Search Documents

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

By Neil Styler

This paper presents an analysis of measurements of inter-burden deformations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock extending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Chu E. Ho

Current methods of determining jet grout column diameters are highly empirical and site specific, and do not take into account the jet hydrodynamics and soil parameters explicitly. A theoretical model which describes the jet excavation mechanism is introduced in this paper, with the aim of providing an improved prediction tool that can be used in jetting design. The model is based on the assumption that the velocity distribution in the cutting jet is equivalent to that of a free jet with boundaries corresponding to the dimensions of the cavity excavated in the ground. The shape of the cavity formed depends on the erosional properties of the soil and jet expansion is limited by the resistance at the jet-soil interface. The model predicts that the limit of jet penetration is reached when the average dynamic pressure at the jet tip becomes equal to the ultimate soil bearing resistance. The reliability of the model, evaluated using results from four case histories of jet grouting field trials, is within ±15%.

Jan 1, 2006

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By R. Peter King, Claudio L. Schneider, Reiner Neumann

Predicting the liberation spectra that is produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.

Jan 1, 2003

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By Jeffrey W. Nelson

Predictions of creep closure for periods ranging up to more than 1,000 years are needed for designing a radioactive waste repository in a salt formation. Such long-term predictions must be based on the use of laboratory and field test results extrapolated by numerical modeling. Laboratory test results are presented which show highly variable creep behavior for salts from different sites as well as salts from the same site. Comparisons of measured creep closures against predicted closures are presented for two deep boreholes in Louisiana salt domes and for an exploratory shaft and drift in southeastern New Mexico bedded salt (WIPP). These data illustrate the significant uncertainties involved in long-term closure predictions and indicate the critical need for site-specific, in situ closure measurements over extended periods of time for repository design.

Jan 1, 1984

By A. Pavlidis

This paper investigates variations of lignite quality attributes with geostatistical methods. The study focuses on lignite from the Southern Field in the Greek province of West Macedonia. The targeted quality variable is the ash water-free content (AWF). A geostatistical model is constructed based on data from 480 drillholes (approximate drill hole spacing of 250m). For each drillhole, the vertical average of the AWF is calculated. The coarse-grained AWF is then modeled as the superposition of a trend surface and fluctuations. The spatial dependence of the fluctuations is modeled by means of the experimental variogram. Kriging estimators are used to determine the AWF values on a rectangular grid, and the uncertainty of the estimates is calculated. Implications of the analysis for the variability of the produced lignite are discussed, and recommendations for additional drilling are proposed.

Jan 1, 2006

By McNabb KE, Ward B, Dyer G

Roof conditions at Southern Colliery, the second longwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 in thick roof beam either bonded or detached, with either a 2 in or 5 in overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

Roof conditions at Southern Colliery, the second Iongwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 m thick roof beam either bonded or detached, with either a 2 m or 5 m overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By P. H. Morris

The profile of a delta formed by fine-grained mineral processing wastes, disposed of as aqueous slurries by subaerial deposition from a pipeline, has a significant bearing on the volume that is available for waste and water storage in a given containment structure. Earlier field data and laboratory experiments suggested that mine waste delta profiles could be predicted with high levels of accuracy using data from small-scale laboratory deposition tests. The relationships between the profiles of full-size and laboratory-model deltas were analysed using the principles of kinematic similarity and a recent theory of delta formation based on engineering hydraulics. Measured profiles of full-size and model coal-mine tailings deltas are compared and the prediction of full-size profiles discussed. It is shown that the data-derived laboratory-model deltas are insufficient to allow accurate prediction of full-size delta profiles. Initial slope data or other, equivalent data for the full-size delta are also required

