Search Documents

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

TWO recent developments in open hearth steelmaking have had a substantial impact on metallurgical practices and operating procedures. These are: (1) the use of oxygen roof lances for accelerating the refining reactions, and (2) the use of a spring-arch, basic roof for prolonging the life of the furnace. Although these practices can be used separately, they are generally used to complement each other in an effort to obtain minimum heat time consistent with an acceptable rate of wear of the refractory roof, walls and port ends. DECARBONIZATION BY OXYGEN INJECTION The use of oxygen to speed carbon elimination was perceived by Sir Henry Bessmer but its practical use in steelmaking could not be realized until processes were developed for the manufacture of low cost, tonnage oxygen. However, as early as 1922 Bigge1 obtained a patent covering the use of gaseous oxygen to speed decarbonization of a molten steel bath. At that time, oxygen was available only in bottles and at a cost of $240 per net ton. At the end of World War II the price of oxygen had dropped to $80 per net ton, and as a result, metallurgical oxygen (99.5 per cent began to come into widespread experimental use for decarbonization in open hearth and electric furnace shops.2-8 Even this price prevented oxygen's routine use for other than decarbonizing the bath in shops producing substantial quantities of steels containing less than 0.40 per cent carbon. Today, tonnage metallurgical oxygen can be manufactured for less than $15 per net ton, and commercial purity oxygen (95 per cent is reported to cost less than $5 per ton. Thus, it is not at all surprising to find many open hearth shops effectively using large quantities of oxygen to accelerate decarbonization. Equipment for Oxygen Injection. The oxygen may be injected by a lance pipe inserted through the wicket hole and pushed several inches into the steel bath, or by a water-cooled jet inserted through the back- wall, endwall, or roof, and immersed in the slag or set just a few inches above the slag. Oxygen at approximately 100 psi is piped directly to control stations adjacent to each furnace. The installations should include adequate safety devices such as fire checks and emergency valves,

Jan 1, 1964

By M P. Simpson

Forty one whole rock samples from the Gold Cross low-sulfidation epithermal Au-Ag deposit have d18O values that range from 4.4 to 9.3 per mil, with an average value of 7.0 per mil. Unaltered and weakly altered rocks have d18O values greater than eight per mil, and the orebody is surrounded by samples that are depleted in 18O. A strongly silicified sample adjacent to the Empire Vein System has a d18O value of 9.0 per mil, similar to previously reported analyses of vein quartz (7.0 to 11.7ë, average 9.4ë). This suggests that, in detail, Golden Cross may have a zone of 18O-enriched wall rocks in the core of the deposit, adjacent to the main underground veins. Although some workers have suggested that stable isotope geochemistry may provide useful information for epithermal mineral deposit exploration, at Golden Cross this is not the case. Alteration minerals, major elements and trace elements all define larger, less ambiguous halos than the zone of 18O-depleted wall rocks.

Jan 1, 2001

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By G. G. Roy, R Shekhar

Pachuca tanks are extensively used for the cyanide leaching of gold and the carbonate leaching of uranium, processes in which oxygen mass transfer plays a very important role. Experiments were carried out to clarify the effect of design and operating parameters on oxygen mass transfer. Parameters such as the ratio of tank height to tank diameter, the ratio of draught-tube diameter to tank diameter and the tank design were found not to influence oxygen mass transfer. Results also showed that equal superficial gas velocities may be used as a criterion for scaling up oxygen mass transfer in both full-centre-column and free-air-lift Pachuca tanks with clear water. A volume-averaged, volumetric gas-liquid mass-transfer coefficient (k'av) was used to characterise oxygen mass transfer in full-centre-column tanks. The axial dispersion model was used to determine k'av. The resulting model used only tank geometry and air flow rate as inputs for the prediction of k'av in industrial-scale tanks. Predictions from the model show clearly that "local" mass-transfer coefficients, measured at one or two locations, may not adequately represent gas-liquid mass transfer in industrial tanks. It is therefore necessary to obtain an estimate of k'av

Jun 18, 1905

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By Cloutier JY, Quinn P, LeClerc A, Dube G, Agar GE

Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer. The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared with a readily available but under utilised method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate.

