. Crosson, G. Paterson

The development of drilling and blasting practice at Palabora Mining Company Limited by c. C. CROSSON, Pr. Eng., A.C.S.M. (Hons), BASe. (Min. Eng.) Toronto, M.!.M.M. (Member), M. J. H. TONKING, Pr. Eng., A.C.S.M., BASe. (Min. Eng.) Toronto, M.I.M.M. (Member), and G. PATERSON, B.Se. (Min. Eng.) Glasgow, M.!.M.M. (Visitor) Open-pit drilling and blasting practice at the Palabora Mining Company Limited is described, with particular reference to the development of aluminized slurry explosives. Rotary drilling of primary drill holes, drilling patterns, and blasting techniques for use with slurry explosives are described.

Jan 2, 1976

By Helena Byrdziak

KGHM Polska Miedz S.A. is a significant European copper producer with production of 447,000 mtpy, operating three underground mines and three smelters. The company has been involved for years in environmental activity, which was stimulated not only by the company itself, but by the development of environmental regulations as well. The first set of regulations, concerning water protection, was' established in Poland' in 1974, while a comprehensive environmental law was passed in 1980. This law in general requires industry to submit all data of environmental significance to the local authorities. Based on this data, they establish limits concerning emissions into the air, water and ground, the amount of wastes produced and the means of their disposal. A company has to pay fees for each tonne of emitted substances and stored wastes. When the emission of a substance exceeds the limit, the company has to pay a penalty which is about ten times higher than the fees. This approach in general is effective because it forces companies toward: reduction of their emissions. The problem is that the law is constantly subject to change and is becoming not only more restrictive but is involving more and more bureaucracy.

Jan 1, 1999

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986

By G. E. Cole

"Amongst the mineral products of Canada gold holds the second place in value of yearly output. . . . . .The production of gold has increased steadily during the past six years and has somewhat more than doubled in that time. For the past four years Canada has been third among the gold producing countries of the world, surpassed only by the Union of South Africa, and the United States of America," and now yields somewhat more than 9 per cent of the annual output of the world."-"The Gold Situation in Canada". Bulletin of Development Branch, Canadian Pacific Railway. The history of gold mining in Canada is comparatively modern and does not take one further back than the late 'fifties of the 19th century. If the efforts of the early explorers in Canada were expended in "seeking with equal ardour, proselytes and gold", history fails of any record of their success in the search for the precious metal. As early as 1849 not a few Canadians travelled from the east by land and water to the Californian goldfields. In the then settled part of Canadathe east-people were alive to the value of any mineral discovery; but the west, owing to its remoteness and to there being no ready means of communication, was virtually isolated from the east.

Jan 1, 1927

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006

By Ritchie IC

Spiral separators have been used to treat heavy mineral sands in Australia for some thirty-five years. They were used as the primary treatment method until the advent of the Reichert cone, which largely replaced them, due to its compact design and relative ease of operation. Spirals continued-to be used as the final cleaning stage before dry separation of the heavy minerals as they remained the most efficient separator for this purpose.

Jan 1, 1986

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Mutton B. K

Hilton Mine is being developed as an integrated component of the Mount Isa operation, to achieve continuity of silver/lead/zinc production well into the next century. The mine has a chequered history from its discovery in 1947 through several periods of intense development activity, each of which has been curtailed due to the further development of the Isa Mine operation. This era has now passed; to sustain increased production rates at Mount Isa, there is a requirement for Hilton ore in 1989. The decision was made in 1983 to accelerate the programme of Hilton development by installing skip hoisting facilities in the main service shaft (P49), to facilitate the development of the mine to pre-production status. The Hilton development plan provides for the mining of selected orebodies, a broadening of the underground exploration drilling programme, and the establishment of significant mine infrastructure. Several technical challenges have been identified as important. The Hilton orebodies, although occurring in the same rock type as Isa Mine, are more faulted, jointed and intersected by intrusive dykes. The ore is more variable in terms of ore continuity, boundaries, grade and metal distribution and the mineralogy more complex. As a consequence the development of this project consists of a co-ordinated programme of mine exploration and development, rock mechanics investigations and metallurgical research and development work. Production will commence in 1986 at a rate of 1000 t/day using mechanized cut and fill techniques. It is planned to introduce sublevel open stoping and by 1996/97 the production rate will be 2.5 million t/yr.

Jan 1, 1986

By White PJ, Worrad C

The Hunter Valley Coal Preparation Plant and associated materials handling facilities commenced operation in mid 1982. The new plant and coal handling system were designed to integrate with existing mining and preparation plant operations, but also to be flexible to future mining and marketing developments. The system includes: raw coal stockpiles, a 900 tph dense medium/water washing cyclone preparation plant, clean coal stockpiles, a 7.8 km overland conveyor, large finished product stockpiles and a high capacity train loading plant.The plant's development is described with reference to the original planning objectives. Features aimed at providing operational flexibility and performance are emphasised, including the use of; automated stackers and reclaimers, modular plant, distributed PLC control, a single flight overland conveyor, a network of automatic samplers and blending options to assist quality control.Details are also provided of an innovative technique for control of reclaimer rail track forces, stacker and reclaimer anti-collision systems and the use of DC injection braking.

Jan 1, 1985

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1985 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 5, 1978

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1983 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 1, 1979

The origins of instrument application in the Mineral Industry are discussed. Development of measurement techniques pertinent to the industry is described as is the early application of mini-computers. The current application of microprocessor based equipment and the benefits obtained from this range of equipment are discussed. A speculative opinion as to what future instrument development may offer the industry is outlined.

Jan 1, 1985

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world's centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971