Search Documents

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By A. Holder

A major mud push occurred on the 870 m production level, scraper drift block cave at Dutoitspan diamond mine in November 2011, during which it is estimated that more than 4 400 m3 of mud engulfed the west cave. The production level was successfully evacuated during the mud push with no loss of life or injury to personnel, thanks largely to mine employees being well trained in and adhering to on-mine mud rush evacuation procedures. All access to the west cave was lost as a result of the mud push. Clean-up operations are currently under way to regain access to the production level, to establish the extent of damage to scraper drifts and equipment, and to evaluate what remedial works may be required to resume production. The magnitude of the Dutoitspan mud push necessitated a detailed investigation into the key contributing factors leading up to the incident, which are discussed in this paper. Mud rush mitigation measures in place on scraper drift block caving operations at Dutoitspan, Bultfontein, and Wesselton diamond mines in the Kimberley area are critically reviewed. Recommendations are furthermore made for enhanced mitigation based on mud rush risk profiles derived for different production areas in these old scraper drift block caves. Keywords mud push, mud rush, scraper drift, block cave, mitigation factors, risk profiles, risk management structure.

Jul 1, 2013

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By Hans Ehdwall, Erling Strandon, Friedrich Steinhäusler, Victor A. Leach

INTRODUCTION The basis for any measures in radiation protection is the quantitative assessment of the radiation exposure. Due to the extensive requirement in health physics manpower and related cost it is necessary to develop certain criteria regarding the necessity of monitoring and the selection of population groups to be monitored. Depending on the overall objective of the particular programme, the specific requirements for the measurement of atmospheric levels of radon, thoron and their daughters for practical radiation protection purposes differ significantly for those in the case of research applications, such as use of data for epidemiological studies. As part of the OECD-NEA Programme on Radon Dosimetry and Monitoring Task Group 1 reviewed available models for lung dosimetry in the case of inhalation of radon 222, radon 220 and their daughters (James et al., 1981). Using defined reference atmospheres for underground- and open-pit mining conditions as well as for dwellings, normalized conversion factors were calculated for the mean bronchial dose (mGy) per Working Level Month exposure (WLM). Task Group 2 discussed the features and adequacy of the Working Level (WL)-concept as a physical correlative of the absorbed lung dose and its limits of confidence and accuracy (Johnson and Leach, 1981). The WL-concept was found acceptable for radiation protection purposes provided that modifying factors like particle size, unattached fraction and respiratory minute volume did not cause the effective dose equivalent per WLM as calculated by either the James-Birchall or Jacobi-Eisfeld lung models to be more than 50 % above that given by ICRP of 0.01 Sv/WLM. For application in epidemiological studies the WLconcept is considered acceptable if the calculated absorbed dose to the tissue does not vary by more than 50 % (at the 95 % confidence level) from that given for defined reference conditions. In the following, objectives and requirements for the measurement of radon, thoron and their daughters are discussed for operational health physics routine and special research applications according to the scheme outlined in Fig. 1.

Jan 1, 1981

By Wilbur Nelson

THE year 1924 showed even less drilling in Kentucky and Tennessee than the preceding year. The operators in this section, however, are anxious to resume development work and are only waiting for a higher market for crude oil before starting such a program. In Kentucky, during 1924, 1605 wells were completed, the combined initial daily production of these wells being 25,599 bbl. Of the total number of wells drilled 1176 were oil wells, 61 gas wells, and 368 were dry holes. The average initial production of the oil wells was 21.8 bbl. per well. In Tennessee, 28 wells having an initial daily production of 1199 bbl. were completed during 1924. Of these, 3 were oil wells, 6 were gas wells, and 19 were dry holes. The initial production of the three oil wells was 400 bbl. Of the total number of wells drilled in Kentucky in 1924, 73 per cent. came in as producing wells; and of those drilled in Tennessee, 10 ½ per cent. came in as producing wells and 20 per cent. as gas wells. In Tennessee, during 1924, wildcatting dropped off considerably and only about one-half as many wells were drilled as in the preceding year; in Kentucky, on the other hand, there was only a slight curtailment in drilling, there being 1943 wells drilled in 1923 as against 1605 in 1924.

