Search Documents

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Robert Cluff

The Campo Morado precious-metal-bearing, volcanogenic massive sulphide district occurs in a Lower Cretaceous felsic volcanic sequence in a northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. The deposits belong to a low-sulfidation, volcanogenic massive sulphide system formed in a subaqueous environment, and are of the siliciclastic type. Most are on the flanks of felsic domes or in adjacent basins and many are associated with heterolithic volcaniclastic rocks. The Reforma and possibly the El Rey massive sulphide deposits are interpreted to be overturned, and the Naranjo, El Largo, and Estrella de Oro deposits and the El Profundo occurrence to the south are upright. The G9 deposit and the La Lucha and San Rafael occurrences are in an over-thrust plate further to the southwest. In several of the deposits, zinc, lead, silver, and gold are concentrated near the stratigraphic top, and copper is concentrated near the stratigraphic base; copper also is concentrated in replacement bodies near the top of some domes. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Gold and silver occur in argentian gold, and silver also occurs in tennantite/freibergite and galena. Underlying stockwork zones contain disseminated and vein quartz, pyrite, chlorite, and ankerite, with locally abundant chalcopyrite and/or sphalerite. Exploration since 2004 has enlarged greatly the El Largo and the high-grade G-9 deposits, and slightly enlarged the El Rey deposit. The cumulative in situ massive sulphides for the Reforma, Naranjo, El Rey, El Largo, and G9 deposits exceed 45 Mt.

May 1, 2006

By Tage Jepsen

El presente análisis muestra el proceso de lixiviación y precipitación en la extracción del cobre en el Perú utilizando las aguas de la mina Quiruvilca. La alimentación de las mismas permitirá transformar el mineral en sales secundarias de cobre, fácilmente solubles y por ende, dar una mejor distribución del mismo hacia los canales de precipitación.

Jun 20, 1954

By R. W. Smith, D. Clare

The removal of metals from an acid mine drainage (Leviathan Mine, Alpine County, California) water by precipitate flotation was investigated. The Leviathan waters vary from about pH 4.0 to pH <2.0and contain from about 2,000 to about 12,000 ppm SO42-.The main multivalent metals present in solution are Fe, Ca, Mg, Al and Mn. Both Cu and Co are present in small amounts. The pH was adjusted with lime. The collector used was either sodium oleate or tall oil. The sodium oleate was used as a function of pH to establish optimum flotation conditions and the tall oil was used only at the optimum pH. Dow Froth 250 was used as a frother. In some test additional Cu was added to the system. Excellent recovery of Fe and Cu were achieved at optimum pH. The process achieves results comparable to precipitation and filtration without as much problems with screens blinding because of less material to filter.

Jan 1, 2004

By CorrOa de Araujo A, Salum MJG

The treatment of mining and metallurgical liquid effluents is becoming, everyday, a necessity felt by these industries. Physical-chemical and chemical methods for treating such effluents are generally necessary whenever heavy-metals and other toxic compounds such as cyanide are present. The present paper discusses the use of precipitate flotation as an alternative physical- chemical method that can be applied for the treatment of effluents containing heavy-metals (mainly zinc and cadmium) and cyanide. Examples of laboratorial scale applications on real effluents are given. In both cases precipitate flotation was able to reduce the concentration of toxic components of the effluents at a very high removal rate, generating a solid waste that can either be disposed, re-used or recycled. A cationic collector - dodecylamine hydrochloride - demonstrated to be the best choice of surfactant for the two systems investigated. Sodium sulphide and dithizone were selected for the precipitation of the zinc bearing effluent whereas a copper salt was preferentially used for precipitating cyanide in a form adequate for its recycling envisaging the use of an AVR (acidification - volatilisation - regeneration) technique.

Jan 1, 1993

By W. Nazarewicz

The introduction of continuous papermaking in the early 1800&apos;s was the beginning of the industry as we know it today. Since that time, the majority of the paper produced has employed an acid process. However, in the mid 1960?s, European producers began a transition to an alkaline papermaking process. Early European mill conversions to alkaline papermaking begun in the 601s, accelerated during the 1970&apos;s influenced by the dramatically higher cost for OPEC energy as well as the high cost of fiber and imported filler clay.

