Search Documents

By J. B. Gayle

Because economic and geographic factors have focused particular attention on the use of anthrafines in blends containing Lower Kittanning coal as the low-volatile component, samples from this particular bed were selected for experimentation whenever practical. Carbonizing tests were carried out in accordance with standard procedures, using the Tuscaloosa and sole-heated ovens. Most of the results are in general agreement with those reported by previous investigators. Specific findings are as follows: (1) The effectiveness of anthrafines in reducing coal expansion is such that even highly expanding, low-volatile coals can be carbonized safely with suitable additions of anthrafines and careful control of charge density. (2) Increases in coke size, resistance to shatter, and apparent specific gravity appear to be characteristic for additions up to approximately 15 percent to a fixed base blend. When anthracite of minus-48-mesh size was used and the proportion of low-volatile coal simultaneously increased, these indexes increased only slightly or remained substantially constant. (3) No increase in breeze formation was noted for additions in amounts up to 15 percent. (4) Abradability of coke was increased by additions of anthracite of No. 5 Buckwheat size, but it either decreased or remained sub¬stantially constant when the inert was ground to pass a 48-mesh screen.

Jan 1, 1956

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By B. P. Martinez

In response to a request from the President, the Department of the Interior joined with other agencies in a comprehensive study of the land and water resources of the New England-New York region. As part of this study, chemical engineers of the Bureau of Mines have visited 1,025 mineral-industries plants to inventory the waterborne wastes of mineral origin, discharged by the mineral industries of the New England-New York region. Four-hundred and sixty-two of these plants disposed their wastes to a public sewer of some type, but waste control remains a problem for moat of them. The 1,025 plants are discussed in main industry groups according to their production: Chemical and allied products. Stone, clay, and glass products. Iron and steel and their products (except machinery). Nonferrous metals and their products. Electrical machinery. Machinery (except electrical). Transportation equipment. Miscellaneous mineral industries.

Jan 1, 1956

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By W. H. Oppelt

A small, annular-retort gasifier having a nominal capacity of 40 pounds of lignite per hour was designed and constructed at the Lignite Experiment Station, Grand Forks, N. Dak. The purpose of the investigation was to increase the capacity of an annular-retort gasifier by better temperature distribution in the heating chamber (adjacent to the annulus) and by supplemental internal heating with controlled amounts of air. Correct control of air admission should yield crude ammonia-synthesis gas having a (H2+CO)-N2 ratio of 3. Dakota Star stoker-size lignite was used during the exploratory experimental program. The effects of temperature level and distribution in the heating chamber and of addition of air to the reactor were investigated. Hydrogen - carbon monoxide ratios ranged from 1.9 to 2.5, and (H2+C0)-N2 ratios were as low as 2.9. Hourly gas production ranged from 970 to 2,580 cu. ft., or 62.0 to 164 cu. ft. per sq. ft. of heated surface, or 350 to 940 cu. ft. per cu. ft. of reactor volume. Data from the small gasifier could be readily correlated with those previously obtained in the commercial-scale unit under comparable experimental conditions.

Jan 1, 1957

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

By Joseph Berman

The wolframite mineral series was studied to determine the effect of the FeO - MnO ratio on unit cell symmetry and thermal stability. This work was undertaken to evaluate the analytical procedures now in use for wolframite in scheelite and to aid in the development of improved methods of analysis. Wolframite grains were hand-picked, crushed, and screened; impurities were removed by selective magnetic separations using a Frantz isodynamic separator. The samples were further checked by optical spectroscopic and microscopic examination.

Jan 1, 1957

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By Earl R. Maize

This is the first of a series of reports dealing with development of a method of strengthening bituminous-coal-mine roof. Later reports will describe the progress made with injecting high cohesive and adhesive bonding agents into bedding planes and mine tests of roof strata strengthened by the bonds formed. The concept of strengthening roof strata in coal mines by inserting steel rods in the form of bolts has been widely accepted by the coal industry. The benefits of increased production and safety derived from this type of roof support has more than justified the increased cost of roof bolting. However, not all coal-mine roof structure is amenable to this type of support, and failures occur owing to the heterogeneity and variable character of mine-roof strata.3/

Jan 1, 1957

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957