Jan 3, 1925

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

During the past eight years a vigorous drilling campaign resulted in large increases in the reserves of both copper and silver-lead-zinc ores.As a result the Company initiated an increased production programme.Some major capital works have been completed, others are in progress and more are needed to achieve the proposed daily throughput of 14,400 tons. The increased ore potential justified a copper refinery which has been constructed at Townsville. The increased production rate achieved to date, combined with improved techniques and greater mechanization, is assisting the Company to combat the general inflationary trends caused by increased costs for labour and materials.INTRODUCTION"Today we are armed with better weapons in our fight for lowered costs and greater efficiency, but we must not flag in our efforts to improve." Such was the resolution expressed by Mr. K. B. Gross, then General Manager of the Company, in his review lecture delivered to the First Ordinary Meeting of The Australasian Institute of Mining and Metallurgy at Mount Isa on 18th August, 1952. This present review of the period 1952 to 1960 records our efforts to fulfil this resolution. At the th:ne of Mr. Gross's statement,copper production was commencing in earnest. Although the importance of Mount Isa's copper orebodies was well recognized, the major discoveries which led to Mount Isa's emergence as Australia's premier copper mining and smelting operation were not known. These ore discoveries and their subsequent development are the major factors which warrant a further review of the Company's progress.The increased magnitude of the Company's operations is illustrated on graphs of Tons of Ore Treated (Fig. 1), Metals in Products (Fig. 2), Water Consumption (Fig. 3)...

Jan 1, 1961

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Sheila E. Daniel

"Since 1989, the Mine Environmental Neutral Drainage Program (MEND) has sponsored research into ways of reducing the environmental impact and financial liabilities associated with Acid Mine Drainage from tailings and waste rock. Toward this overall objective, Kilborn was contracted to review the use and applicability of passive treatment systems for acid mine drainage.Experimentation using passive systems to treat acid mine drainage has been ongoing since the early 1980's in North America. Passive treatments are generally considered an attractive alternative to active lime treatment, since they require minimal human involvement, no power, and only seasonal or periodic care and maintenance after establishment. Most attractive is that initial capital cost to implement a passive treatement system is generally low to moderate. Ongoing operating costs are similarly low when compared to active treatment systems.Passive treatment systems currently used, or under investigation to treat acid mine drainage include: anoxic limestone drains, aerobic wetlands, reed bed wetlands, compost wetlands, microbial systems and bioabsorption systems. These wastewater treatment systems utilize the chemical, biological and physical removal processes that occur naturally in the environment to improve wastewater quality, including: oxidation, reduction, coagulation, adsorption, absorption and precipitation; microbial activity; and, gravity aeration and dilution. The rates at which these processes occur determines the loading which can be treated and the effectiveness of the system.The results of our literature review will be summarized, and insight provided into the applicability of passive systems to treat acid mine drainage from Canadian Mines."

Jan 1, 1995

I take it the character of addresses to conventions, should, following precedent, avoid details, and treat subjects rather from a philosophical point of view so far as they will permit.In the subject about to be treated on, an endeavour will be made to find here we stand as regards the past, in order that we may the better, hope to look correctly in the direction to be followed.It may be assumed that the main object of the Institute is to forward mining interests and the ways in which engineers can aid those interests are many. If all of us were to try to follow many of those interests we should become like" jacks of all trades and masters of none". Mining engineering is consequently subdivided, all are necessary to the common end, and it is on one of those divisions I have undertaken to address you. The subject or steam pumping is a large one, and I regret, not having received such longer notice as would have enabled me to do better justice to the subject, and more respectful regard for yourselves. I must, however, under the circumstances, crave your generous consideration, and hope the topics mentioned may furnish material for discussion and future papers of far more value than this one, Ind.eed, the subject is so illtimately and historically associated with mining that if treated on its merits would be highly interesting or could be made so in more capable hands.

