Search Documents

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By G. Swiatnicki, w. Chruscielewski, T. Domanski

INTRODUCTION The inherent errors of simple passive track detectors /SPTD/ used for estimation of exposure to the radon daughters /RnDP/ amount to about 30% /Do75/ while for active detectors only reach about 3 - 4% /Ph78, Du79/. The large error inherent in SPTD is the result of strong dependence of its calibration coefficient on the equilibrium Rn RnDP in the vicinity of detector /0r80/. Nevertheless the SPTD shows many advantages and seems to be very useful for to the estimation of individual exposure of miners to RnDP /Do81a/. For this reason the investigations are undertaken to improve SPTD so that it might provide information about the equilibrium Rn : RnDP during exposure. If the equilibrium would be known then one could use a suitable calibration coefficient yielding a better precision of the measurement. So far, some investigations of the improved type of SPTD have been conducted. One was based on the concept of using the so called diffusion barrier permitting to differentiate the tracks originating from Rn and RnDP /Fr77/. Such improved detector has been named a passive differentiating track detector /PDTD/. However, own investigations have shown /Do81b/ that this type of detector cannot provide precise informations about equilibrium Rn : RnDP. For this reason the investigations of the new idea of PDTD have been carried out. The new model presented below is based on the use of the absorbers of alpha particles. THEORETICAL CONSIDERATIONS The first variant of the concept is as follows: The differentiating detector consists of two portions of detective foil /track detector/ but only one is covered with an aluminium absorber. Thickness of the absorber is carefully selected so that only RaC' particles /7.7 MeV/ can pass the barrier. The second portion of the detective foil records all alpha particles originated from Rn and RnDP i.e. works like a SPTD. The scheme of such a detector, the so called two-fields passive differentiating track detector /PDTD-2/ is shown in the Fig. 1. It is possible to introduce a parameter that can characterize the equilibrium Rn RnDP, namely, the so called track density ratio /TDR/. The definition of this parameter for the considered type of detector is TDR2 = D1•D2-1. One can expect the simple proportion to hold: [ ]

Jan 1, 1981

By J. W. Merks

"The accuracy of a measurement on minerals and ores can be assured by applying suitable and unbiased procedures but its precision is a function of the number of primary increments and their mass, the number of lots per consignment or samples per shift, and the number of measurements on analysis fine samples.Experimental data will be used to show how the variance components for sampling, sample preparation and analysis contribute to the total variance on which precision statements for the final measurement are based. This type of experiment should not only form part of quality control programs at mines and smelters, but also underly the criteria on which the design of manual sampling regimes and mechanical sampling systems for bulk solids and slurries should be based.Sampling systems and regimes can only be adjusted and optimized if the variance component for each step in a quality evaluation process is measured. Knowledge of precision characteristics lies at the core of effective loss prevention and control programs."

Jan 1, 1985

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By C. J. Konya, A. Konya

"Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industry, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, the optimization of explosive load, as well as prediction methods for the environmental affects for the technique of Precision Presplitting. BACKGROUND Methods of controlled blasting in which a smooth, stable wall could be blasted have been an important consideration since blasting in mining and construction has begun. How can one use an explosive, with its massive energy and power, to break a non-homogenous rock without causing backbreak, poor walls, or deviations in the wall over large distances? The blasting industry has known for a long time that blasting ‘high benches’ would result in better walls and less backbreak. However, this was not a sufficiently controlled technique for critical projects, such as the Niagara Power Plant. This was one of the main challenges Hercules Powder faced when they began the project. In order to achieve this, they used a new tool in the explosive engineer’s toolkit, presplitting. The presplitting done on the Niagara Power Project utilized 1 ½” x 8” (38mm x 203mm) 40% gelatin dynamite in 2 ½” (63.5) diameter boreholes. This was done on multiple levels with benches between 12 feet to 52 feet (3.6m to 15.8m) with a total powder factor of 0.75 pounds/cubic yard (0.45 kg/m3). The spacing on these holes ranged between 18 inches to 24 inches (0.46m to 0.61m), center to center (Langfors & Kihlstrom, 1973). The strange aspect of this project was that this “lightly loaded” closely spaced row was fired before the production blast, yet this project produced some of the best walls seen at that time directly from blasting. In today’s blasting industry, presplitting is a more common way to produce smooth, stable high-walls for both the construction and the mining industry. Today, explosive loads for traditional presplitting is generally measured in pounds per foot (kilograms per meter) and typically ranges from 0.30 lb. /ft. to 0.5 lb. /ft. (0.45 kg/m to 0.75 kg/m). MECHANICS OF PRESPLITTING When analyzing a blasting process like the Niagara Project, many wonder how did that work when normally confining a charge would cause cratering and increased backbreak. Since then, presplitting mechanics have been studied extensively. It has been shown in many models that presplitting is not achieve through the collision of shockwave, but by gas pressure in the boreholes. In addition to models and finite element simulations, this has been proven full scale using Pyrodex, a propellant, to create a presplit plane with no shock wave present (Konya, Dean Barrett, & Smith Jr, Presplitting Granite Using Pyrodex, A Propellant, 1986)."

