Search Documents

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By E. S. Noe, D. S. Arnold, C. E. Polson

Reactors of today and tomorrow require a high uniformity of their fuel elements despite the wide variety of uranium raw materials from the far corners of the earth. To meet these quality standards metallurgists have been working to design production methods capable of yielding reactor feed materials whose maximum impurities are specified in parts per million, whose physical limits are expressed in thousands of an inch, and whose density variations are less than 1 pct. Such requirements are necessary to maintain normal neutron flow in the atomic reactor and to insure that the isotopic content of the feed material is maintained within narrow limits. Uranium ores and concentrates are produced in many sections of the world, including the Belgian Congo, South Africa, Australia, Canada, and the Colorado Plateau of the U. S. Ores from many of the larger deposits are relatively low grade, and these are concentrated near the mine site before shipment to refining centers, but high grade ores may be shipped directly to refineries.

Jun 1, 1956

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

By N. Tsuneyama

Sumitomo Metal Mining Company has been operating Waelz Kiln at the Shisaka Works for 12 years to recover zinc and lead from electric arc furnace (EAF) dust. To increase the capacity and cut down the operating cost, some improvements have been carried out resulting in the capacity of 60,000 t/ y of EAF dust as compared with 32,000 t/ y in 1977. The current capacity is equivalent to 20% or EAF dust generated in Japan. The number of workers has been decreased by the introduction of an automatic control system, and the productivity per worker is now twice as much as 10 years ago. This paper will describe the progress of the operation at the Shisaka Works after the previous? paper reported in "Zinc' 8 5? and summarize the status or EAF dust recycle in Japan.

Jan 1, 1990

By S. M. Taghavi, M. Halali

This paper investigates the possibility of zinc oxide production from zinc ore concentration residues, and also the effect of temperature, time and depth of bed on waste materials reduction percents. The results obtained show a significant increase of the reduction percent as a function of time and temperature. With increasing in depth of bed, reduction percent will decrease. Maximum zinc oxide percent in products was 93.5%.

Jan 1, 2004

By Sinha NH

ICI Australia and CSIRO have developed a novel process for extraction of zirconia from zircon sands. The two stage process involves a high temperature step and a wet chemical processing step. A pilot plant has been operating since November 1985 at CSIRO Division of Mineral Chemistry, Port Melbourne and construction of a full scale plant isplanned at Kwinana, WA.The plant has a high degree of flexibility and is capable of producing high purity zirconia up to about 99.99% and withinspecific particle size ranges. The products are being marketed by the joint company, 2-TECH Pty Ltd.

Jan 1, 1986

By Aureo D. V. Machado

An experimental study to obtain zirconia powders (ZrOz) from carboxylate zirconium solutions followed by hydrogen peroxide stripping and precipitation, has been carried out. Zirconium carboxylate was prepared by solvent extraction from a chloride aqueous phase using magnesium carboxylate as organic phase. The variables examined in the precipitation reaction were: Temperature: 25 - 90 ?C ? H202= concentration: 0.3 - 5% wt/wt - pH: 1 ? 9 Organic/Aqueous ratio (1/1) and reaction time (30 minutes) were maintained at constant levels. The optimum results (98% precipitation) were achieved at 25 °C, 5 % wt/wt H202=, and pH = 5. The precipitates were composed of large amorphous aggregates (<I00 micrometers). After calcination for 1 hour at 1000 OC, monoclinic ZrO2 with a large variation in particle size (1 -100 micrometers) was obtained.

Jan 1, 1991

By KAGAN BENZESIK, Onuralp Yücel, Mehmet Bugdaycı, Ahmet Turan

ZrB2 and B4C are one of the most significant advanced ceramics. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, Carbon black, B2O3 were used as starting material to produce ZrB2-B4C powders by SHS. Also Mg powder was used as the reductant. The reaction mixtures (approximately 100 g) were mixed thoroughly 15 minutes in a turbula mixer and charged into Cu crucible and compacted. W (tungsten) wire was placed at the top of copper crucible and the reaction realized by passing current through the wire. After initiation, a highly exothermic reaction became in a self-sustaining mode and propagated throughout the SHS mixture. The samples were characterized by using AAS and X-Ray Diffraction.

