Search Documents

By G. P. Sturm

This work was undertaken by the Bureau of Mines in cooperation with the Environmental Protection Agency to determine photochemical specific reactivities of emissions from automobiles using leaded-premium-and regular-grade fuels and prototype lead-free fuels of comparable octane quality. Emissions were photoirradiated in a 100-ft3 environmental (smog) chamber constructed of aluminum and Pyrex glass at three sets of initial hydrocarbon (HC) and oxides of nitrogen (NOx) concentrations. Reactivity was measured and expressed in terms of rate-of-NO formation (RNo2) and dosages of oxidant, peroxyacetyl nitrate (PAN), peroiypropionyl nitrate (PPN), and formaldehyde (HCHO). The results indicate that the evaporative emission samples and the evaporative plus exhaust emissions samples from the lead-free fuels have, in general, higher reactivities per gram than those from the leaded fuels. For the samples containing only exhaust emissions, the only trend observed was the lower specific reactivity exhibited by the leaded premium fuel exhaust. These differences in specific reactivity are taken to reflect the differences in hydro-carbon composition of the fuels and their evaporative and exhaust emissions rather than any difference in lead content per se.

Jan 1, 1973

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By H. B. Carroll

This Bureau of Mines report evaluates the performance of commercially available portable instrumentation for the detection of carbon monoxide, carbon dioxide, oxygen, and methane at conditions simulating an industrial work atmosphere. Portable instrumentation included in the study was gas-detection tubes (length-of-stain and color intensity), catalytic detector, liquid absorption detectors, paramagnetic oxygen detector, galvanic detector, and pelement or hot-wire methane detectors. Evaluation of the instruments was in atmospheres with 50 and 80 percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the thresh-old limit value. Correlation of the results from the portable gao analyzer with measurement from the standard instruments was made by calculating and plotting an estimated line of regression, prediction, and confidence limits and the correlation coefficient for each detector system. Relative humidity in the 50-to 80-percent range did not appear to contribute to instrumental uncertainties in either performance or operation. Considerable deviation in detection precision between the portable gas-detection systems and the standard systems was established, especially at the lower gas concentration levels. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than difference in the tubes themselves.

Jan 1, 1973

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By I. Liebman

A Bureau of Mines study is in progress to determine the effectiveness of passive water barriers in suppressing coal-dust explosions. A 2.9-ft3-capacity water-filled plastic tub was found effective in suppressing dust explosions propagating at speeds of 250 to over 1,000 ft/sec. Work directed at determining the limitations of water barriers showed that the passive water barrier technique is also feasible for the suppression of weak dust explosions propagating at speeds of 100 to 250 ft/sec. For relatively slow accelerating flames, dynamic wind forces appear to be the important quantity governing fragmentation of the plastic tub and subsequent water release and dispersion, whereas dynamic impulse appears to be the significant quantity for rapidly accelerating flames. The acoustic approximation (relation between static pressure and flame or wind speed) is shown to be valid in a long single mine entry. This relationship appears to be useful in predicting the regions within a long single entry where passive water barriers are effective in quenching a dust explosion.

Jan 1, 1974

By Oleg Terichow

Electrophoretic mobility measurements were made on samples of Florida phosphate slimes to determine the optimum conditions of coagulation and precipitation in aluminum sulfate solutions. The addition of silica sand and other selected materials as mutual coagulants has demonstrated the practicability of coagulating two dissimilar particle systems by elimination of the repulsive double layers. By proper selection of the solution and its concentration, the reduction of the double layer to a zero point of charge causes coagulation and rapid precipitation of both particle systems. Confirmation was found in filtration tests and sedimentation tests.

Jan 1, 1973

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By J. E. Dooley

An analytical procedure developed by the Bureau of Mines was applied to the separation and characterization of a 370° to 535° C distillate from Swan Hills (south field), Alberta, Canada, crude oil. Investigators determined the general characteristics of the crude oil by the Bureau&apos;s routine method for crude oil analysis. Suitable fractions were prepared for instrumental analyses by utilizing such techniques as isothermal and molecular distillations, chemical treatment, silica-alumina gel chromatography, and gel permeation chromatography (GK). A detailed characterization of the 370° to 535° C distillate was possible by the application of GPC-mass spectrometry correlations and nuclear magnetic resonance spectrometry. Semiquantitative data based on mass Z series distributions were determined and are shown. The data will be valuable in developing future processing techniques and in calculating yields for converting high-boiling distillates into more useful energy forms.

Jan 1, 1973

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973