Search Documents

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation' it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,' not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By W. D. Roberts

INTERGRANULAR corrosion of metals and alloys has been extensively investigated and the current conclusions are summarized in the Symposium on Stress-Corrosion Cracking of Metals.' It appears, however, that the relative importance of the various factors involved in the mechanism is still obscure. Several recent, independent studies, in combination with available X ray data op preferred orientation, indicate that there may be a direct correlation between relative orientation of contiguous grains and susceptibility to intergranular corrosion. The object of the present note is to show the nature

Jan 1, 1951

By L. K. Jetter, C. J. McHargue

DEVELOPMENT of preferred orientation in uranium is of interest because of the strongly anisotropic properties of the orthorhombic crystal structure. Harris&apos; reported inverse pole figures for rolled uranium rods which showed <010> and <410>* to be parallel to the rolling direction after On 0.19-in. spherical X-ray diffraction specimens taken from the center of the middle section of each rod, pole distribution data were obtained by the spectrometric method described previously.4 The specimen was rotated rapidly about the axis coinciding with the rod axis in order that a large number of grains could be scanned and was rotated slowly about an axis perpendicular to the rod axis. The variation in the diffracted X-ray intensity was recorded as a function of the latter motion (angle 4). Fiber-axis distribution charts (inverse pole figures) were prepared by the method described by Setter, McHargue, and Williams." After having been corrected for background radiation, the pole distribution data (I vs ?) were normalized. A normalizing factor for each plane has been shown to be Iranaom = f I sin 4 ? 4 and was obtained by graphical integration from the data for that plane plotted as I sin ? vs ?. The axis-distribution charts deduced from the normalized pole densities are shown in Figs. 1 to 3. On these charts, the contours indicate angular positions of equal normalized axis density,

Jan 1, 1958

By J. H. Keeler

AN alloy of zirconium containing 18 atomic pct Cb was found to be body-centered-cubic and readily deformable at room temperature. The behavior of this alloy provided an opportunity to determine if

Jan 1, 1957

By J. W. Fredrickson

VERY little information is available in the literature concerning the solubility of magnesium in titanium. Aust and Pidgeon&apos; report the solubility of titanium in magnesium to be 0.0025 pct at 650°C and 0.015 pct at 850°C. X-ray diffraction studies failed to detect any evidence of solid solubility. Based on the fact that the addition of titanium to magnesium increases the c/a ratio of magnesium, Busk&apos; suggested that the Mg-Ti system, like the Mg-Zr, is a peritectic. Eisenreich- eported the solubility of titanium in magnesium to be 0.003 pct at 655°C and 0.064 pct at 760°C. Removal of hydrogen from the melt increased the solubility of titanium to 0.115 pct at 800°C. Eisenreich proposes a peritectic-type diagram for the high magnesium side of the system. Recent work&apos; with Ti-Mg diffusion couples indicate that the solid solubility of titanium in magnesium is extremely small and that there is limited solid solubility of magnesium in titanium. Experimental work on the Ti-Mg system is complicated by the fact that the boiling point of magnesium is considerably below the melting point of titanium. Consequently, the usual alloying methods are impractical. Alloying was accomplished in this investigation by sheath-rolling compressed compacts." The alloys were made from titanium sponge and high purity magnesium. Chemical analysis of the sponge showed 0.04 pct Mg, <0.005 pct Al, <0.001 pct Cu, 0.05 pct Fe, 0.022 pct Mn, <0.0025 pct Ni, 0.007 pct Si, <0.005 pct V, and <0.01 pct Zn. All heat treating was conducted in a protective atmosphere by encapsulating the specimens in fused silica ampules under a partial pressure of helium. Equilibrium was achieved by holding the specimens at temperature for periods of 24 to 120 hr. The alloys were hot rolled, cold rolled, and annealed prior to solution heat treatment. Fig. 1 shows the constitutional diagram obtained for the Ti-Mg system up to 1.5 pct Mg. Oxygen was known to be present in the alloys; therefore, it is necessary to consider the alloys as ternary rather than binary and the diagram should be viewed as a plot of a section through the Ti-Mg-0 system. Other investigatorso have shown that the addition of oxy- gen to titanium stabilizes the a phase. The data presented in Fig. 1 indicate that the addition of magnesium to titanium tends to stabilize the p phase. Armour Research Foundation7 has shown that the addition of magnesium to zirconium lowers the a transus and is classified as a p stabilizer in that system. Magnesium is soluble in solid titanium to the extent of at least 1.5 pct in both the a and /3 phases. No intermetallic compounds or magnesium-rich phases were observed either by light microscopy or X-ray diffraction. However, this does not negate the possibility that such phases exist at higher alloy concentrations.