By Martin P. Corriveau

It is not news to anyone in the mining industry that federal action in the prevention and abatement of air pollution has seriously affected the industry both directly and indirectly. It is the purpose of this paper to review how the development of federal action is directly affecting the coal mining industry's number one customer, the fossil-fuel-fired steam generating power plants and, consequently, the industry itself indirectly. In essence, Public Law 84-159 of 1955 as amended by the Clean Air Act of 1963 and its revisions in 1967 and 1970 progressively tightened federal coordination and management of air pollution control programs throughout these United States. The Environ- mental Protection Agency (E.P.A.) set up to direct the programs was charged to establish National Air Quality Standards, Standards of Performance for New Stationary Sources, and National Emission Standards for Hazardous Air Pollutants.

Jan 1, 1973

By L. P. Teas

ALTHOUGH 1927 in the Arkansas-Louisiana territory will probably pass into history as a year of small profits and little new production, nevertheless during this period two large gas fields were developed; two new oil fields were discovered, and two new oil horizons, hitherto of minor Annual Production in Millions of Barrels FIG. 1.-PRODUCTION OF NORTH LOUISIANA AND ARKANSAS BY FIELDS FOR 1926 AND 1927. importance, were developed; In spite of the "hard times" some of the leading, supply houses did more business this year in this. district than in any year since 1920.

Jan 1, 1928

By E. L. Estabrook

THE production of crude oil in Wyoming rose to 44,290,010 bbl. in 1923 and declined, during 1924, to 39,295,030 bbl., a decrease of about 11 per cent. The Salt Creek field supplies 75 to 80 per cent. of the production. Pipeline runs from the Salt Creek field reached a maximum in November, 1923, at a daily average for the month of 116,437 barrels. During 1924, the gas pressure in Salt Creek has declined rapidly and the production dropped to about 60,000 bbl. per day. Part of 'the decline during the last few months was due to lack of power to pump the wells. The electric-power plant of the Midwest Refining Co. did not begin to deliver current until the middle of December, by which time several hundred wells were off production. The cold snap in December, which brought, the temperature down to 30° below zero on the 17th, tied up operations almost completely and the average production for the month was only 49,545 barrels. As more wells are being pumped and the number of dead wells reduced, the production is rising and was up to 61,000 bbl. during the last week of January. A further increase is expected as the weather becomes warmer. The production of Salt Creek, by months, during 1924 is given in Table 1. TABLE 1.-Total Monthly Production, Average Daily Production and Number of Producing Wells in Salt Creek during 1924 TOTAL PRODUCTION, DAILY AVERAGE, NUMBER OF MONTH BARRELS BARRELS WELLS January 3,523,647.40 113,666.05 919 February 3,074,916.67 106,031.61 929 March 2,977,095.14 96,035.32 950 April 2,811,110.22 93,703.67 987 May 2,858,842.04 92,220.71 1,024 June 2,649,752.57 88,325,09 1,092 July : 2,697,829.36 87,026.75 1,153 August 2,624,371.84 84,657.15 1,213 September 2,281,219.04 76,040.64 1,274 October 2,073,961.42 67,000.84 1,313 November 1,722,050.09 57,401.67 ~ 1,335 December 1,535,903.78 49,545.28 1,352 Total 30,831,699.57 84,239.61 1,352

Jan 3, 1925

By C. Babcock

This Bureau of Mines report considers some equations for mine pillar design from 1833 to the present. Most of the equations are of essentially the same kind, using pillar width to height relationships. The effects of end constraint and test volume size, that were implied in some of these early equations have received special emphasis in recent years. Experimental testing in the laboratory throughout the period given has been on prisms or cubes of coal or rock. Most of the present concepts have been known since about 1912. Wilson has recently emphasized the effect of end constraint in his confined core concept, but a number of other earlier relationships have indicated an awareness of the effects of constraint as well.

Jan 1, 1981

By D. Malhotra

Gold and silver ores are generally leached in weak cyanide solutions for recovery of precious metals. However, pretreatment of refractory ores requires flotation to concentrate the precious- metal minerals. Also, flotation is a common concentration technique for recovering precious metals as byproducts in sulfide-mineral flotation circuits. The present paper reviews current plant practice and future challenges for precious metal recovery.

