Search Documents

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By Yongqiang Liu

Background For refractory gold ores with high carbonate contents ! Acid pressure oxidation ! High acid consumption (if low sulfur content) ! Low oxidation efficiency due to CO2 in autoclave ! Problems with slimy precipitates (gypsum, etc.) ! Alkaline pressure oxidation ! Difficulty in fixing arsenic ! Low gold dissolution due to iron hydroxides/oxides coating ! High reagent costs Summary ! Carbonate and sulfide minerals had similar floatability across the pH range tested (5 - 12) using sodium oleate as a collector; ! Thioglycollic acid or citric acid depressed the flotation of pyrite but could not depress chalcopyrite when used alone; ! Combination of thioglycollic acid and citric acid had a much stronger depressive effect, and the mixture depressed chalcopyrite as well as pyrite between pH 8 and 11 without affecting the flotation of calcite and dolomite; ! Calcite could be separated from chalcopyrite and pyrite; dolomite could be separated from pyrite but not from chalcopyrite under the tested conditions.

Apr 1, 2005

By S H. Marshall, H Hutcheson

Conventional batch cell and FASTFLOT pilot plant studies of reverse flotation of coarse marcasite and pyrite (100 - 400 μm) to reduce the sulphidic sulphur content of a rutile concentrate, were undertaken. The batch cell experiments found no significant improvement in sulphur removal with acid wash and copper activation of marcasite and pyrite. Batch cell trials also identified potential difficulties of conventional mechanical cell plants operated at 40 per cent w/w solids. The FASTFLOT 250 B-2 pilot plant trials indicated that with a 0.6 - 0.7 per cent w/w feed sulphur content, target product grade can be met on a routine basis by a three-stage FASTFLOT plant floating coarse marcasite and pyrite. The trials found that 150 g/t PAX dosage and 15 minutes conditioning time are adequate reagentisation for 40 per cent w/w solids feed to the FASTFLOT plant.

Jan 1, 1998

By Xinyang Yu

The flotation of diaspore, kaolinite, pyrophyllite, illite and the diaspore-kaolinite mixture were studied with a new cationic organosilicon quaternary ammonium collector entitled QAS222. The acting mechanism of the collector with the four minerals was analyzed by Zeta potential measurement and FT-IR spectrum analysis. The results indicate that the QAS222 was effective in the reverse flotation of the diaspore-bauxite mixture of different Al2O3 -to-SiO2 mass ratios (A/S ratio) at an optimum pulp pH of 11. The potentials of the four minerals increased when they were conditioned in the QAS222 solution; however, the potentials of the three aluminosilicate minerals increased faster than that of the diaspore, especially at pH>9. Furthermore, they were positive in a wide pH range, indicating that QAS222 has a strong adsorption on the surface of the aluminosilicate minerals and thus that these minerals can be floated. The FT-IR spectra analysis further indicates that, besides electrostatic adsorp-tions, formation of the hydrogen bond and ammonium absorptions, chemical adsorptions occur between QAS222 and the aluminosilicate minerals, which allow for the QAS222 to be strongly adsorbed on the aluminosilicate minerals. However, these reactions between QAS222 and diaspore at pulp pH=11 are weaker than those of the aluminosilicate minerals. Thus, surface adsorptions cannot be formed effectively, resulting in reduced floatability.

Jan 1, 2010

By P. Oliveira, A. Peres, A. Silva

"The decrease in iron content and increase in contaminants grade, associated with greater participation of compact and semi-compact materials, has impacted the recovery of a mechanical cells flotation circuit in the Iron Quadrangle, Brazil. The recovery decrease in the flotation stage motivated the current conventional flotation circuit reevaluation seeking alternatives to restore the recovery, without affecting the final concentrate quality parameters, with low investment. Sampling, chemical characterization of samples, bench scale flotation experiments, and mass balances were conducted. Analysis of the results showed opportunities to improve the circuit performance. The stages prior to the flotation circuit changes were: rougher, cleaner, recleaner and scavenger. In the previous configuration, recleaner was operated as cleaner scavenger and the iron grade in the scavenger concentrate was 23%, representing 38% of the new feed. After the circuit change, the circulating load was reduced from 38% to 15% and the iron content was upgraded to 42%, resulting in increased residence time. The iron content in the global tailings of the concentrator was decreased from 10.9% (year of 2013 average) to 10.2%, representing gains in both mass and metallurgical recoveries.INTRODUCTIONRegarding plant practice, the year 1972 represents a landmark for the concentration of iron ores in Brazil. VALE started up 28 units of WHIMS (wet high intensity magnetic separators) at the Cauê plant in Itabira, each one producing 1x106 t/year of concentrate. Later 17 WHIMS machines were commissioned at Conceição. During the 80’s decade of last century, changes in the ROM required the addition of a cleaner flotation stage to decrease the silica content in the pellet feed.The first company to use reverse cationic flotation as the only concentration operation of iron ore was SAMARCO (start up in 1977). Since 2015 flotation has been utilized at VALE in Itabira as major concentration process, magnetic separation acting as scavenger stage.The Jones matrix type WHIMS were manufactured for decades under patent by KHD Humboldt Wedag. After the expiration of the Jones patent, Eriez Magnetics took the world leadership regarding WHIMS manufacturing. The Brazilian branch of Eriez is Inbras. Based on plant practice experience at the Fabrica concentrator, the Brazilian company Gaustec was established (RIBEIRO and RIBEIRO, 2010) and is now present in different countries. The mega sized WHIMS GHX-1400 (18.000 Gauss, gaps smaller than 1.5 mm) were developed to face the challenge of huge throughput required by iron ore processing (Ribeiro et al, 2017)."