Jan 1, 1986

By Rasik H. Raythatha

Calcium carbonate is perhaps the most widely used mineral in the world. With total consumption of all calcium carbonate exceeding over 25 million tom per year, within this class of filler, a relatively smaller segment of precipitated calcium carbonates (PCC) is often misunderstood as a commodity product and bundled in the same category as ground calcium carbonate. However, each material has a distinctly digerent role and characteristics. Precipitated calcium carbonates are used to influence specific performance in a specific application whereas ground calcium carbonate is used primarily to reduce cost in many applications. In this paper, attempts are made to demonstrate the role of nano-fine-PCC in improving shear-thinning characteristics of common and specialized sealants and automotive underbody coating and how such "nano-particle" cal- cium carbonate properties can be exploited to process PVC plastics while reducing overall cost. We also review the role of precipitated calcium carbonate as "nano" material and why it must be viewed as a specialty additive.

Jan 1, 2003

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott&apos;s Bingham Canyon copper precipitation plant, one of the world&apos;s largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott &apos;s Bingham Canyon copper precipitation plant, one of the world&apos;s largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By Jingtao Wang, Xiaoyu Han, Jun Bao, Wei Hou

Lightweight stainless steel has widely potential applications in many fields, such as automobile, ship, submarine manufacturing and aerospace. The properties of lightweight stainless steel are significantly affected by the precipitating behaviour of second phase particles. In this paper, the precipitating behaviour was investigated by XRD, DSC in the process of heating and thermodynamic calculation combining the Miedema’s and Chou’s model. The XRD results indicate that there are five types of phases in lightweight Fe–Mn–Al–C–N stainless steel: ferrite, FeAl, AlMn, AlN and Mn4N. The DSC results show that the precipitating temperature of FeAl, Mn4N is 1260, 1031 °C, respectively, corresponding to the thermodynamic calculation. Besides, The DSC measurement reflects the precipitating temperature of AlMn and austenite is 934 and 600 °C.

Mar 1, 2018

By C. O. Tarr, G. V. Smith, R. F. Miller

METALLURGISTS have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 2050°F.1 This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In 1935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0.1 5 per cent carbon steel that had been in senrice for about 26,000 hr. at a temperature of about 1100° to 1200°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7o0°C. (1290°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, obsenred graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 1200°F. Unstressed samples of 0.60, 0.86 and 1.14 per cent carbon steels graphitized almost completely in 360 hr. at 1200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at 1200°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from 1600°F. and by cold-working prior to annealing. In creep tests of normalized o. I 5 per cent carbon steel killed with 2.5 lb. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at 1000°F. under a stress as low as 15m lb. per sq. inch.

Jan 1, 1944

By Alexandre Monteiro

Alumina precursor powders can be precipitated from aqueous solutions, using hydrothermal decomposition of urea to deliver base homogeneously to the system. Primary particles agglomerate early in the process, generating a wide size distribution. The presence of a polymeric surfactant such as polyacrylate can suppress or delay agglomeration, reducing particle size and narrowing the size distribution. The stabilization of commercially available a-Alp03 powder with polyacrylate was studied, investigating the effects of polyacrylate molecular weight, ionic strength and temperature. The effect of aluminum concentration, polyacrylate molecular weight and urea concentration on the precipitation of alumina precursors in a sulfate- urea system in the presence of polyacrylate/polyacrylic acid was then studied. The hydrolysis kinetics were followed, and particle sizes were determined. Precipitates were further characterized using energy dispersive spectroscopy. The particle characteristics are discussed in terms of the process conditions.

Jan 1, 1994

By Fuqiang Zheng, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Xiaoming Qu

MxTi3-xO5 is the main titanium-bearing mineral in the titanium-bearing electric furnace slag (TEFS), which is produced by direct reduction-electric furnace smelting process with vanadium titanomagnetite concentrate in Panzhihua-Xichang region of China. In order to effectively utilize the titanium resource in TEFS, the thermomechanical analysis and conditions for the growing up of MxTi3-xO5 grain were investigated, which emphasized on the effects of CaF2 and cooling rate on the crystallization of MxTi3-xO5 in the melting process. The mineral phase and morphology of titanium-bearing slag were determined by XRD and electron microscope technique, respectively. The results indicated that the average grain size of MxTi3-xO5 grown up from 30 to 92 lm and the area fraction of MxTi3-xO5 reached about 66% from 61% under the conditions of 5 wt% CaF2 and cooling rate at 1 °C/min.