Jan 1, 1999

By J. R. Giegerich

"IntroductionMINING operators in common with other operators are confronted today with two serious problems, shortage of experienced workmen and rising costs. The following review of practices at the Sullivan mine of The Consolidated Mining and Smelting Company of Canada, Limited, outlines certain measures that have been responsible, during recent years, for minimizing the effect of these two problems. The paper is divided into three main sections:( 1) Training programmes and job studies( 2) Improved mechanization and equipment( 3) Large-scale methods of operationTraining Programmes and Job StudiesJob TrainingJob training courses were introduced at Cominco immediately after the last war and proved to be a great benefit to the operations. There were three courses given, Job Instruction Training, Job Safety Training, and .Job Relations Training. These were spread over a period of two years and were taken by all operating supervisors and some key operators.The courses were introduced by a trained instructor from the British Columbia Department of Labour. This man trained twelve of our employees as instructors by giving them an intensive one-week course. Similarity between the three courses was such that the instructors trained in the first one were very readily trained for instruction in the two succeeding courses."

Jan 1, 1952

By A. M. Alfantazi, R. R. Moskalyk

Over the years, improvements have been made in the recovery of nonferrous metals, including improvements in the areas of mineral processing, pyrometallurgy and hydrometallurgy to extract cobalt as a byproduct from host minerals containing mainly nickel, copper and associated precious metals. At present, the technological emphasis is on solvent extraction coupled with electrowinning (SX-EW) for lateritic sources of supply within the Southern Hemisphere, such as in Australia and New Caledonia. Although sulfide-bearing ores, such as those found in Canada and Russia, will serve as a viable long-term source for cobalt, a ubiquitous metal, the future trend is anticipated to be in the implementation of compact and efficient SX-EW facilities that apply state-of-the -art innovation with environmental compliance This paper serves to collate the known practices for the recovery of market-grade cobalt by means of electrowinning from either an aqueous sulfate medium or chloride medium after upstream leaching, solvent-extraction and solution-purification procedures. For completeness, other commercial production techniques for the recovery of cobalt as a sulfide or oxide product are included in the summary of current cobalt processing practices.

Jan 1, 2000

By Frederick Clapp

INTRODUCTION - SCOPE OF DISCUSSION There has hitherto been no systematic effort to make public the available information on petroleum in South America and the object of this paper, therefore, is to broadly discuss the subject as it pertains to South America as a whole, endeavoring to collect in readable form what is known regarding individual fields. This article is not intended to exhaustively discuss individual fields, or to solve the many complicated problems regarding petroleum and natural. gas in the various republics, since those necessitate years of study and work by petroleum geologists, engineers, financiers, and drillers. Neither. can the reader expect absolute accuracy in all statements, since this is impossible at the present time. The writer has, of course, attempted to be correct in all cases, but in a review involving so many countries and extending over so many, phases of the subject, it is to be expected that some errors will have crept in.

Jan 10, 1917

I. C. WHITE, Morgantown, W. Va. (written discussion *).-The writer's conclusions with reference to the possibility of finding commercial deposits of petroleum in Brazil were published in 1908 in the Final Report of the Coal Commission of Brazil.1 Since this volume is not generally accessible, and the author has nothing to acid thereto, the following quotation found on pages 243-7 may prove of interest: The Possibility of Petroleum Deposits in Brazil "The writer has often been asked to express an opinion as to the possibility of finding petroleum in commercial quantity in Brazil. "The question is one that does not admit of an adequate answer except for the regions visited by the writer, which as already stated, include only, a portion of that great territory, and only the southern portion of Brazil; namely, the states of Rio Grande do Sul, Santa Catharina, Paraná, and a few rapid excursions across São Paulo, and Minas Geraes, as well as the brief visit to Marahú in Bahia. "That the sedimentary beds of the Brazilian Permian once held some petroleum is attested by the evidence of the Iraty black shale which gives off the characteristic odor of this substance from São Paulo to Rio Grande do Sul.

Jan 1, 1918

By Gerald Sherman

Asbestos ore is hard, well intersected by free fissuring but not completely enough to avoid heavy secondary blasting, and is a more valuable ore than usual for caving. These factors have resulted in deviations from standard caving practice in details but not in principles.

Jan 4, 1950