Search Documents

By R. L. Lloyd

UNLIKE the development of sintering lead, copper and zinc ores, the sintering of fine irony material had its birth, not as a result of gradual growth along lines aimed at the production of sintered and agglomerated product, but because the success of the sintering operation in other lines had been brought to the attention of the ironmasters, who were immediately attracted by the prospect of being able to convert their own fines-into a similar product. The abundance of iron ores in the United States and their comparative cheapness had led iron men into the habit of not paying particular attention to the fine material blown out of their blast furnaces. Hundreds of thousands of tons had been stacked up and used only during times of shortage of ore and then usually without any preliminary preparation, though many attempts had been made to briquette it. Briquettes proved good material, but the operation of briquetting was too expen-sive when applied to iron-ore fines. The development of the iron-ore blast furnace in the United States tended toward large units, high columns and heavy blast pressure, and this tendency is still peculiar to this country, whereas in the other countries the tendency has been to smaller units, lower columns and lower blasts. The high blast pressures and swift driving of the American blast furnace tend, of course, to produce more flue dust than European practice, and this production of flue dust was augmented when large quantities of soft ore, of which the Mesabi is typical, came on to the market. These ores are desirable chemically but physically they are soft, friable and fine, and when they are used in the iron blast furnace the flue dust produc-tion is increased. The necessity of rehandling the flue dust lead to briquetting on an extensive scale. The binders used were either chemical or mechanical, and in one system the briquettes were kiln fired in very high temperatures. Rotary kilns, coal or oil fired, were used extensively, and gave a product of hard and more or less nodulized material, but at considerable cost. This was the situation in regard to iron flue dust when the late James Gayley and his associates became interested in the idea of sintering the iron blast-furnace flue dusts under their own fuel (included coke dust) of which they carried between 15 and 30 per cent.

Jan 10, 1922

By Perry Harrison

THE mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process-flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiating by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported.

Jan 1, 1930

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By De-qing Zhu, Feng Zhang, Jian Pan

Sintering performance of a series of sinter blends with high ratio of limonite was investigated. The metallurgical performance and mineralogy of product sinter were also examined. The results show that good sintering performance could be obtained when the ratio of limonite was below 43% in the blends of iron ore fines, while good microstructure and metallurgical properties were achieved under optimum sintering conditions. In contrast, sintering performance will rapidly deteriorate when the ratio of limonite is elevated up to 63% in the blends.

Mar 1, 2017

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By Cheng Pan, Qiugang Yuan, Xuewei Lv, Mei Liu, Enguang Guo

Land-based nickel resources include nickel sulfide and nickel laterite. With the consumption of high grade nickel sulfide, use of nickel laterite has received more and more attention. The mineralogy and sintering behavior of limonitic nickel laterite with high iron and low nickel and silica was studied to offer technical support for producing ferronickel through sintering–blast furnace route. The mineralogy results showed that the main phases in this kind of nickel laterite are goethite (FeO(OH)), gibbsite (Al(OH)3) and NiFe2O4. The TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) revealed hydroxide minerals in addition to absorbed water. After the sintering experiments the chemical composition, phases present (XRD analysis) and physical properties of the sinter were studied. The content of FeO in the sinter increased with increasing basicity up to 1.3, and then decreased with further increase in basicity. The yield of sinter increased (from 73% to 80%) with increase in the basicity from 1.1 to 1.7, and then the yield decreased with the further increase in basicity. Mg(Ni)(Fe,Al)2O4 is the main phase in the sinter while MgCaSiO4 and Fe2SiO4 is the main binder phase when the basicity is 1.1~1.5, and MgCaSiO4, Fe2SiO4 and SFCA is the main binder phase when the basicity is 1.7~2.1.

Jan 1, 2014

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By Sibin Zhang, Shengli Wu, Youhao Yin, Yuandong Pei, Zhixing Zhao, Jiangshan Shi, Zhengyun Fan

Spraying medium to achieve an energy-saving and emission reduction for iron ore sintering has been researched, such as spraying natural gas, coke oven gas, oxygen, sintering flue gas and gas from annular cooler. This paper focuses on effect of spraying steam on sintering surface on reduction of NOx and dioxin emissions in practical sintering production in Shougang Jingtang. It can be found that, with the increase of sintering bed spraying steam amount, NOx and dioxin of flue gas showed a decreasing trend. As spraying steam 1 t/h for 550 m2 sintering machine in Jingtang, NOx content decreases 2.6–9.5 mg/Nm3, and dioxin decreases 0.007–0.014 TEG ng/Nm3.

