Search Documents

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By T. B. Szwilski, R. D. Begley

Status of ISO 14000 standards. The ISO 14000 are voluntary international standards providing a frame-work that allows a company to integrate an effective environmental-management system (EMS) into its operations. The purpose of an EMS is to provide a systematic procedure to identify the environmental aspects of a company's activities, evaluate any significant impacts and use the information to set objectives and targets toward continuous improvement of the company's environmental compliance and performance. In addition to the specifications for certification, ISO 14000 can be used as a guide to develop an effective environmental-management system or for self-declaration. The International Organization for Standardization (ISO) is a worldwide federation founded in 1947 to promote the development of international manufacturing, trade and communication standards. The organization is now represented in 118 countries, with the American National Standards Institute (ANSI) representing the United States. The principal goals of the ISO is "to promote the development of standardization and related ac¬tivities in the world with a view toward facilitating the international exchange of goods and services and to develop cooperation in the sphere of intellectual, scientific, technological and economic activity." ISO develops standards with input from government and industry. Because the standards are voluntary, there are no legal requirements to pressure countries to adopt them. However, many governments, industries and US agencies are adopting the ISO standards as a requirement for business trans¬actions, thereby, compelling suppliers to adopt ISO standards. These business and market forces, which are likely to be strategic business issues in the 21st century global marketplace, are imposing the need to develop a systematic approach to environmental management. The ISO 14000 series evolved from a United Nations Conference on the Human Environment in 1972. It includes a broad range of elements: the basic environmental management system, environmental auditing criteria for internal and external auditors, criteria for environmental performance evaluation (EPE), environmental labeling criteria and life-cycle assessment methodologies. The standards comprise two categories: organization evaluation standards and product oriented standards (Table 1). The ISO 14001 specifications contain the requirements for developing an environmental-management system that may be objectively audited for certification. The ISO 14004 standard provides guidance on interpreting the ISO 14000 specifications for the development and implementation of the EMS and for coordination with the management system of the company. On Sept. 1, 1996, the American National Standards Institute (ANSI) and the Registrar Accreditation Board (RAB) signed a formal agreement to create a new entity called the National Accreditation Program (NAP). To obtain certification, a company must fulfill the requirements outlined in ISO 14001. It is required that "a third party give written assurance that a company's EMS meets all the requirements of ISO 14001." Preparing for ISO 14000 can include subscribing to voluntary environmental initiatives; learning from ISO 9000 quality-management experiences; and utilizing information from recognized training courses, publications and numerous Internet resources. Once committed to an EMS, the management should provide sufficient resources to achieve continuous environmental-performance improvement, as outlined in an environmental policy. A thorny issue now being debated concerns the potential liabilities of documenting the environmental performance of a company. General impact of the ISO 14000 EMS standards. With increasing stakeholder awareness, costly end-of-pipe pollution-control approaches and the success of ISO 9000 quality-management standards, the ISO 14000 EMS standards are being adopted by companies and governments worldwide. The United States and Canada have well-established programs. In Europe, countries differ but are firmly committed toward environmental-management standards (BS 7750, EMAS and ISO 14000). The Department of Environmental Protec¬tion of the State of Pennsylvania is using ISO 14000 as a vehicle to develop a closer working relationship with industry, and it is anticipated that this policy will eventually lead to fewer environmental site inspections for those companies with ISO 14001 certification. The Depart-

Jan 1, 1999

By Y. Akin, M. S. Celik, T. Batar, F. Arslan

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, the boron minerals colemanite, ulexite and borax undergo decrepitation, shrinkage and expansion, respectively, upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot-plant studies conducted in our laboratories on the calcination of boron minerals are briefly reviewed and their implications to commercial operations are discussed.