Jan 1, 2016

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By Lee W. Saperstien

At the heart of the mining process are a number of basic and fundamental tasks whose regular and repeated performance constitute the mining cycle. As will be discussed presently, these tasks are the basic components of the mining system. Section 9, Production Operations, provides the mine designer and engineer with an understanding of these tasks and with sufficient design principles to allow this person to create an efficient mine system. This section is meant to be an introduction and adjunct to subsequent sections that describe specific mining systems. However, sufficient design information is included here for the independent design of mine systems that may not be described elsewhere or for subsequent verification of existing designs. For the purposes of this section, mining subsumes excavation; thus this material applies to any excavation process. Accordingly, this section is written in general enough terms to include both surface and underground mining. It may be used also for civil engineering excavations that often involve the same steps. Obviously, the actual procedures undertaken in any specific mining system will appear to be very different from those taken in any other system. This is certainly true when comparing surface with underground methods. Yet the fundamental principles are often the same. This segment is written to explicate the basics. Wherever appropriate, the section will suggest the differences between the application process to surface or to underground mining.

Jan 1, 2008

By F. Ames Smith

Offshore oil and gas production operations have moved from water depths of about 50 feet in 1948 to the present record depth of 340 feet. Although mobile drilling rigs are widely used for exploratory drilling, most development drilling and production operations have been conducted above water from the decks of fixed, bottom-founded platforms. Increasing water depths have caused problems associated with design and construction of these platforms and with laying of pipelines, but not so much with other activities. After a platform is installed, drilling, production, and maintenance operations are similar to those onshore and are relatively unaffected by water depth. Events of 1968 indicate that offshore production may soon extend into much deeper water. These events include leasing of Santa Barbara Channel acreage in water depths over 1500 feet, and the successful drilling of a wildcat well in 1300 feet. Designs have been developed for platforms suitable for installation in water over 600 feet deep, and studies suggest they may be used in some areas to water depths of 800 to 1000 feet. Buoyant towers can probably support above-surface platforms in water 1000 feet and deeper. Although the cost of either of these platforms will be high, once installed they will permit relatively low-cost development drilling and production operations compared with estimates for subsea production systems. In some cases, savings in development drilling costs alone could pay out the platform investment.

Jan 1, 1969

By Jose A. Jimenez

"Mining operations generate an enormous amount of data that is difficult to organize, analyze and act on. These data require an extremely broad range of experts to investigate and manage the cross-disciplinary information. The data collects in paper files, diverse databases, historians, stand-alone applications, and excel files. This collection of sources represents everything from monthly, weekly, or daily inputs to real-time feeds or sporadic unscheduled entries. With the operational complexities ever increasing and fewer engineers per mine, an efficient operation is becoming more and more challenging. Engineers are typically burdened with data collection, clean up, and administrative efforts leaving very limited time for engineering assessment and/or optimization analysis. Often optimization becomes limited to the analysis of equipment uptime through existing field automation systems. A great portion of the field data is tucked away in historians seldom reaching those engineers who might leverage the data. Few mine operators have the time or budget to re-architect their operations data collection or management practice, so solutions must enable improvements without requiring expensive or time-consuming implementation. This presentation highlights examples where the aforementioned challenges are addressed using a solution framework designed to enable: 1) data integration and connectivity, 2) monitoring and opportunity recognition, and 3) engineering workflow automation. The initiative extends the concepts and success proven in the automation market segment to all disciplines across the mine operations. INTRODUCTIONThe mining industry by its very nature spends a great deal of its capital on equipment maintenance and replacement. In addition, periodic shutdowns due to equipment failure are typically very costly in terms of interrupted operations. Keeping mining equipment running at peak performance and avoiding costly shutdowns can make a huge difference in the overall return from mining operations. Today, information can be make available that can go a long way towards spotting equipment issues and permitting timely intervention to avoid costly unplanned shutdowns. That said, gathering all of the information from numerous points on many different pieces of equipment necessary to enhance overall equipment effectiveness presents its own daunting issues."

Jan 1, 2016

By P. Mageau-Béland, È. -M. Proulx, M. -C. Patoine

Over the past six decades, Hatch has helped several industrial processing facilities in debottlenecking their operations, allowing them to produce more with the same equipment, to reduce and even eliminate expenditure investments, or to increase the return value of their expansion projects. These successes result from the application of a proven analysis approach that can be applied to any industrial facility. A five-stage methodology is discussed and demonstrated with a specific example of a nickel concentrator optimization study. The first stage is an observation stage which allows to meet key actors at the plant, develop mutual understanding of problems, understand operating philosophy, and efficiently collect large amounts of operating and maintenance data. Following is a data compilation stage during which data is analyzed over a representative time period to identify parameters that significantly affect the production, to evaluate data reliability and to define the focus of the upcoming analysis. Quantitative metrics are defined using statistical tools such as pivot tables, histograms, percentiles and MDR (Maximum demonstrated production rate during 3 to 7 consecutive days). Then, the production bottlenecks are identified by a thorough analysis of the facility’s control philosophy, process throughput, equipment capacity, availability, downtime causes, and interaction between components of each circuit. Understanding the maintenance practices and frequency of planned shutdown is also critical to this analysis. Opportunities for improvement are identified in collaboration with the operation, maintenance and engineering teams, ranked as a function of their impact on the bottlenecks and prioritized. The final and most critical stage involves engagement with the plant stakeholders, namely the operators and the maintenance staff members, to present the results of the analysis and obtain their participation in the implementation of the solutions. The benefits of the case study translated into: 10% production capacity gain, improved maintenance planning and avoidance of several million dollars of investment.

