Search Documents

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

By K. A. SPENCER

THE production of soft coal from strip mines in the United States has shown a remarkable growth in the last sixteen years, increasing from one and one-quarter million tons in 1914 to approximately twenty-two million tons in 1929. This is a growth of approximately 1660 p& cent, as compared with a growth of approximately 20 per cent in the underground mines for the same period. But even with this marked in- crease the total tonnage produced by open-face mining represents only 4 per cent of the nation's soft coal tonnage.

Jan 1, 1931

By Terrence R. Lejcher

Strip mining has played a key role in the production of coal used to produce energy in this country. About 56 percent of the 1.3 x 106 hectares (3.2 x 106 acres) that had been disturbed by surface mining as of 1965 can be attributed to stripping (Udall, 1967). The runoff from these stripped areas is usually heavily polluted with high concentrations of total dissolved solids, iron, aluminum, manganese, sulfates, and has low pH values with high acidity. Another problem of a most serious nature in our large cities is the volume of treated solids to be disposed of after sewage treatment. Chicago is presently producing about 664 metric tons/day of dry weight solids (Horn and Earles, 1968). Disposal methods most commonly used include lagooning, incineration, and landfilling. The high cost of land in an urban community is prohibitive of lagoon storage. Incineration and landfill disposal create air and water pollution problems. Many countries including Australia, England and Israel have long realized the value of sewage solids if they are recycled back to the land. In the United States, the value of such solids in reclaiming strip mined land has been recognized by relatively few people. This paper is concerned with the use of anaerobically digested sludge to reclaim strip mined land.

Jan 1, 1972

By Thomas A. Earl

Strip mining of coal, and to a lesser extent limestone, gravel and other mineral deposits in the Appalachian region of the eastern United States has left many large and small areas of devastated land where mining predated reclamation requirements. In Pennsylvania alone, there are between 250,000 and 370,000 acres of strip-mined land 1,2/. A higher percentage, and a greater total acreage of land in Pennsylvania is in need of some form of reclamation than any other state, with the neighboring states of Ohio and Nest Virginia also having nearly the same magnitude of mining.2/ Recent legislation governing strip mining of coal proposed royalties to cover reclamation of such presently unusable land. However, in Pennsylvania and other states some progress has already been realized by utilizing abandoned strip mines and gravel pits for waste disposal sites. Given acceptable hydrogeologic settings, such use of these mined areas for landfilling has provided the incentive for ultimately restoring unreclaimed land to beneficial use, at no cost to the general public.

Jan 1, 1975

By Thomas A. Earl

Much of the strip mining in the Appalachian coalfields was done prior to backfilling and regrading requirements, resulting in many devastated areas which also have serious acid mine drainage problems. Economic incentive or justification for reclaiming these thousands of acres of land does not exist unless some value can be attached to the open cuts and weathered overburden piles. In Pennsylvania many of these old strip mine cuts are being successfully used for sanitary landfills and sludge disposal sites, and multiple benefits are realized. Given proper regulatory control, this technique could be beneficially applied to many other areas in the east.

Jan 1, 1977

By K. R. Bixby

OPENING of numerous stripping operations in Ohio, Pennsylvania, and other districts, particularly outside the Middle West and Southwest where the large-scale stripping mines predominate, holds the limelight for the year 1940. Several factors are responsible for this expansion. One is the scarcity of untested and undeveloped properties in this central field. Another has been the development of earth-moving and preparation equipment suitable for these smaller tonnage tracts. Draglines of the Walker type, small long-range .hovels, and large-capacity tractor- drawn scrapers have to be considered. Wash boxes, designed for light tonnages, costing a few thousand dollars, have made their contribution.

Jan 1, 1941

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935

By R. RAMSDEN

The deep South African gold mines rely on refrigeration to provide a safe working environment. Chilled water, which is produced in large central refrigeration plants, is distributed throughout mines In insulated pipes. In view of the high cost of the insulation materials and recent regulations which prohibit the use of certain insulation materials, a careful examination of the actual benefits of insulating chilled water pipes was undertaken. The objective of the investigation was to produce general guidelines regarding the use of insulation, but the results of numerous studies have shown that the use of insulation is extremely site specific and thus no general guidelines can be given. To assist ventilation engineers with studies on insulation requirements for their cooling systems a computer program has been developed. This paper describes the personal computer program which contains the same user friendly interface as developed for other COMRO programs. Is fully menu driven and incorporates a comprehensive HELP facility which provides background information and assistance with the selection of input data. The effects on the ventilation air and chilled water temperatures from not insulating chilled water pipes in certain areas are calculated. Air leakage, heat flow from the surrounding rock to the ventilation air and heat flow from the ventilation air to the water flowing in chilled water pipes are taken into account. A simple cooling system is considered in which cold water is distributed over a distance of 1 000 m through pipes to a single air cooler. The influences of changes in the temperature of the chilled water and ventilation air, as well as air leakage on the insulation requirements are determined.