Apr 1, 1996

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991

This paper presents the near-field rock damage owing to production blasting in limestone quarry in the western region of Japan. The study's purpose is to learn the mechanism of crack development due to blast vibration. In this study, blast vibration's magnitude was expressed with peak particle velocity (PPV) which was obtained based on seismographs recorded database. In attempt to pursue a research's purpose of this study, there were two considerable interests: near-field blast vibration propagation and prediction, and crack observed and prediction. Furthermore, with regards to considerable interest of the study, there were three essential aspects which were challenged, such as: monitoring and interpretation of seismic wave propagation in a rock mass near large explosive charge of production blast scale, measurement of blast rock damage in adjacent to blasthole, and determine critical value of PPV which may produce significant rock damage. In order to determine precision critical PPV, understanding correlation between rock damage with vibration level is firstly important to be done. This paper also discusses how to measure, detect and quantify near-field blast vibration and blast rock damage in adjacent to blasthole.

Dec 6, 2010

By A. D. Davis, C. J. Webb, A. Heriba

Introduction The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, the regulatory agencies and the general public. The disposal of an additional several hundred million tons of spent ore from heap-leaching operations is planned in the western United States during the next decade, and this amount could increase if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills of South Dakota. The criterion for offloading spent ore was set by the South Dakota Department of Environment and Natural Resources at 0.5 ppm weak acid dissociable (WAD) cyanide. South Dakota's nitrate offloading limits vary for each mine, depending on ore type and other factors. Concentrations of nitrate in the leachate from spent ore depositories could be the result of conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from the blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete oxidation (Johansson and Persson, 1970). Another likely nitrate source is the degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate. A third possibility may be leaching of background nitrate from soil or rock. Objective The primary objective of this research was to investigate laboratory procedures for predicting nitrate concentrations in effluent after the disposal of spent ore at heap-leach gold processing operations. Laboratory tests were performed to define the concentrations of nitrate and nitrite in leachate as a function of time. Sources and species conversions were examined by investigating the nitrogen contributions from cyanide neutralization and from blasting with ammonium nitrate/fuel-oil (ANFO) explosives. Ore processing at cyanide heap-leach facilities Gold mines in the northern Black Hills of South Dakota normally use the following steps in their heap-leach cyanidation processing: Blasting. Surface gold mines in the Black Hills use ANFO explosives (approximately 95% ammonium nitrate and 5% fuel oil). Field evidence and studies show that explosives often fail to ignite or burn completely in shot holes. One reason is that ammonium nitrate absorbs moisture readily, which reduces blast efficiency. Ferguson and Leask (1988) cited a study conducted at the Fording coal mine in southeastern British Columbia. In that study, the total nitrogen released to surface and ground water was estimated to be about 6% of the slurry explosives. However, Ferguson and Leask (1988), in a later analysis of water quality near coal mines in the Kootenay coal fields, indicated that this is likely an overestimate of the nitrogen release. Mines that used ANFO explosives in dry conditions released 0.2% of the nitrogen from blasting. Cyanidation. At surface gold mines in the northern Black Hills, cyanide species from heap leaching can be classified into free cyanides and simple ions, weak complexes, moderately strong complexes and strong complexes (Scott and Ingles, 1981). Degradation of cyanide and disposal of spent ore. Methods of destroying cyanides include hydrogen peroxide oxidation, natural degradation and evaporation, water leaching and alkaline chlorination. Hydrogen peroxide is used to oxidize cyanides in the northern Black Hills mining area. The hydrogen peroxide oxidation reaction forms cyanate, which can hydrolyze to form ammonium and carbonate ions. After formation of ammonia or ammonium ion, further oxidation to nitrite (NO2-) and nitrate (NO3-) can occur. Spent tailings from gold processing in the Black Hills normally are disposed of in tailings facilities constructed in nearby drainages. Infiltrating rainwater with a typical pH of about 5.6 is an additional component introduced into the spent ore after disposal. Methods Field sample collection. Spent ore samples were collected from conveyor belts (or other convenient points) at heap-leach mines by personnel from the South Dakota Department of Environment and Natural Resources. The samples were placed in black plastic bags that were contained within 5-gal buckets and sealed to prevent exposure to ultraviolet light. The samples had a minimum head space to limit evaporation and contact

Jan 1, 1997