Search Documents

By Eugene A. Hickok

Seismic surveys utilizing the MD-1 have been performed by Geophysical Specialties Company since 1957 in many parts of the, U. S. and Canada and in several foreign countries. These surveys have proven the refraction seismic technique to be applicable to a wide variety of engineering problems. The best known applications of the instrument have been in the, construction industry, where it is used for the delineation of material and mineral deposits and for bedrock depth determinations. Fast on-the-site depth determinations give reliable subsurface' information even in boulder-strewn soils. A widely publicized use of the MD-1 is to make rippability studies in which the instrument is used to determine the seismic velocity of the materials to be excavated. By use of special tables which correlate rippability with seismic velocities, such as those prepared by the Caterpillar Tractor Company using the MD-1, the rippability of-a specific material may be determined.

Jan 1, 1962

By David E. Thompson, Wesley E. Stimpson

The Massachusetts Bay Transportation Authority (MBTA) Red Line Extension Northwest is currently in the early stages of construction. The 3.1 mile extension of the Red Line from the existing Harvard Square Station in Cambridge, Massachusetts to Alewife Brook Parkway in Cambridge, Massachusetts will include a large, near surface hard rock, rapid transit station chamber at Porter Square in Cambridge (Figure 1). [ ]

Jan 1, 1979

By Robert Uhley, Tsvi Meidav, LeRoy Scharon

Before National Lead built an industrial plant on its Fredricktown property, some 100 miles south of St. Louis, a 750x500-ft area on the proposed site was investigated by electrical resistivity, seismic refraction, and churn drilling. Data were accumulated to prepare an isopach map of the overburden and to determine soundness of the dolomite bed- rock and the depth to bedrock at fixed points. The site was on a gently sloping hillside. Elevations above sea level ranged from 760 ft in the northwest corner to 820 ft along the eastern edge, giving a total relief of 60 ft. There were no major drainage features, but in the northern part of the plant site there was an indicated depression area which later was interpreted as reflecting subsurface conditions in the bedrock. No rock was exposed in the entire plant site area; the surface was characterized by soil and overburden.

Jan 2, 1959

By David J. Hatem

Public-private partnerships (PPP) are gaining in popularity at the federal, state and local levels as the public sector seeks private capital to finance infrastructure and other projects that traditionally have been funded with public funds. In general, a PPP involves a development agreement between a public owner and a private sector concessionaire. Under the development agreement, the concessionaire is responsible for financing, designing, constructing and typically operating and maintaining the completed project for a concession period (often multi-decades in duration). The concessionaire typically enters into an agreement ? the design-build agreement ? with a design-builder to design and construct the project. The concessionaire may secure financing from banks, investors or from a combination of these and other sources (collectively the financier). While the PPP experience in the United States has been modest to date, an increasing number of projects involving tunneling or other significant subsurface work are already being delivered in the PPP mode. Public owners have significant options to address risk allocation for subsurface conditions on PPP projects. The same sound and fundamental principles of fairness in risk allocation that apply in other major subsurface projects should be applied and adopted in the PPP context

Mar 1, 2014

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool is gaining acceptance in subsurface investigations. This tool may be used to obtain near-surface information useful to geotechnical engineers. Along with the lightweight field equipment now available, radar is being used to obtain information that may impact the safety and production of mining, tunnelling, and excavating operations.

Jan 1, 1982

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool has expanded greatly in the last few years. This tool can now be used to produce near surface information which is very useful to geotechnical engineers. Using the lightweight field equipment now available, it is possible to use the radar within mines and tunnels to obtain information which may impact the safety and production of these operations.

Jan 1, 1979

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By S. Peng, Yi Luo

Subsurface strata movements and deformations associated with underground longwall mining activities could cause certain influences to subsurface structures and water bodies. Methods have been developed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining operations in the eastern coal fields. Two new types of strata deformation, vertical and total strains, which could be useful in the field of subsidence research in assessing subsidence influences to the subsurface structures and water bodies, have been introduced. Using the subsurface subsidence prediction model, three types of subsidence influences to surface and subsurface hydrological systems have been identified. Attempts have been made to quantify the two types of subsidence influences that could cause water loss and could lower water levels in aquifers.

Jan 1, 2010

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By B Taylor, S Evans

Bulk explosive technology for underground mining has not seen any significant technological advances since the widespread transition from ammonium nitrate fuel oil (ANFO) to ammonium nitrate emulsions (ANE) commencing in the 1980s. The in-hole energy profile that conventional ANE systems deliver is limited by the physics of chemical gassing and simple control systems. This compromises the range, precision, and accuracy of energy delivery into the blasthole, and in some cases limits the length of charge that can be delivered. Orica’s 4D™ bulk system removes many of these constraints, enabling better blasting performance across all underground mining methods. This paper reviews work completed at three mining operations across Australia, the United States, and Chile with a focus on how this system can improve mining operations and deliver sustained commercial and productivity benefits into the future. These benefits include improved ore recovery, reduced dilution from waste rock, and reduced overall explosives consumption. This paper also reviews how this new technology can be applied for planning future mining operations.

Sep 1, 2024

By Odette Corbu

The Canadian Trade Commissioner Service: Who we are ? A worldwide network of professionals in international business development, with preferred access to business knowledge and contacts, committed to advancing Canada?s interest ? Our global presence ?At home: 17 Regional Offices with over 100 trade officers ? Abroad: 149 offices in 101 countries with over 900 trade officers.

May 1, 2009

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010

By Bonifacio Digay

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia.The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.

Jan 1, 2012

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine&apos;s accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By C. Allen, V. Hensel, J. S. Stachulak

"Vale has been actively evaluating new technologies to curtail diesel emissions. This paper discusses the selection, installation, operation, and evaluation of the MANN+HUMMEL SMF®-AR diesel particulate filter system to reduce diesel particulate matter emissions in underground mines. The system uses a sintered metal filter element, an iron fuel-borne catalyst with an onboard dosing system, an electric heater that uses onboard power, and a sensor-based control unit. More than 6,000 h of testing demonstrated that the system represents a breakthrough in the successful control of soot emission from light-duty vehicles with differing soot emission levels, exhaust temperatures, and duty cycles.RÉSUMÉ La compagnie Vale évalue activement de nouvelles technologies pour réduire les émissions de diesel. Le présent article discute du choix, de l’installation, du fonctionnement et de l’évaluation du système MANN+HUMMEL SMFMD-AR de filtrage des particules de diesel pour réduire les émissions de particules de diesel dans les mines souterraines. Le système utilise un élément filtrant en métal fritté, un catalyseur à base de fer dans le carburant avec un système de dosage intégré, un élément de chauffage électrique qui utilise l’alimentation incorporée et une unité de contrôle avec un capteur. Plus de 6 000 heures d’essais ont démontré que le système représente une avancée pour réussir à contrôler les émissions de suie des véhicules légers avec différents niveaux d’émission de suie, différentes températures d’échappement et différents cycles opératoires."

Jan 1, 2015