Jan 1, 1999

By J. E. Flinn, J. M. Welch, R. L. Miller

Introduction Two samples of an iron-enriched basalt (IEB)-a silicate-based fused-cast ceramic waste form-containing components that simulate Three Mile Island Unit 2 core debris were tested for uranium recovery (Miller et al., 1984). This material is highly refractory towards leaching by ground water. The uranium content is high (15.1%) and the U-235 content (2.57%, only

Jan 1, 1986

By L. A. Ruth

Introduction The US Department of Energy's Office of Fossil Energy has begun a new approach for developing the ultra-clean energy plants. This approach will allow the nation to continue to use low-cost fossil fuel feedstocks during the early decades of the 21st century. The new approach is called Vision 21. The overall goal is to effectively eliminate, at competitive costs, environmental concerns associated with the use of fossil fuels for producing electricity and transportation fuels. Vision 21 is based on the following three premises: •The nation will need to rely on fossil fuels for a major share of our energy needs well into the 21st century. •It makes good sense to rely on a diverse mix of energy resources, including coal, gas,

Jan 1, 2003

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 1, 1986

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

By M. Liu

The use of surfactants shows great potential for the removal of hydrophobic organics from soils by in-situ washing techniques. Lab-scale soil washing experiments were performed using sodium dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that the solubility of anthracene increases linearly with an increase in SDS concentration above the critical micellar concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1993

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

Introduction Of the techniques reported for cyanide removal from effluents, alkaline chlorination is the most common (Fisher and Wasser, 1969; Reidt, 1969). Shortcomings with this technique are the high reagent costs, chlorine contamination, and potential formation of cyanogen chloride. Chemical oxidation methods are also not suitable to remove cyanide from effluents containing sulphides in suspension, such as flotation tailings. An inexpensive method for removing cyanide, combined cyanide and related species from waste waters has been developed in Inco laboratories. The method is based on the use of sulfur dioxide (or a sulfite), lime, and air as the reagents. The decomposition reactions of cyanide, combined cyanide, and related species are catalyzed by copper in solution. Complete removal of cyanide species, most of which are oxidized to cyanate, is obtained by treating copper containing cyanide effluents with sulfur dioxide-air mistures while maintaining the pH between 6 and 10 with addition of lime. The new approach can also be applied to selective destruction of cyanide and combined cyanide in effluents containing sulphides in suspension, such as pyrrhotite. Again, a sufficient amount of dissolved copper must be present or added. Metals and precious metals present in the effluents are recovered as hydroxides by adjusting the pH of the treated effluents to about 9-10. Using the new method, the anionic species are removed in the following order: Free CN- > Complex CN- > Thiocyanate The above removal sequence is unusual as oxidants such as chlorine and ozone oxidize thiocyanate preferentially over the combined cyanide.

Jan 1, 1985

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By Whang K, Choi H

A study of flocculation of ultra-fine coal particles by ultrasonic waves was investigated on a laboratory scale.The coal suspension was dilute, with low ionic strength, and at pH 6·2.When a stationary sonic wave is set up in a solution containing suspended coal particles, it is believed that high and low pressure regions are alternately established at the half wave-length of the sonic wave and this resultsin the migration of coal particles towards the low pressure regions.As expected the flocculation is more effective as to frequency and the power of the ultrasonic waves is increased.The shape and size of the test equipment are also important variables.

Jan 1, 1977

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

KIeeman (1968) described practice in the Mount Hebbard dump concentrator, Broken Hill, N.S.W. The purpose of this note is to give data on flotation pulp chemistry in the plant for comparison with results of Woodcock and Jones (1970a, 1970b).Ten chemical parameters were measured at ten points in the circuit using the techniques of Woodcock and Jones (1970a, 1970b). Fig. 1 shows a condensed time plot of some continuous measurements in conditioner overflow and rougher feed. Fig. 2 shows average values of selected parameters at the start and end of each of the three rougher flotation stages.DISCUSSIONpH and redox potentiaIsFig. 1 shows that pH and Eh were relatively constant at the start of sulphide lead flotation. There was a fairly steady increase in pH throughout the circuit (Fig. 2), but flotation was always conducted in a slightly acid pulp in spite of the large amount of alkaline reagents added. Eh values became more positive as the pulp progressed through the circuit (Fig. 2) in accord with results elsewhere.

Jan 1, 1973