Jan 1, 1956

By Dilip K. Das, Douglas T. Pitman

ONE of the major uses of barium in metallic form is as a getter material in vacuum tubes. Because of the high chemical reactivity of the metal, Ba-Al alloys are extensively used. Numerous methods for the preparation of Ba-Al alloys have been published, a few of which1-4 are cited here. Most of these methods were found to be quite elaborate, involving the reduction of BaO, and not too well adapted for the close control of the final composition of small amounts of alloys prepared for laboratory use. A simple laboratory method for the preparation of Ba-A1 alloys in small batches starting from pure metals was devised, so that it was possible to control the desired compositions to within 1 pct. The pertinent features of the alloy system Ba-Al5 are 1) an intermediate compound BaAl, with the melting point of 1050°C, and 2) a eutectic between aluminum and BaAl4 at 98 pct Al. The accompanying sketch shows the experimental arrangement for the preparation of the alloys. Weighed amounts of aluminum and barium were placed in an alumina and a stainless steel crucible, respectively. According to the supplier&apos;s specification, the purity of the metals used in the alloys is as follows: a) aluminum rods—99.9 pct Al, and b) barium rods—99.5 pct Ba. The stainless steel crucible, tapered at the bottom and having a 1/16 in. diam hole, rested on top of the alumina crucible. The assembly was placed inside a graphite sleeve which rested on a refractory platform. The platform moved the assembly up and down through the field of a radio frequency coil. A glass bell jar was placed between the crucible assembly and the radio frequency coil to maintain a steady flow of helium around the melt. A small window was cut out on the wall of the alumina crucible to observe the progress of the re- action and to record the temperature with an optical pyrometer. The platform was first raised high enough to move the barium out of the radio frequency coil field in order to allow only the aluminum to melt. The assembly was then lowered so that the barium began to melt and flow out through the small orifice into the molten aluminum. In order to keep the violence of the exothermic reaction under control, the rate of flow of barium was carefully regulated by raising or lowering the crucible assembly. All the samples prepared by this technique were examined by a Norelco X-ray diffractometer using CuKa radiation, The diffraction specimens were prepared by placing the finely powdered samples in flat specimen holders. The Ba-Al alloys prepared with a high barium content were found to consist mainly of BaAl4. The structure of BaAl4 has previously been reported by Alberti and Andress.8 They found that BaAl4 was body-centered-tetragonal with an a0 = b0 = 4.530Å and c0 = 11.14Å. An alloy whose composition was found by chemical analysis to be almost 100 pct BaA1, was used to determine the relative intensities. The d-spacings were obtained from the same alloy to which a small amount of tungsten had been added as a calibrating material. Accurate values for a, and c, were calculated according to the method proposed by Taylor and Floyd.&apos; The calculated values are: a, = b, = 4.566Å and c0 = 11.250Å. The measured d-values for BaAl4 are shown in Table I along with relative peak intensities above background and hkl indices. Acknowledgment The authors are grateful to L. J. Cronin, the head of the Techniques Dept., for suggesting the problem and for his constant interest. References 1Froges and Camargue: German Patent No. 809107, 1951. French Patent No. 935324, 1949. 2E. Bonnier: Annales de physique, 1953, vol. 8, pp. 259-312. 3M. Orman and E. Zemhela: Prac Institute of Metals; 1952, vol. 4, pp. 437-445. 4E. Fujita and H. Yokomizo: Reports Gov. Chemical Industrial Research Institute, Tokyo, 1952, vol. 47, pp. 291-297. 5E. Alberti: Ztsch. fur Metallkunde, 1934, vol. 26, p. 6. 6E Alberti and K. R. Andress: Ztsch. fur Metallkunde, 1935, vol. 27, p. 126. 7 A. Tnslor and R. W. Floyd: Acta Crystallographica, 1950, vol. 3, p. 285.

