Search Documents

By C. E. Coleman, D. Hardie, A. E. Wraith

A photoguaplric method of measuring crack velocities has been applied to an examilzation of- the effect of hydrogen on the impact properties of zirconium. Results indicate that the crack in hydrided zirconit travels at about 26 m per sec whereas that in the uacuum -annealed is dependent on the speed of the hammer. RECENT work on the effect of hydrogen on zirconium reveals that when hydrided zirconium is tested in slow bending the crack producing failure can be unstable. The mode of fracture seems to involve the crack linking up broken hydrides by a ductile mechanism in the zirconium matrix.2" In order to compare the fracture of zirconium with that of other metals which show unstable crack propagation, notably steel, the rate of the crack spread must be known. As the methods previously used for measuring crack growth are either unsuitable for the present work5-'' or very costly," a simple technique has been devised in which the maximum crack velocity is derived from a series of crack position-time measurements. EXPERIMENTAL PROCEDURE The experimental arrangement is shown schematically in Fig. 1. The flash unit12 was triggered when the Charpy hammer touched the specimen and the 6-psec flash of the lamp delayed by a preselected time interval in the range 100psec to 10 msec. The camera was left on open shutter during the test. From direct measurement on a calibrated photographic print, Fig. 2, the position of the crack and the specimen was found at a known time after impact and, from a series of such tests using an appropriate range of flash-delay times, the crack velocity was estimated. Preliminary experiments were carried out on mild steel above and below its transition temperature. Vacuum-annealed zirconium, and zirconium hydrided to 100 ppm H were then tested at 20" and 150°C. For comparison, Zr-2.6 pct Nb alloy (in the 0 + transformed /3 condition), vacuum-annealed or hydrided to 100 ppm H, was tested at 20 C. The chemical analyses of these materials are given in Table I. For the high-temperature tests a fine chromel-alumel thermocouple was spot-welded onto each specimen close to the notch. The test piece was heated up to 200°C to allow enough time for preparing the apparatus while the specimen cooled to the testing tem- perature. It was assumed that the specimen cooled uniformly. The accuracy of the flash-delay time was better than i2 pct i 5 psec. The crack length was taken as its maximum distance traveled normal to the length axis of the specimen. Errors in these measurements arise as a result of the uncertainty in the location of the crack tip and the difficulty in defining the exact position of the crack starting point. The latter was due to the bonding and large amounts of deformation at the hammer contact point, especially in the vacuum-annealed specimens tested at 150°C. The maximum error in the measurements was however estimated to be about 5 pct. DISCUSSION OF RESULTS From the trial experiments using mild steel above its transition temperature it can be seen from the plot of crack length against time after impact, Fig. 3. that a reasonable estimate of the maximum crack velocity at the surface of the specimen may be made. Other features of note are the initiation time before the crack is first seen and the slowing down period

Jan 1, 1967

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967

By A. C. Losekamp, J. B. Conway

Thermal-expansion data for, tungsten, rhenium, tantalum, .molybdenum, niobium, W-25 pct Re, Ta-10 pct W, ant1 Mo-50 pct Re are presented covering the range from room tempature to 2500°C. In these measureMents, made in a resistively heated tungsten tube furnace operating in a helium atmosphere, data for rod and sheet specimens were found to be identical; in addition, arc-cast and sintered tungsten were found to yield essentially identical results. Optical rneasurenlents of thermal expansion .made in any atmosphere other- than vacuum are subject to a refraction error which can be quite substantial. Specimens tested in helium appear shorter than when tested in racuum and hence a special correction factor must be applied to the helium data in order to obtain accurate results. WHILE it is true that linear thermal-expansion data for many of the refractory metals have been measured to very high temperatures, it is also true that except in a few instances the data from various investigators are not in good agreement. This is particularly evident in the case of tantalum and niobium although some tungsten data have been reported which differ by as much as 40 pct from the data of other investigators. Due to the sensitivity of both tantalum and niobium with respect to impurity absorption during exposure to high temperatures, it is probable that this single factor accounts for the majority of the discrepancies in the thermal-expansion data for these metals. However, this same factor can probably not be employed to explain the existing differences in the tungsten data. In all probability, these are due to errors in the measurement technique, to material composition variations, or to changes which take place in the material during the heating process (e.g., additional densifica-tion resulting from heating a sintered specimen above the original sintering temperature). In view of the discrepancies which exist in the linear expansion data reported for many of the refractory metals, the current study was initiated in an attempt to resolve such differences. Also, no high-temperature linear thermal-expansion data were found to be available for several refractory metals. Providing such data was another objective of the current investigation. MATERIALS In this study test specimens were employed in either rod or sheet form and in several instances both arc-cast and sintered material were employed. Material compositions are presented in Table I. Helium gas was fed to the furnace at a rate of about 0.5 SCFH and no special purification procedures were employed. However, the helium contained less than 50