Mar 1, 2017

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By Fathi Habashi

Precipitation of a metal from an aqueous solution of its salts by another metal is known as cementation, because the precipitated metal is usually cemented on the added metal. This phenomena was once described by the alchemists as "transmutation," when they dipped a piece of iron in a solution of copper sulfate and the iron was coated with a layer of metallic copper. The process can be predicted in terms of electrode potentials. The metal with the more positive (oxidation) potential, as given in Table 13-1 of the electromotive series, will pass into solution and displace a metal with a less positive potential.

Jan 1, 1970

By G. H. Khoe

Although some hydrometallurgical process liquors contain significant amounts of ferrous and arsenate ions, no reliable thermochemical data for the aqueous complexes and the solubility of the ferrous arsenate precipitate are available. The complexation of iron(11) with arsenate has been investigated using the potentiomemc titration method. The results indicated that virtually no complexation of iron(@ with arsenate has been observed. This is in contrast to the significant complexing reported for iron(1n) with arsenate. The solubility product of the precipitate was calculated using the concentrations of appropriate arsenate species pertaining to the observed precipitation pH&apos;s. The fit of the observed precipitation points on the solubility curve of the computed stability diagram was used to assess the appropriateness of the equilibrium model.

Jan 1, 1991

By Robert Lepsoe

IT is generally realized that in cyaniding the precipitation efficiency of zinc dust is due to the fine division or extended surface of its metallic particles; but frequently it is thought that the presence of other, metals, say 2-3 per cent. lead, is advantageous,. causing more complete precipitation. The results of testing about fifty brands of commercial zinc .dust have led to the conclusion that there is a distinct relation of precipitation efficiency to fineness and that the effect generally can be estimated by examining the size of metallic particles. The presence of lead was not found to be of any importance. SPECIFICATIONS Generally the term "97 percent. to pass a 350-mesh screen, 95-97 per cent. uncombined metallic zinc" is used by the leading European exporters. Among the many methods of determination of metallic zinc, I have found the iodine test (iodine in potassium iodide) very satisfactory and rapid. It has been controlled by the other methods, samples of the same product having been sent to three different analysts: Iodine method 98. 11 per cent. metallic zinc, Volumetric method 97.63 per cent. metallic zinc, Ledoux Co., New York Bichromate method 98.16 per cent. metallic zinc, Watson Gray, Liverpool, England Bichromate method 98.20 per cent. metallic zinc, Norway Inst. of Tech., Trondhjem

Jan 2, 1925

By Sigmund J. Andersen, Eva A. Mørtsell, Jostein Røyset, Randi Holmestad, Oddvin Reiso, Yanjun Li, Øyvind Paulsen, Calin D. Marioara

"With the purpose of increasing the extrudability of lean alloys, we reduce levels of the alloying elements Mg and Si in a 6xxx extrusion alloy. To avoid sacrificing strength, we investigate the compensating effect of smaller amounts of lithium and germanium, alone and in combination. Recent studies by atomically resolved high angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with density functional theory (DFT) calculations have demonstrated that while Li replaces Mg, Ge substitutes Si in the columns in the hardening ß’’-phase. Several studies have shown that Ge replaces Si in other precipitates as well, and that both Li and Ge promote precipitation and can improve macroscopic properties, like strength and thermal stability. The scope of the current work has been to investigate and document the combined effect of the two alloying elements. Of the investigated alloys, the one containing both elements displayed highest hardness, corresponding with a significant increase in precipitate number density. We used HAADF-STEM to determine the extent of Li and Ge in the precipitate structures.INTRODUCTION The two most important alloying agents, with respect to age hardening of the 6xxx alloy series, are Mg and Si. In general, 6xxx alloys are formed into their final shapes by rolling or extrusion, before being age-hardened at elevated temperatures around 180°C. The hardening effect during this stage is due to the formation of metastable, semi-coherent, precipitate needles along the three < 001>Al directions generally following the precipitation sequence (Marioara, Nordmark, Andersen, & Holmestad, 2006): Supersaturated solid solution ? atomic clusters ? Guinier-Preston-zones (pre-ß”) (Edwards, Stiller, Dunlop, & Couper, 1998) (Marioara, Andersen, Jansen, & Zandbergen, 2001) ? ß” (Andersen, et al., 1998) (Hasting, et al., 2009) ? ß’ (Vissers, Huis, Jansen, & H. W. Zandbergen, 2007), U1 (Andersen, Marioara, Vissers, Frøseth, & Zandbergen, 2007), U2 (Andersen, Marioara, Frøseth, Vissers, & Zandbergen, 2005), B’ (Vissers, Marioara, Andersen, & Holmestad, 2008) ? ß, Si (stable)"

Jan 1, 2018