Jan 1, 2018

By M. Prasad, A. K. Majumder, T. C. Rao

The depletion of high-grade phosphate ores is bringing about a search for a suitable, economically viable technique that con process the abundant low-grade phosphate reserves. About 75% to 80% of the world's low-grade phosphate reserves are associated with carbonate gangue that is not amenable to treatment by the simple techniques of physical separation. The processing of sedimentary dolomitic/calcareousphosphate ore has numerous problems, including similar surface properties of the carbonate and phosphate. Two-stage reverse anionic flotation of carbonates (dolomite/calcite) has appeared to be a promising separation technique ,for the removal of carbonates from sedimentary rock phosphate. In reverse fatty-acid anionic flotation, the depression of phosphate mineral with orthophosphoric acid produces satisfactory results for calcareous as well as dolomitic phosphate ores from several locations of sedimentary origin.

Jan 1, 2000

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By Chris Howell

PotashCorp?s Aurora phosphate mine, in Beaufort County, NC, operates four low pressure boilers and four high pressure boilers to meet its process steam requirements. Maintaining these boilers is critical to meeting production demands. Processing phosphate ore into phosphoric acid requires large amounts of sulfuric acid and steam. Ore is mined from the phosphate deposit with large bucket excavators after 9 to 30 m (30 to 100 ft) of overburden is removed. The phosphate ore is mixed with water to make a slurry that is pumped to the mill. Elemental sulfur is burned in the presence of air to make sulfuric acid. This process is highly exothermic and boilers produce steam while cooling the process. The phosphate ore is reacted with sulfuric acid and the resulting products are refined into different grades of phosphoric acid for fertilizers, feed stock and food additives. Plant operators at the mine were challenged with boiler feed water that was high in silica and other contaminants. As a result, boiler operations were experiencing difficult, labor-intensive operations and equipment deterioration. This resulted in higher operating costs and diminished processing performance. The facility was operating an aged boiler feedwater pretreatment system that included warm lime softening followed by pressure filtration and a cation/anion/mixed bed demineralizer system. The demineralizer required frequent regeneration and chemical usage was high and costs were difficult to predict. Depressurized well water (DPW water), used for plant utility water and boiler makeup, is very high in silica, in the range of 60-70 ppm. Silica can form scale at pressures below 600 psig. Above 600 psig, silica starts to volatize, carrying over with steam to potentially form deposits on downstream equipment and processes. Mine officials decided to upgrade the boiler feedwater pretreatment system to a state-of-the-art reverse osmosis (RO) membrane system. This new system, which started up in March 2009, has improved operating performance and reduced water consumption and overall operating expenditures.

Jan 1, 2011

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 2.4-m (96-in.) diam vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subse¬quently, a field test was conducted in a Colorado oil shale mine during which two 2-m (79-in.) diam fans were reversed. The data obtained indicate that reverse performance characteristics depend on the blade angle and the hub-to-tip ratio. The quantity in the reverse mode ranged from 30% to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1987

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

Reverse sensitivity is a critical issue for all extractive activities. Extractive industries can only establish in the location of the particular resource sought to be extracted. Avoiding a location near sensitive activities (such as residential activities) may, therefore, be more difficult for extractive industries, than for other industry (such as dairy factories).   This paper focuses on the following matters: +        principles to be derived from case law, +       district and regional council approaches managing reverse sensitivity effects, and +        avoiding, remedying or mitigating reverse sensitivity effects in the future.

Jan 1, 2006

By B Small

CSA Mine, named after the nationalities of the mines first owners being Cornish, Scottish, Australian, is one of Australia’s deepest and highest-grade copper mines. A combination of the modified Avoca method and shrinking was a standard practice where production rings were fired against and bogged to waste fill. This method resulted in dilution and involved rehandling of waste material to refill the bogged stopes in the Western region and the QTS Central. The introduction of pre-charging blastholes using a wireless initiating system (WebGen™) has enabled CSA to design and fire stopes in reverse. This involves the use of a pre-charged Temporary Rib Pillar (TRP) against the waste fill material in a previously mined stope. The temporary pillar reduces dilution and improves conventional bogging as material is blasted towards the drawpoint rather than towards the waste fill material. Additional drill, prep and blast re-work is reduced or completely removed as rings can be charged prior to, in conjunction with, or after, charging of the slot. This is a safer practice as the charge crew spend no time working adjacent to a brow or open void. A TRP trial was conducted in the western orebody at CSA. The risk of exposure to a brow or open void while charging underground, and the bogger rehandling of waste material was successfully eliminated. Once reverse stoping was established in modified avoca stopes at CSA, two TRPs were implemented in challenging ground conditions in the QTS Central region. The TRPs were utilised in a retreating four-way intersection to extract a central diminishing pillar to close the level out. The ore recovered in this stope provided 5 per cent of CSA’s copper for the year. Without pre-charging with a wireless initiating system, two 5 m pillars totalling 6936 t of ore at 7 per cent either side of the stope would not have been recovered. CSA has implemented the practice of reverse stoping in modified avoca stopes using TRP for ten stopes since the successful trial. The development of additional blasting techniques enabled by precharging with wireless initiating systems is currently underway in the QTS North orebody at CSA Mine.