Jan 1, 1967

By H. I. Aaronson, H. A. Domian, G. M. Pound

The thernodyna,nics of I the Proeutectoid ferrite re-action ha1.e been investigated on the bases of three diifevent descviptions of the statistical thernzodynamics of interstitzal solid solutions. Especially at low ternperatures, substantial dijeretzces are found in the valltes of the extrapolated y/y + a and cr/a + y equilibriurn curls, and in the To- co7nposilion metastable eqliilibriunz curl-es thus co,npited. Although neither actiztity nor phase-diagram date are able to distingrish udeqiutely among the various descviptions, the statustics of Lacher, Fouller, and Guggenheinz provide the ?nost conplete epresentation az3ailable of the single carbon-ctrbon interaction energy (w) nzodel of an intevstitiril solid solution, and the relationships deduced frojrl then2 are accordingly pre.ferred. The findings tlzut w in austenite 'aries significu?ztly uith tenpevntrue and that phase-diagawr data arc not accurately con?palible usith eqcrctions deduced on the basis of actility infoation indicate, hou'e13er, that a wzore cornplex nlodel of the uustenite , und pvobably of the .feyrite, solirl solutions will have to forn the basis of f4tuve statistical t1.eat1nents. Some suggestions for such a ruodel arc advanced. Althoug11 w represents a vepltlsio energy in austozite, it was found to corvcsporzd in ferrite to a binding energy, in qualitatit.e accord zc,itlz the internal-friclion results of Keefer and wert. ThE transformation of austenite to proeutectoid fer-rite is becoming recognized as an exceptionally useful vehicle for quantitative studies of the kinetics of phase transformations.'" Reasons for this popularity include well-characterized microstructures which develop on a convenient scale with acceptable kinetics within a considerable temperature-composition region, the absence of great sensitivity to common impurities, and, especially. the availability of a unique wealth of the ancillary information indispensable for the quantitative interpretation of kinetic measurements, including phase diagram,3 crystallographies diffusivity,5 inter-facial energy,=17 elastiit," specific vlume, ''' and ativity'-' data. Development of considerable amounts of additional thermodynamic information from activity data is of particular importance with respect to kinetic studies, since much of this information is needed in temperature-composition regions not directly accessible to presently available techniques for the measurement of equilibrium properties. A generally useful approach to the thermodynamics of solid solutions, which is of especial value in this situation, is based upon the formulation of the free energy of such solutions as a function of temperature and composition. The free energy of solid solutions has been resolved into many components. Particularly in the case of interstitial solutions, with which we shall be concerned in the present study, however, only the positional entropy component has been intensively studied. The other components are conventionally taken into account by fitting equations for the activity of the interstitial species or the temperature-composition path of phase boundaries, derived principally from positional entropy considerations, to experimental information on these quantities through adjustment of one or more constants in the equations. A number of studies of the thermodynamics of interstitial solid solutions have been made primarily on this basis,'"25 but only Kaufman, Radcliffe, and cohenZ2 (hereafter KRC) and ener''% ave applied the results of such studies to develop relationships for the thermodynamic quantities of interest in the austenite —- proeutectoid ferrite transformation. KRC made use of a model developed by cheil'' (on the basis of a previous study by ohansson'), and subsequently rede-rived correctly by Speiser and retnak,' in which a carbon atom is considered to inhibit occupancy of a certain number of its nearest-neighboring interstitial sites. schei120 determined the number of sites in austenite thus excluded by matching calculated and experimentally measured curves for the variation of carbon activity with the mole fraction of carbon. zener17 used a different approach. He assumed that the positional entropy of carbon is ideal both in austenite and in ferrite (i.e., no excluded interstitial sites), and included all other contributions of carbon in a temperature-independent "free-energy change" accompanying the transfer of 1 mole of carbon between the two phases. This quantity was determined by "pinning" an equation derived for the boundaries of the a + y region to experimental data on the compositions of these boundaries at a single temperature. In the present investigation, three different approaches to the thermodynamics of the proeutectoid ferrite reaction are examined comparatively: I) the method of Zener; 2) the model employed by KRC and predecessors; and 3) the more detailed statistical thermodynamic treatment of the same model developed by acher and Fowler and uenheim, ' in which the problem of overlapping regions of influence of individual interstitial atoms is resolved. In order to make these comparisons, it is necessary to undertake an extension of one aspect of Zener's method; since the Lacher- Fowler -Guggenheim (LFG) treatment has not been previously used in the present context, the necessary thermodynamic "superstructure" for this treatment will be developed in parallel

