Search Documents

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968

By A. F. Colombo

Bench-scale research was undertaken to determine if adding ammonia to cyanide leaching solutions would enhance the extraction of copper from an argillaceous Michigan copper ore. Two leaching techniques, (1) rolling using a tumbling bottle and (2) aerating using a modified Buchner funnel, and variations in pulp temperature; were employed in evaluating the effect of ammonia concentration on copper extraction. Under these experimental conditions, the extraction of copper was shown to be independent of ammonia concentration and entirely dependent on cyanide concentration.

Jan 1, 1968

By E. L. Litchfield

The electrification of ammonium nitrate-fuel oil (AN-FO) blasting agents by pneumatic loaders is described and discussed. The consequences of the electrification are considered in light of the initiation requirements of electric blasting caps. It is recommended (1) that semiconductive loading tubing be utilized and (2) that the resistivity of the AN-FO be controlled; it is further recommended that the operator (3) test to assure continuity of the electric detonator legwire-bridgewire-legwire circuit prior to insertion of the cap into charge or borehole, (4) keep the legwires shunted but not otherwise connected to ground during loading of the blasting agent into the borehole, (5) assure that the borehole is discharged prior to hooking up the detonator leads, (6) assure that he is himself discharged prior to handling the detonator leads, and (7) assure that the blasting cap leads are never carried to the AN-FO loader. The basis and significance of these recommendations are explained.

Jan 1, 1968

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

By Robert M. Becker

A thick-wall cylinder solution applicable to the evaluation of anisotropic elastic parameters is derived for the interpretation of stress relief data. For a restricted class of problems, a special relationship among certain orthotropic moduli yields stress distributions for the plane orthotropic problem that are identical to the corresponding isotropic case. A ring or hollow cylinder with these specialized anisotropic properties subjected to uniform radial loads is one of the problems in this class. Consequently, known stress solutions are used to develop the strains and displacements for a specialized orthotropic thick-wall cylinder under uniform pressures. The results are consistent with anisotropic equations used in the evaluation of in situ rock stresses.

Jan 1, 1968

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968

By N. E. Hanna

An investigation was made of pressure pulses produced by unconfined explosive blasts in underground openings. Four tests were made with TNT or modified amatol charges ranging in weight from 60 to 2,000 pounds; each test involved either single or multiple charges. Pressure-time profiles were obtained using mechanical self-recording pressure gages. The cube-root scaling law for peak pressure was found to be valid within about 1 tunnel diameter; at greater distances, the pressures obtained along direct paths were generally higher than this scaling law would indicate.

Jan 1, 1968

By Eldon C. Pattee

Reconnaisance samples of reported beryllium occurrences in Idaho, Washington, Montana, and Oregon were chemically and spectroscopically tested in a mobile laboratory. The two predominant types of occurrences were green beryl associated with Cretaceous intrusions and disseminated aquamarine associated with Tertiary intrusions. Although the beryllium content of known deposits in the Northwest is too low for economic development at present, total submarginal-grade beryllium resources in pegmatites are estimated to be 570,000 to 1,870,000 tons containing 0.024 to 0.167 BeO. A potential source of 500,000 to 700,000 tons of beryllium-bearing tactite in Idaho and Montana averages 0.033 to 0.080 percent BeO.

Jan 1, 1968

By C. M. Mason

A method for evaluating the relative incendivity of detonating cord in natural gas-air mixtures was developed. The method consisted of firing short lengths of cord in bundles to determine the number of strands per bundle which would ignite natural gas-air mixtures 50 percent of the time in the 45-cubic-foot gallery of the Bureau of Mines. The relative efficiency of a flame quenching agent, potassium acid tartrate (KHT), when incorporated in both the pentaerythritol tetranitrate (PETN) core and the polyethylene sheath, was explored. The effects of sheath thickness, sheath composition, core weight, and core composition were evaluated. The bundle method established a quantitative scale for evaluating the relative incendivity of cords. The relative incendivity determined by the bundle method was then compared with the incendivity of 100-foot lengths of detonating cord when initiated in 8 percent natural gas in the 640-cubic-foot gallery of the Bureau of Mines.

Jan 1, 1968

By J. G. Donaldson

The Bureau of Mines investigated the formation of boron and boron-carbide coatings by vapor-phase reactions. Optimum parameters were determined for hydrogen reduction of boron trichloride and for the fonnation of boron-carbide coatings on graphite by reaction with the depositing boron. At 1,300° C, about 85 percent of the boron was deposited. Tungsten substrates did not react with the boron deposit; other substrates reacted to various extents. The hydrogen reduction of boron tribromide was briefly investigated. Boron carbide was deposited at 1,300° C by adding methane to the boron trichloride-hydrogen feed gas. The chemical composition of the vapor-deposited boron carbide approximated B4C. A method of etching B4C was developed to study its microstructure. When boron was deposited on graphite at 1,500° C, very hard, uniform, strongly adherent coatings of B4C were formed that might be useful in rocket nozzle applications.

Jan 1, 1968

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968