Mar 29, 2023

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By Larry M. Southwick

Processing of ores to recover metals usually generates large amounts of waste materials, such as rejects from concentrating operations, tailings from leaching and slags from smelting. These wastes often contain substantial amounts of iron and other metals, recovery of which are often considered to be of commercial value. Earlier versions of this paper investigated a number of processes built to recover iron from a variety of copper processing residues. This paper will extend that coverage to residues from nickel/cobalt, aluminum, asbestos and oil shale processing and coal plant fly ash. Products of interest are iron, ferroalloys, magnesium and aluminum. While none of these processes achieved long-term commercial success, their efforts cover the gamut of problems that must be addressed in treating dirty and difficult materials to recover generally low-value products. An Adept is an alchemist who can create a Philosopher's Stone, which could transmute base metals into gold. In 1701 in Berlin one Johann-Freidrich Böttger, a nineteen year old apothecary's apprentice, told King Frederick I that he could discover how to make the Stone. He failed and fled Frederick's wrath to Poland. He failed again, and King Augustus II threw him in jail. Then, in 1709, he discovered instead the secret of making Dresden china, certainly a more practical search. His failures in alchemy led to the nickname Adeptus Ineptus.

Jan 1, 2004

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Ramon Fraga Resende

O distribuidor é o último equipamento revestido de refratários em contato com aço líquido e que pode afetar a qualidade do produto. Nesse equipamento, a massa de trabalho é responsável por proteger o revestimento de segurança e evitar a contaminação do aço. Apesar das preocupações em relação ao “pick up” de hidrogênio e consumo de gás, as massas “spray” tem sido uma tecnologia dominante para o revestimento de distribuidor na América do Sul. Nos últimos 20 anos, outras tecnologias entraram no mercado com o objetivo de reduzir a necessidade de água e de gás e aumentar a disponibilidade de distribuidor. Embora essas tecnologias apresentem algumas vantagens, quase 80% das usinas siderúrgicas da América do Sul ainda usam massas “spray”. Isso se deve principalmente aos benefícios como flexibilidade, baixo custo, baixo consumo e alto isolamento térmico. Este trabalho tem o objetivo de discutir as principais vantagens e desvantagens das massas disponíveis no mercado.

Oct 30, 2017

By Haysler Apolinário Amoroso Lima, Francisco Pereira Netto, Vladnilson Peter de Souza Ramos, Bruno Nery Stoco, Gilvan Nascimento de Souza

Em um mercado dominado por tijolos de Al2O3-MgO-C, o revestimento de trabalho de panela de aço monolítico e CarbonFree se apresenta como uma tecnologia disruptiva para um novo patamar de qualidade do aço e eficiência energética. O presente estudo relata a motivação para a implementação do primeiro fundo de panela de aço com revestimento monolítico concretado in situ no Brasil, e apresenta uma análise preliminar dos resultados e vantagens observadas. Uma panela da Ternium Brasil foi revestida com refratários de Al2O3-MgO, e colocada em operação sem nenhuma necessidade de ajuste na operação da aciaria. A partir dos dados de processo e das medições a laser, calculou-se o desgaste do revestimento, bem como verificou-se a garantia de qualidade nos aços IF (interstitial free) e a maior preservação na temperatura do aço durante o refino secundário.

Oct 1, 2019

By Danilson Gonçalves de Melo e Silva

O balanço de energia realizado em um forno de aquecimento de tarugos apresentou rendimento de 53%. A maior perda energética estava relacionada ao sistema de refrigeração dos skids, cujo valor calculado foi de 18%. Objetivando minimizar tais perdas, estudou-se a utilização de um novo tipo de revestimento refratário para esta região. O fabricante de refratários apresentou uma estimativa de ganho de 62%. Desta forma, a VBR planejou um teste para validar a eficiência do refratário proposto. Neste teste, o produto foi instalado em uma viga auxiliar. Esta viga foi instrumentada, e foram registrados dados de vazão, pressão e temperatura do fluido de refrigeração (água). Objetivando comparar estes valores com o material convencional anteriormente instalado, outra viga com as mesmas características (dimensões e posição no forno) também foi instrumentada. Posteriormente, foram feitos os balanços de energia em cada viga para quantificação das perdas de energia térmica. Os resultados encontrados mostram uma redução de 92% da perda térmica relacionada ao sistema de refrigeração dos skids. Considerando a eficiência do forno de 53% e a redução de 92% da perda térmica, estima-se uma economia de R$ 1.200.000 por ano.

Sep 25, 2017