Search Documents

By H. C. de Wet

The predevelopment and preparation of a total infrastructure in a deep level mining environment, prior to the shaft system being commissioned has major advantages. This paper intends to indicate these advantages and outline an understanding of the disadvantages. These benefits can be classified in three basic groups: the financial and timing advantages, a knowledge of the ore body and the development of required technology to meet the design parameters. The required technology in many aspects was still to be developed prior to successful application. Stemming from the technological evolution are some secondary advantages which will be described in each of the groups. Safety and health considerations and some practicalities made some of the new technology redundant prior to the actual application. In each case the actual achievements and the anticipated benefits will be indicated to allow the reader to distinguish clearly between planned and actual achieved advantages.

Jan 1, 1997

By C. Fairhurst, B. C. Haimson

Pink Tennessee Marble was tested for wedge bit penetration characteristics at static and dynamic (10 - 250 ft/sec) loading rates. No significant differences were found within the dynamic range as far as the energy required to remove a unit crater volume and the force used to cause a certain penetration. Under static loading, however, both the energy and the force required were significantly lower. Tests run on bits of varying width indicated that as the wedge bit narrowed to an almost conical shape, the energy used per unit crater volume became considerably lower.

Jan 1, 1971

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923

By Alfred W. G. Wilson

In this paper is presented a review of the changes that have taken place in certain Canadian non-metallic mineral industries since 1909. The fifteen-year period 1909 to 1923, inclusive, has been selected for two reasons. In the first place, statistical treatment of the subject under review has been nearly uniform throughout the period. In the second place, this decade and a half is itself further subdivisible into three well marked quinquennial periods, the middle one covering the period of the great war when industrial conditions were greatly disturbed. It then becomes possible to institute certain comparisons between equal periods before and after the war disturbances. The items selected for inclusion in this review are certain of the more important members of that class of minerals usually grouped together under the heading of non-metallics. They are all minerals of which Canada is known to possess important resources, and which are indispensable to many of our greatest manufacturing industries.

Jan 1, 1925

By Dilip K. Sinha

In the paper some interesting cases of applications of Operations Research and Computer Methods as worked out by the author and accepted by the management of some of the newly formed Indian mining organisation for implementation are highlighted. The main emphasis on the application cases was to use simple techniques and methods which yield the result in shorter time period, The case problems mainly deals with the production system optimisation in unit mines, areas/divisions and at the corporate levels. Also the management decisions regarding reorganisation of transport and distribution system of material and mineral are attempted to be optimised. Further, the case of management system development with computer aided decision making worked out for single large Iron Ore Project captive to a steel plant is outlined. Finally, the case of a large mining company having decentralised units and divisions geographically dispersed throughout the country, computerised management decision-information system designed on the basis of inputs and outputs of decision models relevant for different levels of management in the organisation is depicted.

Jan 1, 1986

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of ilie cell at temperatures between 800 and 1100 K was measured. Whilc the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03V were found. It was difficult to determine temperature dependence of ilie Emf. The Gibbs energy change for the reaction, 113 LbN (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be tJ.Gor (LiMgN) -13.2 (±2.9) kJ/mol. Using thermodynamic information on ilie binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be AGO f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of ilie stability region of the LiMgN phase. The diagram was found to be in good agreement with the isoiliermal phase diagram determined by ilie alloy equilibration meiliod. Although the obtained data includes large uncertainties, the results provide a better understanding of the iliermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of the cell at temperatures between 800 and 1100 K was measured. While the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03 V were found. It was difficult to determine temperature dependence of the Emf. The Gibbs energy change for the reaction, 113 Li3N (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be !'J.Go, (LiMgN) = -13.2 (±2.9) kJ/mol. Using thermodynamic information on the binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be !'J.Go f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of the stability region of the LiMgN phase. The diagram was found to be in good agreement with the isothermal phase diagram determined by the alloy equilibration method. Although the obtained data includes large uncertainties, the results provide a better understanding of the thermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By P. E. Cavanagh

Abstract Many investigators have been interested in developing some non-destructive method for detecting or determining the changes in physical properties in steel occurring during endurance tests or normal service life of a part which fails in fatigue. This paper presents a broad discussion of some of this work and the possibilities of developing useful test procedures based on some of the information obtained in the past. Changes in magnetic properties, electrical resistance, damping capacity, X-ray diffraction patterns, and remaining fatigue life at load different from service load have all been investigated as possible means for following the sequence of events during fatigue failure. In some special instances, tests such as these may be used to predict fatigue failure. As an in stance of practical application of the continuous determination of changes in magnetic properties during fatigue, a brief account is given of work done in non-destructive inspection of mine hoist-rope. As a result of extensive experiments and field crisis, it has been found possible to detect the beginnings of failure in a wire rope in service. The test method used will detect plastic deformation in a wire rope, no matter what its cause. There is no possibility of determining the remaining useful life of a rope by calibrating changes in magnetic properties in terms of remaining fatigue life. A change in magnetic properties at a point in a rope may indicate a decrease or increase in fatigue life, depending on the overload history of the rope. A continuing change in magnetic properties ac a point, however, does reliably indicate a developing weak point which will eventually lead to failure. The important point about any change in magnetic properties is not the magnitude of the change, but whether or not it continues.

Jan 1, 1947

The Ramu chromite deposit occurs in the Marum Ophiolite complex and is the most economically attractive chrom-ite deposit in Papua New Guinea. Its lateritic nickel, chromite and cobalt potential has attracted several compan-ies to prospect the deposit.In the present work, the compositions of chromite in the Ramu lateritic deposit and coexisting olivine-chromite pairs in Marum Ophiolite dunite were analysed with the electron microprobe for Fe, Mg, Cr and Al. The results were used to determine the relationship between the cations in the tetrahedral and octahedral structures of the chromite. In addition, the Fe, Mg, Cr and Al cations of the coexisting olivine-chromite pairs were used to calculate the equilibrated temperatures of crystallisation of the chromite. The variation of Fe", Mg and Cr cation values of the chromite in relation to the calculated temperatures was studied by regression analysis.

Jan 1, 1994

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By V. N. Krivobok

THE study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency towards brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had little use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: ?. . . manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 per cent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper.

Jan 1, 1927

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. Strong outbursts often have occurred in geological tectonic zones and concentrated stress areas. There are some particular characteristics of these strong outbursts, including the effects of ground stress, gas pressure and the properties of coal associated with the outbursts.

Jan 1, 1986

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By Hennessy F. L

It is generally recognised that slags are active participants in pyrometallurgical processes, and not merely inert liquids which must be produced. to effect separation of gangue material in smelting, or of impurities in refining. The importance attached to slag-metal reactions in steelmaking is shown by the numerous investigations in this field. However, there are still many important reactions of slags which require explanation. In this paper some new aspects of the reactions of slags will be discussed, as far as possible quantitatively.FREE AND COMBINED OXIDESMetallurgical experience indicates that variations in the composition of slags produce changes in the chemical behaviour of the various components. These variations have been generally ascribed to changes in the proportions of free and combined oxides, i.e., compounds have been assumed to be present in the liquid slag.Considerable support for this view has been adduced from the existence of compounds such as metallic silicates, phosphates, etc., in the solIdified slag. However, this does not imply that such compounds necessarily exist in the molten slag.The most direct evidence as to the nature of molten slag is to be obtained from a study of the liquid state. In...

Jan 1, 1950

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012