Jan 1, 2016

"Chairman: Mr W. S. GALLAGHERRapporteur: Professor A. M. STARFIELDPapers:Long-term mine production scheduling by G. C. S. BurneAn application of linear programming to investment analysis by A. ErlandssonOptimizing medium-term operational plans for a group of copper mines by M. Splaine, D. C. Atkinson, W. Davison and L. SmithThe simulation of underground stoping and transport operations in gold mining by F. H. Touwen and N. C. JoughinProduction planning is a subject that lies at the interface between the computing centre and mine management. Discus¬sion during this session was thus largely concerned, directly or indirectly, with communication between computing and mining personnel, and as such was relevant to the symposium as a whole.Mr A. Weiss set the tone of this discussion by referring to `user-orientated systems&apos;. He congratulated Mr Burne in this regard, pointing out that his long-term production scheduling program, as a computer system, was similar in approach to the manual system it replaced, and was therefore easily understood by planning engineers. He asked whether the schedule engineer had his &apos;hands on&apos; the system, to which Mr Burne replied that the engineer did in fact spend several days running alternative schemes through the computer. Mr Weiss commented on the advantage of having terminals on site for this sort of engineer-computer interaction. He also commented on the flexibility of Mr Burne&apos;s approach to scheduling and how preferable this was to a one-step optimization package. This was brought home by a question from Mr H. D. Small: Mr Burne&apos;s program sometimes found it necessary to temporarily halt an advancing face, and he asked whether the logic of the program could be altered to avoid this (e.g. by suitably slowing down the rate of face advance). Mr Burne replied that it was in fact easier for the planning engineer to sort this problem out manually. The way in which the computer results were presented made it particularly simple for the production engineer to see how to avoid or remedy a stopped face.On the technical side, both Mr Weiss and Mr H. M. Wells questioned Mr Burne on the handling of grade control by his program. From answers by Mr Burne and his colleague Mr K. H. Thomson it emerged that a spot-check on grade every now and then was all that was necessary at Mufulira, and that the idea of actual grade control was more a question of short-term than of long-term planning."

Jan 1, 2014

"Chairman: Professor C. O. Frush Rapporteur: Mr A. C. SchmidtPapers:Planning of underground copper mining by J. K. Williams, L. Smith and M. P. WellsLinear programming models of copper leach and solvent extraction plants by W. P. C. Duyvesteyn, J. R. Cutland and J. R. L. RusselPlanning and forecasting stope production by D. W. Kappes and P. F. X. Moussett-JonesA proposed method of dynamic ore reserve assessment for a caving system of mining by A. F. Spinks and S. P. NicholsThe initial point made by Mr L. Smith in presenting his paper was that the planning aid outlined in the preprint was neither sophisticated nor complicated. However, it was a system which worked and was a very real way in which the computer was being used to assist miners, in particular, who at the present moment have very little experience in the use of computers.Mr Smith apologised for the fact that the editors of the paper had eliminated all reference to &apos;time&apos;. This was very unfortunate because the essence of the system was that it saved time, which was one of the main points made in the paper.The operations being planned by this means cover the Rokana orebody which is a stratiform body mined by open stoping.The planner has to decide how much ore to mine from each base in each time period of his plan, that is, from three to four months hence to a year ahead. Normal procedure is for the planner to have discussions with the underground manager on some of the information he requires. The sort of information needed is (i) tramming limits for each face, (ii) extraction and grade factors, (iii) the present status of mining operations so that the planner knows where to start the new plan, and, (iv) details of any other mining consider¬ations that need to be incorporated in the plan.The objective at this point is to produce an initial plan for discussion purposes. All the information required comes from one sheet per stops and shows, inter alia, the stope identifier, the length along strike, the ore tonnage, the copper and cobalt grades and, finally, the extraction and grade factors.The program itself, among many other things, checks the data for validity, compatibility, completeness and credibility and prints error messages accordingly. Output from this system is in the form of a summary of production from each face, as well as giving the figures of ore reserve depletion. This summary indicates which slopes are to be mined in this time period, the original survey grades (copper and cobalt), the estimated production grades, how much is to be mined from each stope and the copper and cobalt production accordingly."

Jan 1, 2014

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996