Jan 1, 1967

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By R. Fawley, M. A. Quader, R. A. Dodd

Stacking fault energies and annealing twin frequencies have been measured for austenitic stainless steels having a) constant 20 wt pct Cr and varying nickel contents, and b) constant 20 wt pct Ni and varying chromium contents. The effect of nitrogen has also been studied and, to a lesser extent, so has the effect of carbon. All measured stacking fault energies plot linearly against the corresponding annealing twin frequencies, suggesting that, for constant prior deformation and grain size, twinning frequency can be used to estimate stacking fault energy. Compositions low in nickel possess the lowest fault energy, while the maximum fault energy within the investigated composition range occurs mound 20 pct Cr-20 pct Ni. Nitrogen has practically no effect on stacking fault energy when increased from 0.005 to 0.05 wt pct, although Planar dislocation glide is associated with higher nitrogen contents; this may be a short-range order effect. Carbon may raise the stacking fault energy a little, and causes pronounced dislocation tangling in deformed alloys. The basically different dislocation structures promoted by nitrogen and carbon, respectively, are not associated with large variations in stacking fault energy, and the reason for the difference remains unknown. INTEREST in the dislocation configurations developed in plastically deformed alloys arises principally from a desire for an understanding of mechanisms of plastic deformation and fracture. Comparatively little basic work has been concerned with austenitic stainless steels, although considerable interest has developed in the fundamental aspects of deformation of these alloys since the suggestion that those compositions deforming essentially by planar glide are particularly prone to transgranular stress corrosion cracking.' Certain facts are well-established. An 18 Cr-8 Ni steel (type 304) has a low stacking fault energy which is increased by higher nickel contents, and the structure of these steels when moderately plastically deformed changes concomitantly from planar to less planar to distinctly tangled dislocation configurations. These changes are thought to relate to changes in stacking fault energy, and considerable effort has been expended in measuring stacking fault energies of austenitic stainless steels through the determination of node curvatures2"4 even though the method has limitations due to formula approximations,5 an upper limit of measurement of 50 erg cm-2 at the most,5 and the necessity of an extremely meticulous experimental technique. Therefore, it is not surprising that only qualitative agreement between different investigators is generally to be found.'-' At high energies where node radius measurements are inappropriate, some use has been made of annealing twin frequencies to estimate relative stacking fault energies, although a recent critical evaluation of the method suggests that it should be used cautionsly with due regard to effects of grain size and prior deformation.6 Finally, there is a question as to whether the structures of some deformed steels are due to ordering effects. In particular, the role of nitrogen in promoting planar dislocation motion has been suggested to be due to ordering,' but similar suggestions have been made for steels having low interstitial contents.4 EXPERIMENTAL Small ingots of austenitic stainless steels (-50 g) were prepared from components exceeding 99.99 pct purity, the nickel and chromium being Johnson Matthey "Specpure" metals. Carbon was added as pure graphite, and nitrogen as CrN. The components were accurately weighed, and it was assumed that the final composition was the same as the nominal composition

