Search Documents

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953

By O. C. Blade

The use of Diesel fuel continues to increase. In the United States during 1951 over 120,000,000 barrels of Diesel fuel oil were sold. The railroads used approximately 43.5 percent of this volume; industries such as smelters, mines, and manufacturing plants used about 12 percent; trucks, busses, tractors and bulldozers 20 percent; water craft 14.5 percent; and the remaining 10 percent was consumed by gas and electric utilities, the military forces, and oil companies. These figures were calculated from data issued by the Bureau of Mines. 2/ Complete data for 1952 are not yet available, but it is known that by December 1952 over 13 3/4 million barrels of Diesel fuel per month were produced by the country's refineries and by April 1953 the monthly production had increased to 1 4,333,000 barrels.3/ Information on the properties of this type of engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of Diesel fuel oil produced in refineries in this country.

Jan 1, 1953

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By W. L. Crentz

Before Korea was partitioned along the 38th parallel following World War II, the coal fields of South Korea, with the possible exception of the Samchok area, were not considered important to the industrial needs or Japan or Korea. Much of the demand for electric power in South Korea was met by hydroelectric installations north of the 38th parallel. Following cessation of hostilities between Japan and the' Allied nations in 1945, hydroelectric power continued to flow into South Korea from the north until 1949, when the North Koreans severed the power lines into South Korea, thereby forcing that section of the country to depend almost entirely upon coal to generate electric power.

Jan 1, 1953

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954

By J. H. Hild

The Shanton magnetite-ilmenite deposits lie on the east flank of the Laramie Mountains, 43 miles northeast of Laramie, Albany County, Wyo. (fig. 1). The Shanton and other similar deposits in the Laramie Mountains were examined by Bureau of Mines engineers during 1942, 1943, and 1945, and a report2/ describing the results of a dip-needle survey and surface sampling was published in 1946. The Shanton deposits occur in a relatively flat section of the range at altitudes varying from 7,500 to 1,650 feet (fig. la). Prevailing rocks in the Shanton area consist of anorthosite with intrusive dikes of gabbro differentiates and granite. Titaniferous magnetite outcrops in five masses, which are separated at the surface by overburden and anorthosite.

Jan 1, 1953

By Andrew Allan

During recent years underground production for the Pennsylvania anthracite region has reached the lowest output per man per day figure of the last decade and a half. This fact, combined with increased unit costs for labor and material, has forced the market price of anthracite ever higher. Over the years the mines have become deeper, and haulage distances have increased, thus adding to the mining costs. The industry now recognizes the need for new mining techniques to offset increasing costs. The Federal Bureau of Mines, through its Anthracite Research Laboratory, is engaged in a program of underground-mining research in cooperation with anthracite-producing companies to aid in reestablishing the economy of the region by introducing methods and/ or machines that will reduce underground-mining costs and, at the same time, enhance the safety of the workmen.

Jan 1, 1953

By C. C. Popoff

The Dunkleberg district is in the Flint Creek Range of the northern Rocky Mountains, about 45 miles northwest of Butte, Mont. Silver - lead and zinc mineralization occurs over an area 4 miles long from north to south and 1 to 2 miles wide from west to east. Ore in appreciable quantity has been produced, mostly from the Forest Rose group of mines in the southern part of the district. The Forest Rose mine was the largest producer of lead and the Wasa mine, a mile farther south, the main producer of zinc. The total output of ore from these properties during World War II was 113,000 tons, or 98.2 percent of the total recorded production of the district. The Wasa mine was examined by a Bureau of Mines engineer2/ in 1944. Subsequent investigations during 1946, 1947, and 1948 included trenching and drilling Fn the Wasa area and examination of the Forest Rose and other mines.

Jan 1, 1953

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By C. H. Riggs

This report of a petroleum-engineering study of the Flat Rock oil field, Osage County, Okla., describes the geology, reviews the production history, and estimates remaining oil reserves. The Flat Rock field in the southeastern corner of Osage County approximately 6 miles northwest of Tulsa. Okla., was discovered in November 1904. The field was one of the first of many Bartlesville-sand fields developed in eastern Osage County during the early part of the 20th century. Although substantial oil reserves remain in the pressure depleted sands in some parts of the field, their economic recovery by water flooding will require careful consideration of the many factors involved.

Jan 1, 1954

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By H. N. Dunning

A comprehensive research program designed to aid development of new and improved methods for more complete production of petroleum from partly depleted reservoirs is being conducted at the Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla. Water flooding has accounted for much of the petroleum produced by secondary-recovery methods; however, a considerable portion of the crude oil commonly remains in place after water flooding has been terminated. In recent years the possibility of increasing the efficiency of water flooding by using surface-active additives has received wide attention. In general, the results of laboratory research have shown that use of detergents as water-flooding additives will reduce the residual petroleum in porous media (1).3/ Some less extensive field tests have supported this conclusion but have not been entirely conclusive (2). Later studies (3, 4) have given conflicting evidence as to the relative worth of detergent additives for water floods in water-wet (hydrophilic) or oil-wet (hydrophobic or lipophilic) reservoir materials. The results of these studies emphasize the need for a more complete understanding of the fundamental principles involved in displacing petroleum from reservoir surfaces by injected fluids. Accordingly, a comprehensive research program was initiated to investigate the practical and fundamental aspects of detergency in petroleum production.

Jan 1, 1953

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By Irving Hartmann

The record of safety in the use of permissible explosives in United States coal mines has been excellent, due in great measure to the persistence with which research has been carried on in the Bureau of Mines, to the development of permissible explosives, and to the cooperation of mine operators and workers in using permissibles in a recommended manner and in the effective though gradual replacement of black powder and other nonpermissibles. The demand for increased rate of coal production, changes in mining conditions and minim methods, and introduction of new mining machinery have resulted in modified or new blasting practices. To keep abreast of these developments the Bureau of Mines conducts investigations under actual mining conditions at the Experimental coal mine near Pittsburgh, Pa. Several years ago an extensive study was complete to determine conditions under which the allowable charge limit for permissible explosives per shot hole might be raised from 1.5 to 3 pounds without undue risk of gas or coal-dust ignitions. As a result of the study, this increase in the charge limit was authorized under certain specified conditions in 1948,5/ greatly facilitating production schedules.

Jan 1, 1954