Search Documents

By Rudolf Greuer, Gerald Jalkanen, Huann-Sheng Chen

A short cut is presented where the average grade above a primary grade cutoff and its associated byproduct grade(s) are estimated by screening the primary and byproduct grades. For the primary variable, choose samples whose grades are above a cutoff of interest. Compute variograms for the subset of the primary variable. Then using this variogram, krige the blocks of interest only using the samples whose grades are above the cutoff. The next step is to screen byproduct grades by choosing byproduct samples whose associated primary grades are above the cutoff of interest. Next compute variograms for this subset of byproduct samples. Then using this variogram, krige the blocks of interest using byproduct sample grades whose associated primary sample grades are above the cutoff of interest. The results are the average grade above a primary cutoff for both the primary and the associated byproduct variables. Using two simulated primary and reference data sets a case study resulted in the screening krigings performing better than the indicator kriging approach in the first case study. A second case study had mixed results with the primary indicator approach performing better than the primary screened approach. The byproduct screened approach performed better than the byproduct indicator approach.

Jan 1, 2002

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By M. W. Harmer, J. M. Quist

Laboratory test work, pilot plant testing and plant experience with wet, fine-mesh screens are discussed. High-frequency, low-amplitude, fine-mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with hot ferric chloride to remove lead and copper contaminants before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1991

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By A. Garnier, K. Tremblay-Bouliane, B. Gaillet, S. Moineau, D. Tremblay

"A heptapeptide library displayed on M13 bacteriophages (phages) was screened to identify peptide sequences able to selectively bind to gold, chalcopyrite, sphalerite, pyrite, and silica ores, and to evaluate phage potential as bioflotation reagents. Many peptide sequences were isolated through biopanning and differed from known sequences. Adsorption isotherms were determined and a receptor/ligand interaction model was identified and used to compare affinity of peptide sequences toward ores. Some phage sequences have slightly lower affinity to sphalerite than other sulphides. Adsorption was higher on sulphides than on silica. Induction time measurements suggested filamentous M13 phages lower hydrophobicity of the ore surface.RÉSUMÉ Une librairie d’heptapeptides présentés sur des bactériophages M13 (phages) a été criblée afin d’identifier les séquences peptidiques affinitaires à des minerais d’or, de chalcopyrite, de sphalérite, de pyrite et de silice et d’évaluer le potentiel de ces phages en tant que de bio-réactifs de flottation. De nombreuses séquences peptidiques ont été isolées par bio-criblage et différenciées d’autres séquences connues. Des isothermes d’adsorption ont été déterminées et un modèle d’interaction récepteur–ligand a été identifié et utilisé pour comparer l’affinité des séquences peptidiques par rapport aux minerais. Certaines séquences de phages possèdent une affinité légèrement inférieure pour la sphalérite comparativement aux autres sulfures. L’adsorption sur les sulfures était plus élevée que sur la silice. Des mesures de temps d’induction suggèrent que les phages filamenteux M13 diminuent l’hydrophobicité de la surface des minerais."

Jan 1, 2016

By Rubisov DH

This paper is related to the problems of the mathematical modelling of vibrating screening process and to predicting the screening operation results. The authors propose a model of screening based on the interpretation of granular material segregation on a screen surface as an instantaneous process. Results show an agreement with laboratory and pilot plant tests. Derived formulae can be used for screen sizing and screening result estimating.

Jan 1, 1993

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By C. G. Kemsley

THE ore as hoisted is very wet, and difficulty was experienced i~ screening it to remove the fines before going to the secondary crusher. In fact, the fines had a tendency to form balls and roll down the screen, and only a small percentage was removed. Their inclusion with the other ore going to the Symons secondary crusher caused excessive spring action and pounding between the adjustment ring and main frame, resulting in abnormal wear between the two. To overcome this, it was decided to wash the fines through the primary screen, and use an Akins classifier to de-water the screenings, pumping the overflow from the classifier up to the mill and discharging the oversize onto the mill-feed belt.

Jan 1, 1945

By Carl W. Lam

The increased obsolescence rate of electronic products has made it evermore pertinent to understand the potential environmental impact of materials choices to help guide electronic waste (e-waste) management and promote awareness of high burden materials. Methods for screening for the performance of materials and their potential burden on human health and the environment can be used to comparatively select constituents of present and prospective electronic products. These methods should be able to yield more robust information when linked to other decision-making strategies where integrated data on consumer preferences, production quantities, and regulatory initiatives are sparse or unavailable. A framework is presented here for generating metrics of ecological toxicity, human health toxicity (cancer and non-cancer categories) and global resource consumption for evaluating environmental impact of materials (specifically metals) in electronic products. The time-dependent impact trends of United States? printed wiring board (PWB) metals usage, principally derive

Jan 1, 2010

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By A. A. Gustafson

The Freeport Sulphur Co. built a portable crusher in 1944 that solved a problem that none of the crusher manufacturing companies contacted were able to do. Two of these crushers have now been in service for 6 years, giving satisfactory service in handling a million tons per year, and having a capacity of over 2000 long tons per 8-hr shift. These machines reduce ton size blocks of sulphur to 12 in. and also feed the conveyor system at the rate of 350 long tons per hr per machine.