Jan 1, 1969

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969

By R. D. Stover, F. O. Shuck

The variation of binary-diffusion coefficients with composition in the liquid Bi-Sn system at 300°C was measured using the capillary-reservoir technique. The experimental coefficients did not exhibit a simple composition dependence. A number of tests were also made to determine the effect of variation of density with composition on convection within the capillaries. These tests indicate that the density changes arising from composition duferences may give rise to high diffusion coefficients unless care is taken to maintain a stable configuration. In recent years there has been considerable interest in diffusion in liquid metals. However, the bulk of the work done to date has involved measurements of self-diffusion or diffusion of dilute concentrations of "solute" metals. Because there are possible applications to liquid phase processing of metal alloys and since additional data may help to clarify the nature of diffusion in liquid metals, investigations of the concentration variation of diffusion coefficients in binary alloys have been undertaken. Of past studies only two have covered large ranges of binary composition. Niwa et al.' investigated the Pb-Sn, Bi-Pb, and Bi-Sn systems and Grace and Derge2 investigated the Bi-Pb system. Because of the discrepancy between the data of these investigators, it was deemed desirable to check the possibility of convection arising from the variation of density with composition. The capillary-reservoir technique of Anderson and saddington3 was chosen for the present investigation since it has been widely used for measurements involving dilute solute concentrations and it was the technique used by Grace and Derge.2 It was necessary, however, to modify the normal procedure of using a pure metal bath to avoid measurement of integral diffusion coefficients over large concentration ranges. The alloy system chosen for study was the Bi-Sn system for which there are some data available.' EXPERIMENTAL PROCEDURE In order to utilize the capillary-reservoir technique for measurements of diffusion coefficients as a function of composition, it was necessary to modify the normal procedure slightly. This modification consisted of using a reservoir composition which was only slightly different from that in the set of capillaries, in order that the integral coefficients measured might be taken over a small composition range and might thereby be assumed to approximate the differential coefficient at some average composition between that of the capillary and that of the bath. It was found that a composition difference of approximately 0.10 mass fraction provided a satisfactory compromise between a small increment in composition and reasonable accuracy in measuring changes of composition. The alloys were prepared from tin and bismuth of 99.999 pct purity. The materials were first cleaned of surface oxides, then weighed and melted to form a homogeneous alloy in a Pyrex filling apparatus. The capillaries used were of precision bore Pyrex tubing 1.000 *0.005 mm bore. Capillaries of various lengths (from 2.85 to 5.85 cm) were cut and sealed at one end by fusing a 3-mm Pyrex rod to the end. The capillaries were filled by inserting them into the filling chamber, evacuating the chamber, submerging the capillaries, and pressurizing the chamber with argon. Two sets of capillaries were prepared for each run. One set contained an alloy more dense than the bath alloy and one set a less dense alloy. This procedure was followed so that the effect of density difference on the measurement could be determined. After filling one set of capillaries, these were placed open end up in a capillary holder and transferred to the diffusion chamber which consisted of a Pyrex tube inserted into a graphite block. The second set of capillaries was then filled and placed into the diffusion chamber. The reservoir alloy, which had been melted in a separate crucible, then was poured carefully into the diffusion chamber. Sufficient reservoir alloy was used to cover all capillaries to a depth of several centimeters. All of these operations: capillary filling, melting of alloys, and diffusion anneal, were carried out in a fused-salt bath which maintained a temperature of 300"*1°C. All capillaries were permitted to diffuse for approximately 48 hr. At the end of the diffusion period the capillary holder was removed from the bath and

Jan 1, 1969

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.&apos; Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.&apos; Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.&apos; For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969

By M. A. Rigdon, R. E. Grace

The dissociation of cupric oxide to cuprous oxide and oxygen was studied with a microbalmce technique at 700" to 750°C. In this temperature range the dissociation pressure of the reaction 2CuO= Cu2O + 1/2 O2 was: The theory of near-equilibriwm reaction rates predicts a linear relationship between reaction rate and the Gibbs free-energy change for small values of AF/RT. This correlation is found to be valid for AF/RT = -0.1 or approximately 200 cal per mole away from equilibrium. THE theory of reaction rates near equilibrium as developed from classical thermodynamics suggests a small range of linear behavior between the overall reaction rate and the free-energy change accompanying the process. The extent of this linear correlation is generally unknown, even to the order of magnitude. The idea of linearity is also found in the formal mathematics of coupled transport phenomena, e.g., chemical diffusion, thermal diffusion, thermoelectricity, and so forth. The linear array of forces and fluxes which leads to various main and cross coefficients is predicated upon linearity between reaction rates and the bulk thermodynamics which govern the process. The general case in reaction kinetics is well-known: the magnitude of the free-energy change does not cor- relate with observed reaction kinetics, irrespective of whether the process occurs by diffusion or chemical reaction or both. The real need is to investigate specific reaction paths near equilibrium in order to learn of the limitations in attempting to correlate reaction rates and thermodynamics. It is the main purpose of this paper to examine the dissociation kinetics of cupric oxide under conditions of known driving force where the dissociation process is likely to occur by chemical reaction. A secondary objective is to obtain equilibrium data for the CuO-Cu20-O2 system. In a prior paper Edmiston and race&apos; investigated reduction kinetics of wustite in H2-H2O gas mixtures. The present study was carried out in oxygen according to the following reaction:

Jan 1, 1969

By J. Szekely, R. G. Carr

A method is presented which allows the extension of the Ergun equation for the description of gas flow through packed beds in a nonisothermal regime. The pressure profile in the packed bed is calculated by the establishment of a differential energy balance and the iterative integration of the integral equation thus obtained. The predicted values of the pressure distribution were found to be in excellent agreement with those measured experimentally, under carefully controlled conditions. MANY metallurgical processes are carried out in systems in which a gas stream and particular solids are contacted in a packed bed arrangement under strongly nonisothermal conditions. Ore sintering, the firing of pellets, the operation of regenerators, blast furnace technology may be quoted as examples. Although many aspects of these systems have been extensively studied, an important variable, the pressure distribution and the relationship between pressure head and flow rate, received only little attention to date. The purpose of the paper is to present a brief survey of relevant previous work, followed by a more rigorously formulated model, together with experimental results that afford ready comparison of theoretical prediction with measurement. PREVIOUS WORK A great deal of information is available in the chemical engineering literature on flow phenomena in porous media.&apos; The experimental results pertaining to gas flow were generally interpreted in terms of models based on the analogy with the flow through a pipe of an incompressible, isothermal fluid. Of the numerous, semiempirical correlations that have been proposed to relate pressure drop to the volumetric flow rate, the Ergun equation2 is generally regarded as the most satisfactory: The strong nonisothermality of the metallurgical systems previously mentioned would render the direct applicability of Eq. [I] rather doubtful as both density and viscosity are temperature-dependent. Ergun has used Eq. [I] for estimating the pressure drop in the stack region in the blast furnace by neglecting the viscous term and evaluating the gas density at the integral mean temperature.3 His calculations showed a rather variable agreement with measurements and it was uncertain whether the discrepancy found was attributable to the model or to the inaccuracies often inherent in measurements on an industrial scale. Other work on nonisothermal systems includes studies of the pressure distribution in sinter beds, notably by Voice et a1.4 and Mitchell.5 Mitchell developed a method involving the subdivision of the bed into several zones and assigning average property values (temperature, gas density, and so forth) to each zone. The pressure drop was then calculated for each zone by using an expression analogous to Eq. [I]. This method was an improvement over that described by Voice et al., but even here prediction and measurement differed by as much as 30 pct in certain cases. It would appear that no really satisfactory methods are available for the prediction of pressure drop in packed beds with a strongly nonisothermal regime. The method involving subdivision of the bed into small enough sections, that may be regarded as isothermal, would show promise; however its validity has to be tested by both a rigorous formulation and comparison with experimental data obtained under controlled conditions. In the following a formulation is presented together with experimental data allowing ready practical evaluation of the theory. FORMULATION The mechanical energy balance over an infinitesimal section of a packed bed may be written as follows:

