Search Documents

By Shusen Cheng, Kun Yan

An elastic-plastic stress mathematical model of hot blast stove shell has been established in order to investigate the stress distribution and deformation of the shell. The results show that stress concentration happens along the intersection line of hot blast stove body and the hot blast manifold. The plastic deformation occurs on the hot blast outlet in blast period. The deformation degree of the hot blast shell near the blast outlet in blast period is much larger than that in combustion period. In blast period, the shell near the blast outlet elongates along the horizontal direction and shortens along the vertical direction, the shell near the outlet deforms into an oval. And in combustion period, its deformation isn’t obvious. The repeated deformation of the shell near the outlet between different periods may cause the refractory brick damage and be harmful to the long campaign life of hot blast stove.

Mar 1, 2017

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By W. H. McCormick, H. J. Benecki

CONSIDERING that a typical modern drilling machine strikes approximately 2000 blows per min and may develop a force of 30 to 200 ft-lb, de- pending upon size of the drill used, the importance of uniform stress distribution in this type of drilling becomes obvious. If the rod were perfectly symmetrical, and if it did not rotate, the problem would be relatively simple, however, the necessary forging, machining and heat treating operations prevent attaining this state of perfection. Take the modern hollow drill rod. The blow is transmitted not from the striking end of the rod directly through to the point of impact of the bit in the rock, but rather through a somewhat complex tool. To add further problems, this entire assembly is rotated immediately after the impacting blow. Rather than attempt to discuss the magnitude and distribution of stresses, it is desired to present a few things that will minimize unusual stress concentration and produce a rod in which the stress distribution will approach the theoretical ideal.

Jan 3, 1954

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham, Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

By Shosei Serata

Conventional roof bolting may be giving ground to a new technique that utilizes only the ground itself to stabilize mine openings. This newly developed stress control technique (SCT) has initially been used in sedimentary ore bodies that are both overlain and underlain by weak strata. The technique is also suited to the design of production panels and main entry systems, and is readily adaptable to room and pillar as well as total- extraction mining, including both shortwall and longwall coal mining. In applications where the technique has been used, the requirements for roof bolting and floor renewal were virtually eliminated. The SCT comprises three basic methods and covers a wide range of problems associated with failing roofs and heaving floors in underground mines (see Table 1).

Jan 5, 1976

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By C. W. George, Bruce Chalmers

The authors enumerate the factors which appear, from their observations and practical experience of failure of aircraft components in Great Britain, to be responsible for causing a metal or alloy to fail by stress corrosion. The essential conditions for promoting failure by stress corrosion are: (I) tensile stress at the surface of the component, (either residual or applied), and (2) an attacking medium that may be a solution or a liquid metal. Particular attacking agents are effective only on certain metals. In all instances of stress-corrosion failure experienced, cracking of an intercrystalline form has occurred and examples of such failure in aluminum alloy, steel and copper alloys are described and illustrated. The relation between microstructure and stress corrosion is mentioned and methods of investigating the susceptibility to stress-corrosion failure of metallic materials are described. The precautions to be taken in selecting materials for particular aircraft components and the importance of adequate protection against chemical attack are considered. The authors have given a factual survey of stress corrosion and have made no attempt to advance any scientific explanation of the phenomenon.

Jan 1, 1945

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By James R. Russell

Rock bolts are commonly used to support and stabilize the rock around excavated openings. The assumption is made that the less competent rock near the surface can be supported by bolting it to more competent rock away from the surface. Naturally, a rock bolt can be no more effective than its anchoring mechanism which induces a stress field into the surrounding rock. Details of various types of bolts have been described e1sewhere.l The purpose of the present investigation is to study the stress distribution around an expansion-type rock bolt anchor, using the theory of elasticity. The elastic stress distribution provides some insight into the behavior of rock bolt anchors which may eventually lead to improved designs. Very little information is available on the induced stress field which is rather complex; consequently, photoelastic techniques have been used to obtain a qualitative picture of the stress ditribution.2 The present work provides quantitative information on the stress field induced by an idealized distribution of surface tractions, provided that the assumptions of the linear theory of elasticity are approximately satisfied. FORMULATION OF THE PROBLEM Consider an elastic region which extends to infinity and contains a circular cylindrical hole as shown in Fig. 1. The hole is assumed to be the bolt hole and the surface tractions shown are assumed to be caused by an idealized rock bolt anchor. The relationship between the idealized

Jan 1, 1972

By S. Bastola

Over 80% of roof falls in Illinois coal mines occur at intersections. Regular intersection geometries with sharp corners have been typically analyzed in literature. This study has analyzed stress distribution around typical field 4-way intersection geometry and compared it with similar data for regular four-way intersection geometry. These analyses were performed using 3-D numerical analyses for a typical lithology associated with No 6 coal seam in southern Illinois. Linear elastic and non-linear analyses, using Hoek-Brown failure criteria for different lithological units, were performed. The 3-D models incorporated bedding planes and pre-mining horizontal stresses. Effect of diagonal widths of the intersection and pre-mining horizontal stresses were examined due to their influence on stability. In addition to stress distribution, contours of safety factors, and displacement analyses were performed to assess stability of intersections.

Feb 27, 2013

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024