Jan 1, 1958

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function&apos; used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail&apos; and the results are simple and generally applicable. &apos;The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy&apos;s law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

By C. G. Dunn

THE present note, which was given in the form of a Research in Progress item,&apos; traces the origin of secondary recrystallization grains produced on annealing a cold rolled bicrystal specimen. The investigation began with the realization that a recently acquired conception for the origin of secondary grains produced on annealing cold rolled single-crystal specimens might require modifications for the case of polycrystalline materials. The stated conception2,3 begins with several conditions to be met by primary recrystallization: 1—a primary re-crystallization structure to consist of many small primaries and relatively few large primaries (diam- eters two or three times the average); 2—a primary recrystallization texture to consist of one strong preferred orientation or component and one or more weak components; and 3—a primary recrystalliza-tion structure-texture combination with some of the large primaries belonging to the weak components of the texture. When these conditions occur, some of the large primaries from the weak components of the texture

Jan 1, 1955

By H. H. Rachford, and J. D. Rice

The effectiveness of digital computing machines in making technical calculations depends on how well the work is arranged to utilize the capability of the machines. This note presents a particularly useful way of calculating hydrocarbon vapor-li.quid equilibrium in the flash vaporization (or condensation) system. The method is well suited to sequence-controlled computing equipment. It is not limited to equilibrium calculations and may be used for solution of most implicit equations in one variable. INTRODUCTION There is increasing interest in the use of electronic digital computers in research and engineering calculations. This is a fortunate and inevitable trend in view of both the increasingly extensive numerical work which is becoming a routine part of many daily production operations and growing demand for the overwhelming amounts of calculations required by newly developed numerical methods for solving heretofore unsolved problems. Machines are in many ways ideally suited to the task but of necessity present certain difficulties. for a particular poblem to be solved must often be formulated quite differently from the way it would be arranged for manual solution. This is done in order to take advantage of the inherent speed and precision of electronic computers and at the same time to limit the need for number storage to the capacity of the machine. Therefore, this note is submitted to present a general and quite powerful method of finding solutions of the frequently encountered implicit equation: F(x,y1,y2,...ya)=0.......(1) where the root, x, is to be found for a given set of y1, ... yn.. The procedure is well suited for use with computing machines, for it usually requires but little storage or programming beyond that necessary to evaluate F. HYDROCARBON EQUILIBRIUM The method is described in terms of the problem it was designed to solve, i.e., the calculation of hydrocarbon vapor-liquid equilibrium in flash vaporization. Given the composition of a hydrocarbon mixture and appropriate values of the equilibrium ratios K, to find the phase ratio and compositions in a closed system: let z, be the mol fraction of the i-th component in the mixture. If K, is the ratio yl/xl, where y, and x,

Jan 1, 1952

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By E. R. Morgan, J. C. Shyne, V. F. Zackay

NITROGEN used as an alloying element in steel has received increased attention in recent years. Its merit as an austenite stabilizer and hot strengthener has long been recojinized, particularly by European investigators.&apos; Recent work&apos; indicates that nitrogen contents of 1/2 pet or more allow the addition of several percent of ferrite-forming hot strengtheners, such as molybdenum, without subsequent austenite decomposition at elevated temperatures. The room temperature properties of such alloys are characterized by high yield and tensile strengths with excellent ductility, even after cold working, as shown in Tables I and 11. The 1350°F creep-rupture properties of Cr-Mn-Mo-N steels are comparable to those of commercial alloys such as Timken&apos;s 16-25-6, containing 16 pct Cr, 25 pct Ni, and 6 pct Mo, as shown in Table 111. Cr-Mn steel containing 1/2 pet N must be made under pressure if ingot gassing is to be avoided. However, there are difficulties attendant to this practice. Pressure melting restricts the ingot size, and the equipment required is costlier and more complicated than comparable air melting facilities. An effort was made, therefore, to determine more economical methods of adding nitrogen. The pressures generated in centrifugal casting usually range from 5 to 10 atm and are sufficient to prevent the gassing of high nitrogen Cr-Mn steels. A centrifugal casting was made of an alloy containing 16 pct Cr, 18 pct Mn, 2 pct Mo, and 0.73 pct N. A risk, 8 in. diam and 11/2 in. thick, was cast at 1000 rpm. It has been calculated that a pressure of 9 atm was developed at the periphery of the disk at this speed. Metallographic inspection of specimens taken from the disk revealed no gas holes or other defects. The elevated temperature properties of radial and circumferential specimens taken from this casting are given in Table IV. The creep-rupture life of this cast nickel-free austenitic steel was equivalent to that of the wrought Cr-Mn-Mo-N steels. Although centrifugal casting appears to lend itself to the manufacture of high nitrogen austenitic steels, its applicability is limited to relatively small sizes. A process applicable to the production of large ingots of high nitrogen steels is suggested by low carbon rimming steel practice. Gas holes formed during ingot solidification are not detrimental so long as they weld shut during hot rolling. An economic advantage of gassing ingots is the increased ingot-to-slab yield, especially if the ingots are mechanically capped. Also, it is probable that higher nitrogen levels can be achieved with mechanically capped ingots than with hot-topped ingots. A series of gassy heats was made under both atmospheric and higher pressures, as indicated in Table V. Several of the air melted ingots were mechanically capped by chilling the molten ingot tops with a steel plate. The ingots were allowed to freeze in steel molds without hot-tops unless otherwise indicated. A comparison of Table 111 with Table V shows no significant difference in the creep-rupture properties of the gassy and the nongassy ingots after hot work- ing nor between the gassy ingots produced under different conditions. References 1 F. Rapatz: Application of Stainless and Heat Resisting Steels Alloyed with Nitrogen. Sinhl and Eisen ( 1941) 61, pp. 1073-1078. &apos;V. I?. Zackay, J. F. Carlson, and P. L. Jackson: High Nitrogen Austenltlc Cr-Mn Steels. Trans. ASM 119551 48, PP. 509-523.