Jan 1, 1993

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation' of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

According to our experimental results, the following oxygen probe recommended, that is, the magnesia stabilized zirconia was employed as a solid electrolyte and Fe.FexO solid elect- rode was used as a reference electrode. Using such an oxygen probe, we tried to measure the oxygen potentials in molten metals, mattes and gases in the following fields of non-ferrous metal industry, molten copper in the side launder before casting, molten crude lead in the forehearth of ISP blast furnace, molten copper mattes in the forehearth of blast furnace and in the settler of flash smelting furnace, gas in the settler of copper flash smelting furnace and flue gas in the electric furnace for ferro-silicon. In the past ten years or so, many experi- mental results in the field of fundamental studies have confirmed that the equilibrium oxygen potential could be measured conveniently and accurately by an electrochemical method using a zirconia solid electrolyte. Recently, such an electrochemical technique has been also applied to a device for physicochemical invest- igation or process control in the non-ferrous metal industry. Such a device consists of an oxygen con- centration cell with stabilized zirconia, and it is commonly called an "oxygen probe" or "oxygen sensor".

Jan 1, 1980

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989

By H. Y. Sohn, H. K. Lin

The leaching of primary porphyry chalcopyrite ore under simulated solution-mining conditions was studied using a packed-bed reactor. A mathematical model incorporating the intrinsic leaching kinetics of chalcopyrite and pyrite grains, the pore diffusion of dissolved oxygen within the ore fragments, liquid-solid mass transfer, and the effect of fluid flow and axial dispersion was formulated and tested for the overall leaching process. The dependence of oxygen solubility on ionic strength of the solution was also incorporated into the model. Satisfactory agreement between model pre- dictions and experimental data was obtained. The model can also predict the rate of the leaching process under different temperatures, oxygen pressures, solution flow rates, and different size distributions of ores.

Jan 1, 1991

By Ono K, Oishi T

Electrochemical determination of the oxy- gen partial pressure in the Fe-0-SiO 2 ternary systems saturated with solid silica was done by measuring the activity of oxygen in a silver bath in equilibrium with the molten slags using zirconia solid electrolyte galvanic cells. From the data obtained, the activity ~Faii.st composition relations were calculated

Jan 1, 1980

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By L. A. Taylor, R. O. Colson, D. S. McKay

The production of oxygen on the Moon utilizing indigenous materials will be essential for successful lunar colonization. Several processes have been put forth to accomplish Lunar Liquid Oxygen (LLOX) generation. The schemes that have received the most study to date involve: 1) Reduction of ilmenite (FeTi03) by H2, CO, CH4, CO-Cl2 and Cl2, plasma. 2) Molten silicate electrolysis, both unadulterated and fluoride fluxed. 3) Several others, including H, reduction of glass, carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reduction of ilmenite and molten silicate electrolysis processes have received the most study to date. They are both feasible schemes and have various pros and cons, including their feedstock requirements. However, all processes should be addressed at the onset of LLOX research. This paper reviews several of the most studied and feasible processes for winning oxygen front lunar materials. There is an obvious need for more experimentation and study.

Jan 1, 1994

By L. A. Taylor

The production of oxygen on the Moon utilizing indigenous materials is paramount to a successful lunar colonization. And several processes have been put forth to accomplish this. The LLOX generation schemes which have received the most study to date are those involving?: 1) the reduction of ilmenite (FeTi03) by H2, C, CO, CH4, CO-CI2, & Cl2 plasma, 2) magma electrolysis, both unadulterated and fluoride-fluxed, and 3) several others, including carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reductions of ilmenite and magma electrolysis processes have received the most study to date. They are both feasible schemes with various pros and cons, including their feedstock requirements. However, all processes should be addressed at least at the onset of our considerations. There is an obvious need for considerably more experimentation and study. Some of these requisite studies are in progress, and this paper reviews several of the most studied and feasible processes for winning oxygen from lunar materials.

Jan 1, 1991