Jan 10, 1950

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Lewis. Clifford J.

The purpose of this article is to present design information and operating data on a pilot gas scrubber which is believed to be a new approach for removing noxious gases and particulate matter from the off gases of coal burning power plants and smelters. This principle of scrubbing gases, particularly, scrubbing with an aqueous slurry of lime, was conceived by the author early in 1972. The National Lime Association financed the design, fabrication and initial operation of the unit. The unit was fabricated by Hazen Research Inc. of Golden, Colorado. It has been tested on the off gases of two coal burning power plants and one smelter. The current environmental program has stimulated research and development activity directed toward the removal of sulfur oxides, oxides of nitrogen, particulate matter and other undesirable substances from gases discharged into the atmosphere. At present, most of this effort is focused on the removal of sulfur dioxide and particulate matter by aqueous scrubbing of the gases. This presentation deals particularly with the removal of sulfur dioxide using an aqueous slurry of lime as the scrubbing medium. In recent papers, the author has called attention to-the sludge problems resulting from aqueous scrubbing and to some earlier data on the pilot scrubber about to be discussed.1/

Jan 1, 1973

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

By Steve O. Green

Introduction The US coal mining industry is in the midst of a serious economic crisis. To overcome increased operating costs, operators must take advantage of technological advancements in mining systems and equipment. A relatively new concept available to underground operators is that of extending the cutting depth for continuous mining machines (continuous miners). This system is referred to as deep-cut mining, and may be described as mining cuts to depths greater than the standard 6 m (20 ft). Productivity is increased through the reduction in continuous miner tram time since the machine stays longer in each working face. To successfully implement a deep-cut mining system, three problems must be overcome: Exposing personnel to unsupported roof, methane removal, and controlling respirable dust. Remote control cutting The solution to the unsupported roof problem is remote control. Recent advances in remote operation, especially in radio remote controls, have resulted in what is generally accepted as a safe and reliable tool. By installing remote control on the continuous miner, the operator and helper can now be stationed in a supported area. This allows for improved visibility while cutting coal. With this in mind, the limiting factor now becomes the position of the haulage equipment operator. North River No. 1 uses Joy 21SC shuttle cars and Jeffrey 4110 diesel ramcars. These cars are pulled against the bumper of the continuous miner. Thirteen meters (43 ft) can be cut with the shuttle car and 14 m (45 ft) with the Ramcar before the operator of the car is inby permanent supports. By loading away from the bumper, about 1.5 m (5 ft) can be added, bringing total cut depths up to 14.5 and 15 m (48 and 50 ft), respectively. Methane removal The second problem involves methane removal, and the line curtain-to-face distance. In other words, how to maintain the line curtain to allow sufficient ventilation to remove methane and not expose workers to unsupported roof. The solution, in most cases, is to use a blowing-type ventilation system. Unlike the exhausting system that, to be effective, must be installed within 3 m (10 ft) of the working face, the blowing system can be effective at greater distances from the face. Numerous studies have documented the advantages of a blowing-type ventilation system over an exhausting system. Furthermore, a blowing system can be significantly improved by in¬creasing the velocity of the air delivered without increasing the volume of air. With this greater ventilation efficiency, it is possible to secure ventilation plan approval from the Mine Safety and Health Administration (MSHA) for a greater curtain set-back distance. This eliminates the need for personnel to travel inby permanent supports to extend the face brattice. The distance from the face MSHA will approve, however, is on a mine-by-mine basis. MSHA will evaluate the particular mine's face methane liberation rates, along with the specific proposals regarding face ventilation volumes and velocities. Dust control The third problem is controlling respirable dust. This is actually a result of the solution to the second problem. In the blowing system, while mining on the slab cut, both the continuous miner and haulage units are located on the dusty side of the line curtain (Fig. 1). In the early 1970s, underground operators virtually abandoned this system, in order to comply with the 2 mg/m3 (0.87 gr per cu ft) federal dust standards. The blowing face curtain did offer increased face ventilation efficiency. With that, greater curtain-to-face distances were also

Jan 8, 1987

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988