Jan 1, 1957

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues&apos; have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.&apos; Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer&apos;s value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,&apos; analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By Mary Barrett, Walter Rose

INTRODUCTION The conventional way to program reservoir problems* for solution on the electric analyzer1 is one which concentrates the block units towards the inner radius of the prototype system being represented by the analog model. This is achieved by the device of considering block units of equal value radial resistance, leading to the consequences: (1) the ratio of the external to the internal radius of each block unit is a constant (i.e. r1/ri-l = constant a); (2) the external radius of the nth block unit is equal to the innermost radius of the system times the constant a raised to the nth power: (3) the capacitance of the block units increase by a factor of a2 going out radially from the innermost to the outermost boundaries of the system; (4) given n block units in the radial direction, the capacitance ratio of the outermost to the innermost block unit is a (2n-2); and (5) the vertical resistance of the block units decrease by a factor of a going out radially from the innermost to the outermost boundaries of the system, such that the ratio of the maximum to minimum vertical resistance is also given by the factor a(2n-2) PRESENT PROGRAMMING METHOD While this conventional way of programming problems is quite adequate for routine uses of the electric analyzer, it leads to difficulties in those cases where the inner radius of the prototype system (e.g., the well-bore) is small compared to the external radius (e.g.. the external reservoir boundary). To handle such a case by the conventional method would require either that a large value be selected for the constant a or that a large number n, of radial block units be chosen. In consequence, the capacitance and vertical resistance ratios become impossibly large, as will be evident from the relations given above. In any event, the size of the smallest and largest capacitors will always be limited by the size of commercially available components, and the analyzer itself will determine how many mesh points are available for radial block units. For example, it can be shown that if the maximum capacitance ratio which can be electrically handled is a factor of l04, the maximum external radius of the system which can be considered (assuming an internal wellbore radius of 0.25 ft is: It is thus seen that in direct consequence of having the inner wellbore radius small compared to the external radius, models extending beyond 30 to 40 ft are not possible when the capacitance ratio is limited to l04. (NB. A value of 10-9 farads can perhaps be taken as the minimum electrical capacitance possible if corrections for the capacitance of the lead wires are to be avoided. Values greater than 10-5 farads would require the use of unstable and inaccurate electrolytic capacitors). On the other hand, models extending out to 500 to 5,000 ft may be desired in single-well problems, and hence the need for a revised method of problem programming. * REVISED PROGRAMMING METHOD The revised method of programming is one which attempts to retain the desirable features of the conventional method (viz. concentration of block units towards the inner boundary, simplicity in computation, etc.) without having as a consequence that impossible capacitance and vertical resistance ratios will be required. Other advantages will also be achieved by the revised

Jan 1, 1957

By Rikuro Otsuka

TITANIUM is attacked slowly by hydrochloric acid," and corrosion rates decrease with time of exposure.&apos; This behavior is due to the formation