Jan 1, 1991

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By R. T. Moolick, John E. Neill, O&apos

In selecting a particular stripping method the ultimate aim is the removal of material at the least possible cost. Accomplishment of this goal requires the careful consideration of many factors including geologic and topographic information, proximity of the stripping operation to waste disposal areas, possible problems of land reclamation, types of suitable equipment available, and auxiliary equipment requirements. 4.2-1. Selection of Stripping Methods. The size of an orebody and the distribution of values within that orebody normally will limit the variety of economical stripping methods which need to be considered. Much may depend upon the selectivity required in the mining due to the relationship between ore and overburden, as well as the character of the overburden itself. The following factors concerning the geologic nature and environment of an orebody, as well as the production requirements, must be determined before any selection of equipment is made: 1. The size of the orebody and distribution of the values within that orebody. Is the ore massive or scattered, bedded or disseminated, thick or thin? 2. The nature of the overburden to be removed. Is it a hard dense rock, bedded rock (thick or thin), friable material, earth, sand, elay, marsh, etc.? 3. The character and significance of geologic structures (fractures, faults, shear zones, etc.) associated with the ore occurrence. Are there water bearing formations with resulting water disposal problems? 4. In considering the nature of the overburden, including its alteration products, the physical or chemical conditions which, when combined with anticipated climatic conditions, may render certain equipment inoperable during unfavorable seasons.

Jan 1, 1968

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

By Shengfan Zhou, XUEWEN WANG, Changjun Jiang, Mingyu Wang

In the process of extracting vanadium from stone coal by sulfuric acid leaching - P204 solvent extraction, Fe(III) can accumulate in the organic phase which reduces the extraction of vanadium. In order to eliminate the effects of the accumulation of iron, oxalic acid was used as the stripping agent to strip the Fe(III). The effects of oxalic acid concentration, phase ratio O/A, stripping time and shake velocity on the stripping of Fe(III) were studied. The results showed that the Fe(III) stripping rate can reach beyond 96% at the room temperature with 70g/L oxalic acid using an O/A of 2 at 160 rpm shake velocity for 20min. After 2-stage stripping, the concentration of Fe(III) in organic phase was 0.008g/L.

Jan 1, 2016

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By John G. Cazort

In August 1957, a cutter suction dredge started the removal of overburden from a bauxite deposit near Paranam, Surinam (formerly Dutch Guiana), South America. This event marked the climax of a program of investigation, design and construction which lasted almost five years. Cutter-suction dredges are used predominantly for harbor and river work, and land reclamation. While they have been utilized to remove overburden from ore bodies, notably at Steep Rock, Ontario, and Black Lake, Quebec, the conditions under which one is being used for this purpose in Surinam are unusual. Paranam is a mining town built by Suriname Aluminum Company, a subsidiary of Aluminum Company of America. It is located on the Surinam River, about 30 miles from the Atlantic Ocean. The bauxite mining, drying and shiploading facilities have been in operation since 1941.

Jan 10, 1960

By Paul L. Russell

Of the potential applications of nuclear explosives to mining, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. On an energy yield basis, even the cheapest of the present commercial explosives cost more than the most expensive nuclear explosive. Comparing the energy yield of a megaton thermonuclear device with the yield of TNT shows that one energy yield per dollar is 400 times greater for the thermonuclear device. However, small-yield nuclear devices (a few 10's of kilotons yield) are less efficient blasting materials than chemical explosives, with the result that the heat of explosion is utilized less effectively. While only 1 lb of conventional explosive is required to excavate 1 cu yd of rock, or about 2 million cu yd per kiloton, nuclear devices excavate from 100,000 to 300,000 cu yd per kiloton. This changes the economic situation, and it is thus apparent that nuclear explosives are cheaper only for the large explosions.

Jan 6, 1964

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

By Adams R. W

A commercial scale strong acid leaching plant was commissioned at the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, a member of the Pasminco group of companies, in February 1988. It was designed to upgrade the lead/silver residue product from 26% to 37% lead, thus improving the realised value and increasing overall zinc recovery. This in turn enables the lead smelter treating the lead residue to improve its productivity. The equipment consists of two 250m3 bricklined leach tanks and two 6.5m diameter stainless steel high rate thickeners operating with counter current washing at 95¦C and 120 g/L H2SO4. The present filtration and drying equipment is also being replaced. Two 35m2 squeeze action filter presses equipped with horizontal plates are being installed, together with ancillary drying equipment to ensure that the final product complies with the transportable moisture limit. The new filtration plant is due to be commissioned in mid-1989.

Jan 1, 1989

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985