Jan 1, 2017

By Anthony J. Konya, Calvin J. Konya

Mine sites and construction projects have faced problems with blasting a smooth back wall. This lead to safety concerns with slope stability and rock falls from the walls. Decades ago Dr. Calvin Konya began a special type of blasting called “Precision Presplitting”. This form of presplitting used relatively light loads based on the rock type being blasted. The explosive loads were estimated for each rock type and adjusted as blasting progressed. This current research project also determined a new equation for prediction of the ground vibration from one type of presplitting and compared it to vibration from production blasting.

Jan 1, 2016

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

Precision surface mining is increasingly occupying a significant role in open pit mining. Improvements in technology now allow continuous surface mining of material well above 140 MPa (20 300 psi) efficiently and cost effectively when compared to drilling and blasting/primary crushing methods. These include the elimination of the use explosives and primary crushing, the ability to precisely extract the ore from the waste, or separate ores of varying chemistry and mine thin seams and non-homogenous orebodies cost effectively. In addition, precision surface mining extends the useful life of a mine by extending the mine boundaries. It can expand production capacity in existing mines and is particularly cost effective in greenfield start-up mines. Precision mining techniques result in higher percentage recoveries. This paper reviews several of these techniques for the Terrain Leveler« surface excavation machine (SEM), and shows their impact. Vermeer's current approach to precision surface mining is utilisation of the T1255 Terrain Leveler SEM. Several units have been proven in round-the-clock, seven day operations throughout the world. Among other innovations are design simplicity, stability, maneuverability, rear-mounted tilting drum and top-down cutting. The impact of these items are discussed in more detail in the paper. After a detailed analysis of the importance of machine availability on overall mine performance, Vermeer has extended its equipment line to include a direct-drive option for its T1255 Terrain Leveler SEM. In addition, improvements in dust suppression are presented. While the T1255 Terrain Leveler SEM is of optimum size and cost in small and medium sized mines, Vermeer has recognised that larger mines require larger machines with increased capacities. Vermeer will prototype the T1655 Terrain Leveler SEM later this year. Specifications of this machine and up-to-date preliminary results are presented. A discussion of the role of each machine size and driving mechanisms are included. Finally, the next stage in Vermeer's providing solutions to the surface mining community will be described - a continuous loader. The impact on current mine planning is presented using a detailed computer program developed for studying the impact of loading techniques and higher production rates on mine plan optimisation.

Dec 6, 2010

By Douglass D. Donald

The New Jersey Zinc Co. successfully holed through a 2 ½ -mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8 x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial additional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine.

Jan 9, 1958

By Frank Foote

IN recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansen1 has re-viewed the literature to 1935. More re-ently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have con-firmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice con-stants of the silver-rich alpha solid solution in the homogeneous range and the neigh-boring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data.

Jan 1, 1940

By Charles E. Joachim, Christo V. Lunderman, Charles R. Wdch

The U.S. Army Engineer Waterways Experiment Station (WES) recently conducted a series of precision-scale water shock experiments which consisted of the detonation of several 8-gram, 10-gram, and 12-gram spherical explosive charges. The charges were fabricated from NAX 2000 Primasheet explosive and were center-detonated. Commercial tourmaline crystal water shock sensors were used to measure the induced pressure fields in the water. The measured water shock waveforms and related parameters from the precision-scale experiments were in general agreement with data from larger-scale experiments.

Jan 1, 1998

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By I Auranen, J Raatikainen

IMA Engineering (IMA) and Mine On-Line Service (MOLS) companies have used on-line sensors for analysing ore and waste rock in mining for more than 25 years. Today IMA on-line sensors are used in various stages of the mining process including on-line analysis of drill cores, drill chips, ore and waste in loader bucket, ROM ore analysis on belt conveyor belt and in bulk ore sorting and in slurry analysis in concentrators. During years of extensive field experience and testing we have found that the waste rock dilution and ore losses create much larger economic and environmental losses than has been previously recognized. According to our studies the main reason is limited number of analysis already in exploration when drill cores or drill cuttings are used in block modelling. The same happens in production because too few and biased samples from benches are used to estimate the ore grade. Much more than today estimated amount of waste enters the mill and considerable volumes of ore losses happen at the same time. The ore grade on the benches and in muck piles is averaged and “homogenized” with averaged and biased samples. These are the main root causes of waste rock dilution and ore losses. Sensor based preconcentration can be the remedy to waste rock dilution and ore losses. This presentation will show examples of the use of on-line sensors in preconcentration when analysing ore and waste rock in drill cores, drill cuttings, on conveyor belt and in bulk ore sorting. Waste rock removal in preconcentration has direct effect on energy consumption in crushing and grinding and chemicals in concentrator. In concentrator waste is separated and goes to tailings pond, however, preconcentration directly reduces the volume of the tailings. In our presentation we will cover cases in base metals and in gold mines.