Jan 1, 1958

By A. J. Goss, M. Tanenbaum, W. G. Pfann

THE purification of two metals, antimony and tin, by zone refining is described, and a reciprocating method of passing molten zones through a straight ingot, which effects a considerable economy of time and apparatus, is discussed. Antimony has been used extensively as a doping agent in germanium and silicon. More recently, it has become important in the preparation of new semiconducting compounds such as InSb, GaSb, and AlSb. High purity is especially necessary in this latter use, since the antimony may comprise as much as 80 pct by weight of the compound. Antimony is generally available in a commercial form of about 99.8 pct purity. Column 1 of Table I is a typical emission spectra analysis of commercially available 99.8 pct antimony. Zone refining has been quite successful in increasing the purity of such samples. Columns 2 to 4 of Table I are analyses of an ingot of the antimony of column 1 after the passage of seven molten zones in an atmosphere of nitrogen. The ingot length was 9 1/2 in.; the mean zone length was 2 in.; convection was the only means of stirring. The column headings are sample locations in inches from the leading end of the ingot. The results illustrate both the merit and a limitation of zone refining. It is seen that four of the five impurities—nickel, arsenic, lead,

Jan 1, 1955

By W. M. Fox, D. P. Detwiler

IN the course of research on semiconducting inter-metallic compounds, it became necessary to obtain gallium metal of greater purity that that available commercially. Several methods were considered for further purification, including acid leaching,&apos; fractional crystallization,&apos; and zone-refining.3-5 The method of fractional crystallization was discarded as being equivalent to zone-refining in purification but inefficient in material and time. Both acid leaching and zone-refining were tried, and the method finally adopted is a combination of the two. The acid leaching technique has been reported&apos; to produce gallium in which no impurities are detectable spectroscopically. Although this method is very effective in removing oxides and surface contaminants, semiconducting material made of gallium subjected only to leaching indicated little reduction in the concentration of metallic impurities. Zone-refining, however, appears very effective in removing trace metallic impurities, but comparatively ineffective in removing the surface oxide film. Consequently, the method evolved consists of acid leaching to thoroughly clean the surface, followed by zone-refining to remove metallic impurities. The low melting point and relatively high thermal conductivity of gallium introduce some difficulty in maintaining frozen and molten zones in zone-refining. To accomplish this, it is found necessary to reduce the effective ambient temperature by circulating ice water in coils about the regions that are to be kept frozen, while heat is supplied to the molten regions by resistance coils. The power supplied to the heating coils is regulated by a constant-voltage transformer and a variable autotransformer. Both heating and cooling coils are mounted on a transite base. The gallium ingot is held in a closed pyrex tube sliding inside the heating and cooling coils, the reciprocating method of Tanenbaum et al. being employed to move the molten zones through the ingot at a rate of 2 in. per hr. This apparatus is shown in Fig. 1. The results of a spectroscopic analysis f a zone-refined ingot, as well as of the material as-received and after acid leaching, are shown in Table I. The ingot was 32 cm in length, and received 37 molten-zone passes, the molten zone being about 4 cm long. The only impurity found was lead, the following elements being reported also as checked but not found in the pure material: Al, Sb, As, Ba, Be, Bi, B, Cd, Ca, Cr, Co, Cb, Cu, Ge, Au, Fe, Mg, Mn, Mo, Ni, Pt, Si, Ag, Na, Sr, Sn, Te, Ti, W, V, Zn, and Zr. There thus appears no indication of pickup of Al, Mg, or Si from the pyrex boat as reported by Zimmerman&apos; in his fractional crystallization. Thus it appears that definite removal of lead from gallium occurs during the zone-refining process. It also may be concluded that a more sensitive analytical procedure than spectroscopy is required to evaluate quantitatively the purity of zone-refined metals. One such procedure which is proposed for use in the near future is the measurement of very low temperature resistivity. Although this will not identify the impurities present, it offers a very sensitive check of total impurity. Acknowledgment This work was supported by the Air Research and Development Command, United States Air Force.

Jan 1, 1956

By P. A. Beck

In the course of work on grain growth in high purity aluminum a simple optical method was developed for detecting the presence or absence of preferred orientation in annealed specimens. The specimens were prepared by grinding, polishing and "deep etching." The etching reagent used for high purity aluminum has been described.* The resulting etch pits produced selective

Jan 1, 1949

By William T. Barrett, James E. Lawver, James L. Wright

One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.&apos; Brown measures the radial component of the field intensity 1/2 in. from the drum surface and fits a Fourier series in the angle about the drum axis (Fig. 1). Once the coefficients of the series are known, it is then possible to calculate the values of the radial and angular

Jan 1, 1971

By C. W. Spencer, K. A. Semlak, F. N. Rhines

IN an effort to obtain a better understanding of sintering in the presence of a liquid phase, it was decided to study the rate of capillary rise of a relatively low melting liquid metal in a higher melting metal powder compact. By assuming that the metal powder compact consists of a great number of parallel capillary tubes and that the flow of liquid

Jan 1, 1958