Mar 1, 2018

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H. R. MacMichael

THE rate, at which zinc ore can be sintered varies widely, depending on the characteristics- of the ore. A coarse table concentrate already roasted to a very, low sulfur content may sinter at the rate of-8.6 tons per hour per 100 sq.ft., of wind-box area. At the other extreme is a finely ground flotation, concentrate, with considerable sulfur remaining in the ore as delivered to the sinter plant, for which corresponding rate may be only 3.8 tons per hour, or 44 per cent of the first rate. A usual, size-of sinter machine in zinc plants is one with wind-box 3.5 by 33 ft., making 115.5 sq. ft. of area, and using a 100-hp. fan. Such a machine with the coarse concentrate described would produce 10 tons of sinter per hour; and with the fine, flotation concentrate would produce only 4.4 tons per hour. Ore of the latter class is -sintered at the plant of the Mexican Zinc Co. (subsidiary of the American Smelting & Refining Co.) at Rosita, Mexico. ; Consequently, an unusually large sintering capacity per ton of ore to be treated is required, and provision was made for treatment of 9000 tons concentrates per month, preroasted to. 5 to 9 per. cent sulfur. For this duty three of the usual 33-ft., 100-hp. sintering machines would have been needed.. Considering the auxiliary equipment. necessary for proportioning, handling, and mixing charge, as well as means for disposition of the sinter, a three-unit plant becomes-very complicated, especially if the capacity should be doubled later. After much study it was decided to build a single sintering unit of ample capacity for the work, the plant thus being much simpler and cheaper in construction as well as in operation (Figs. 1 and 2). The sintering machine was built with a wind-box 5.25 by 60 ft. (315 sq. ft.) and provided with a 300-hp. fan.

Jan 1, 1932

By Guilherme Santos Garcia

Este trabalho tem por objetivo avaliar a sinterização a plasma do alumínio com a utilização da técnica Active Screen, em comparação com o processo em forno resistivo. Foi utilizado pó de alumínio atomizado, com granulometria entre 30 e 100µm, sendo misturado junto aos pós cerca de 1% em massa de estearato de zinco como agente lubrificante. Foram confeccionados corpos de prova com 13mm de diâmetro e 10mm de altura. A compressão dos pós se deu através de uma prensa hidráulica, de ação simples, utilizando pressão de compactação de 600MPa. O tempo te sinterização foi mantido em 60min a temperatura de 500ºC, utilizando atmosfera de nitrogênio. Foram realizadas medidas de densificação, antes e após a sinterização, medição de rugosidade e microdureza superficial, bem como análises em MEV da superfície das amostras. O processo a plasma se mostrou satisfatório, sendo capaz de produzir amostras com boa densificação. As medições de microdureza superficial evidenciaram valores semelhantes entre os processos, sendo a amostra sinterizada via plasma a apresentar menor variação de microdureza. Através da análise de EDS das imagens, foi identificada a presença de estearato de zinco em ambos os processos, evidenciado que a extração do lubrificante não foi totalmente eficaz. Ainda, houve uma leve redução da rugosidade no processo a plasma em relação ao convencional.

Aug 17, 2017

By Luiz Antônio Fonseca Peçanha Júnior

As propriedades e caracteristicas do diboreto de titânio (TiB2) e nitreto de alumínio (AlN) tornam esses materiais ideais para aplicações termomecânicas. Entretanto, a dificuldade de sinterizar compósitos cerâmicos à base de TiB2 – AlN tem limitado suas aplicações na indústria contemporânea. Nesse sentido, o presente trabalho tem por objetivo avaliar a técnica de sinterização por plasma pulsado (SPS), como uma alternativa para consolidação de compósito cerâmico em um curto intervalo de tempo. Após a caracterização das matérias primas, as amostras foram sinterizadas utilizando temperaturas entre 1.500°C e 1.900°C, além de 80 MPa de pressão e 10 minutos de permanência na temperatura máxima. A técnica “SPS” mostrou-se eficiente na sinterização desse sistema, alcançando densificações de até 98%. E ainda, como era esperado, a incompatibilidade dos coeficientes de expansão térmica entre o TiB2 e o AlN provocaram um processo de tenacificação nos compósitos.

Aug 16, 2017

By Mariane Abreu Alves Campos

A utilização do wBN como ferramenta de usinagem pode eliminar a necessidade de retífica das peças. Portanto, neste trabalho, os experimentos realizados tiveram por objetivo o estudo e caracterização de compósitos à base de wBN, diboreto de titânio (TiB2) e alumínio (Al) para obtenção de pastilhas para usinagem. A composição utilizada para a investigação utilizou 70% de wBN. Os compósitos foram obtidos sob altas pressões e altas temperaturas via aplicação cíclica . As patilhas atingiram aproximadamente 4,5 mm de diâmetro, e altura de 4,0 mm. As amostras foram caracterizadas por ensaio de dureza Vickers, microscopia eletrônica de varredura, microscopia confocal e densidade. De forma geral, os melhores resultados foram para amostras com ciclos de um minuto cada, para os três ciclos, sendo pouco dependente do valor da pressão aplicada. Foi observada dureza maior que 17GPa, baixa porosidade e um valor de densidade aparente muito próxima à teórica.

Aug 16, 2017

By Diego Santana Torga

É comum encontrar sintonia de controladores PID que não levam em consideração o sinal de controle aplicado a variável manipulada. Portanto, variações rápidas e amplitudes elevadas podem ser geradas, que, na prática, pode ser inviáveis, devido à limitação física de atuadores e equipamentos industriais. Nesse artigo é desenvolvido um método de sintonia em que os parâmetros do PID são calculados por meio do Algoritmo Genético. A função de custo proposta penaliza tanto a amplitude do erro de controle quanto à variação da variável manipulada. A estabilidade é garantida com as restrições de robustez sobre o pico das funções sensibilidades. Exemplos simulados demonstram as vantagens da sintonia proposta.

Oct 30, 2017