Nov 10, 2020

By J. A. King, D. R. Weir, P. C. Robinson

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration. Minipiloting of the preconcentration and oxidation stages of the Porgera flowsheet are described. The influence of these processes on subsequent recovery of precious metals together with the technical and economic necessity of concentrate pretreatment prior to oxidation are discussed.

Jan 1, 1987

By Thomas J. Lien

Granitic Pegmatite deposits are the chief source of commercial feldspar, micas, lithium minerals, tantalum-columbium, beryl, and certain types of kaolin. The output from pegmatite mines in the United States is small compared to other mineral products in terms of bulk or value, and much of it comprises only minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in our domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. In recent years, realizing the potential importance of the pegmatite minerals, the U.S. Geological Survey, the United States Bureau of Mines, several state Bureaus of Mines, and a few private companies have carried on extensive programs of pegmatite studies in the New England and southeastern states, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California. Currently, some of the pegmatite minerals such as micas and spodumene are selectively separated by the flotation process. To a lesser extent a few plants are selectively floating feldspar and quartz. Much of the credit for the above progress goes to the fine work done by U.S. Bureau of Mines (1), and companies such as Foote Minerals (2). Additional research efforts by the New Mexico Bureau of Mines (3) has successfully demonstrated selective separation of micas, beryl, spodumene, lepidolite, microlite, quartz and feldspar from a complex Pegmatite containing all these minerals. Since the nature of the mineralization of various valuable components of a pegmatite deposit is such that selective separation of some of these can be carried out at a coarse size using the Heavy Media Separation technique, it was felt that such a system should be investigated for selective preconcentration of their minerals. It was also felt that of all the :MS systems available, the DYNA WHIRLPOOL (DWP) device which allows a close control and adjustment of specific gravity should provide a means of achieving the above goal. Once the desired preconcentration of one or more of the pegmatite mineral assemblage is achieved, the available selective flotation techniques should provide effective recovery of various minerals into marketable products. This paper presents technical and economic aspects of selective preconcentration of some of the pegmatite minerals followed by selective flotation to produce marketable products.

Jan 1, 1978

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

By T BoBo, D La Rosa, P Cameron

Efficient pre-concentration using natural and induced deportment starts with effective blast design. Leveraging these characteristics using Size-Based Grade Engineering® techniques requires detailed understanding and measurement of the particle size distribution (PSD) of the Run of Mine (ROM) ore. In turn, blasts must be designed to optimise fragmentation for the pre-concentration method. To be successful, fragmentation outcomes must be predicted and measured as part of the blast design process to account for the response ranking of the rock mass. The upgrade achieved using Size-Based Grade Engineering® methodologies will rely on the proportion of feed that reports to the screen undersize, so particle size distribution of the feed stock is of paramount importance if the potential benefits are to be achieved and maintained. Measuring actual fragmentation in the ROM ore and comparing with predictions allows the modification of subsequent blast designs to optimise fragmentation for pre-concentration scenarios. Automating this process can deliver significant increases in productivity and mine site profits. This paper discusses the importance fragmentation plays in Size-Based Grade Engineering® and explores technologies and methodologies used to measure it, consistently ensuring the best outcomes.

Nov 10, 2020

By Jieliang Wang, Shiwen Yi, Zhao Cao, Peng Zu

Bayan Obo ore contains mainly bastnaesite, monazite and associated iron, fluorite, calcite, dolomite, barite, and trace amount of columbite. Due to its complex mineral compositions and similar mineral properties, it is difficult to separate and obtain rare earth and fluorite concentrates with high purity by conventional magnetic separation and flotation. In this paper, a stepwise magnetic separation process comprised of wet permanent magnetic separation (PMS), wet electromagnetic separation (EMS), and superconducting magnetic separation (SCMS) was proposed to pre-concentrate iron, rare earth, and fluorite minerals from Bayan Obo ore. The results showed that iron, rare earth, and fluorite preconcentrates with high purity and low impurity content could be achieved, which might be helpful to shorten the technological process and improve the separation efficiency for the subsequent flotation of iron, rare earth, and fluorite minerals.

Sep 15, 2020