Jan 1, 1969

By R. W. Gould, B. G. LeFevre, A. G. Guy

The resistivity anomaly known as the K state was studied in Ni-Mo alloys containing 10.5 and 14.0 at. pct Mo. Both these alloys exhibit a large K effect which depends on the mechanical and thermal treatment. On the basis of X-ray diffuse scattering studies which were correlated with resistivity measurements, it appears that the K state in dilute Ni-Mo alloys can be associated with changes in the degree of short-range order within the a phase. An interesting phenomenon that has received much attention in recent years is the K state. The K state is marked by anomalous changes in some of the physical properties of certain alloys without the occurrence of observable microscopic structural changes. One of the early pieces of work in this area was by Thomas&apos; who studied alloys of Ni-Cr, Ni-Cu, Ni-Cu-Zn, Fe-A1, Fe-Si, and Ni-A1. Upon annealing specimens which had been previously cold-worked or quenched from an elevated temperature he found an anomalous increase in resistivity over a certain temperature range. He also found that specimens which had been appropriately annealed to develop the K state showed a decrease in resistivity upon subsequent cold working. These effects are opposite to those found in normal alloys. Although the resistivity anomaly has been rather arbitrarily taken as the "definition" of the K state, there are several other interesting effects which accompany the resistivity increase. In Ni-Cr alloys,2, 3 for example, it was found that the hardness increases with increasing resistivity. It was also found that specimens which have been treated to develop the K state can be cold-worked for as much as an 80 pct reduction of area without an increase in the hardness. In Fe-A1 and Fe-Si alloys4 the K state is accompanied by an increase in flow stress and by a lattice contraction. In Ni-A1 alloys,5 specimens which have been treated to develop the K state also show an increase in elastic modulus. In Ag-Pd alloys6 the increased resistivity observed on annealing a cold-worked specimen is accompanied by an increase in the thermoelectric power and an increase in the Hall coefficient. The explanations of the K state phenomena are varied and depend upon the particular alloy in question. Several theories have been advanced to explain the increased conductivity with cold work on the basis of changes in the electronic configuration of the alloy as a result of local lattice distortions.7"9 Most investigators, however, believe that some type of local order in the solid solution, either short-range order (SRO) or clustering, is responsible for this effect. Theories concerning the relationship between ordering and the K state have for the most part been speculative, since there is little direct X-ray evidence that can be correlated with the above property changes. Much of the previous work on the K state was done in the Ni-Cr system where the small difference in the X-ray atomic scattering factors of the components nickel and chromium makes it very difficult to use X-ray diffuse-scattering measurements to determine the role of local order. In the Ni-A1 system, however, Starke et al.10 succeeded in detecting a connection between local order and the K state. It was found that a small but measurable K effect correlated with increasing SRO in the nickel-rich a phase. The manner in which local order might increase the resistivity of K state alloys is not completely clear. Since most of the known K state alloys contain at least one transition element, significance has frequently been attached to the presence of an unfilled d shell. It has been suggested that during the formation of the K state the number of conduction electrons decreases as a result of the transfer of s electrons to the d shell where they are more tightly bound.1&apos;11&apos;12 Koster and Rocholl13 have proposed that SRO can cause an increase in resistivity for alloy systems in which the number and mobility of charge carriers are reduced when the percent solute is increased. According to this hypothesis, the local environment of a given solvent atom changes in the same manner with increasing percent solute as it does with an increasing degree of SRO; hence the change in physical properties should tend in the same direction. In this hypothesis, SRO is considered only in a statistical sense, and the increased resistivity of the K state is attributed to a change in the mean distribution of electrons and holes in the s and d states as a result of SRO. From the work of Chen and Nicholson on Ag-Pd alloys,6 it appears that the K state can occur in systems for which the d shell is completely filled. These investigators explained the increased resistivity by picturing the SRO as small domains of some form of long-range order (LRO). According to ~ibson,&apos;~ the number of effective electrons can be reduced by the creation of a new Brillouin zone boundary near the Fermi surface of an alloy as a result of the changing crystallographic symmetry that accompanies the formation of a superlattice. This idea may be expressed in terms of the superzone concept.15 In the present work the role of local order in the formation of the K state in Ni-Mo alloys was investigated. The principal tools used in this study were X-ray diffuse scattering and electrical resistivity measurements; however, these data were supplemented by electron microscopic and field-ion microscopic data. The purpose of the work was to determine whether or not the K state in Ni-Mo alloys can indeed be attributed to the formation of SRO as has been proposed by previous investigators.

Jan 1, 1969

By Claude H. P. Lupis, John F. Elliott

The classic Siez~erts&apos; technique has been employed to determine the solubility of oxygen in liquid pure silver and the effect on the oxygen solubility of solute metal additions to liquid silver. The results indicate that oxygen deviates slightly from Sieverts&apos; law in pure silver as = 3.9. Gold, platinum, md palladium decrease the solubility of oxygen in silver. First-order free energy, enthalpy, md entropy interaction coefficients are determined from the data. An important aspect in the establishment of the formalisms to be applied to represent the thermody-namic behavior of components of solutions is the accuracy of the experimentally determined thermody-namic properties. Wagner developed the first-order free energy interaction coefficient.&apos; Recent papers2&apos;3 extend the treatment formally to other thermodynamic properties and define the second- and higher-order interaction coefficients. A current communication4 considers in some depth the requirements and limitations imposed because of experimental error on the use of several formalisms now under active consideration in the field. This communication reports the results of an experimental study of the behavior of oxygen in liquid silver alloys that was carried out concurrently with the development of Refs. 2 and 3 with the hope of providing sufficiently precise information so that enthalpy and entropy interaction coefficients could be determined. THE EXPERIMENTS The Sieverts technique was employed using an improved design of the reaction bulb over that developed originally by Humbert5 and subsequently improved by pehlke6 and Weinstein.7 The Vycor reaction bulb as shown in Fig. 1 was air-cooled and contained a port for the thermocouple angling off to one side and a vertical port for connections to the gas supply and

Jan 1, 1969

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969