Search Documents

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By L. A. Melis, J. W. Rowson

"Cluff Mining has successfully operated a gold recovery plant at its Cluff Lake operation in northern Saskatchewan to recover gold f rom Phase 1 uranium leach tailings. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-inpulp, gold recov ery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and operating data and metallurgical results from the operation are provided.INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 per cent by Cameco and 80 per cent by Amok Ltd. /Ltée. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake, 700 km north of Saskatoon, capable of processing 300 000 tonnes o f ore to produce about 4 000 000 lb UPs (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""0"" uranium orebody from 1980 to 1983. The leach tailings from the Phase I mill operation were found to contain elevated level s of gold . These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the""0"" orebody .During the Phase I operation some 6475 tonnes of leach tails were produced and stored in a total o f 2916 large concrete containers (vaults). This method of storage was, at the time, deemed to be the preferred method of temporary storage for the tailings.This temporary storage of high-grade gold tailings facilitated the reclamation and reprocessing of the leach tail s for gold recovery. The primary reason for reprocessing the Phase 1 leach tails was to provide for long-term permanent disposal of the material as an admixture with Phase II tailings in the Cluff Lake tailings disposal area. Although there was limited tonnage, the high gold content in the material made the in stallation of a gold recovery circuit economically justifiable."

Jan 1, 1989

By L. A. Melis, J. W. Rowson

"Cluff Mining operates the Phase II uranium mine and mill at Cluff Lake, northern Saskatchewan. During the Phase I operation, uranium tailings were generated by acid leaching of a gravity concentrate and high-grade ore for uranium recovery. The pre-treatment gravity process, as well as the high-grade nature of the ore, led to a concentration of gold in the tailings which justified the installation of a small circuit to recover the contained gold. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-in-pulp, gold recovery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and typical operating parameters are provided. 1.0 INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 percent by Saskatchewan Mining Development Corporation (SMDC) and 80 percent by Amok Ltd./Ltee. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake 700 km north of Saskatoon, capable of processing 300,000 tonnes of ore to produce about 4,000,000 lbs. U308 (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""D"" uranium orebody from 1980 to 1983. The leach tailings from the operation Phase I mill operation were found to contain elevated levels of gold. These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the ""D"" orebody."

Jan 1, 1988

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By M. Vondersaar, B. Bulnes

Quemetco, Inc.,. as a subsidiary of RSR Corporation, operates one of RSR's three secondary lead smelters in the City of Industry, California, next to a residential area within Los Angeles County. The Reverberatory furnace serves as the main reactor for melting lead grid and paste recovered by the battery crushing system. Feed material is introduced via screw conveyor after drying in an upstream rotary kiln. Slag produced by the Reverb flows directly to an electric arc furnace. Products from this one-pass furnace system consist of soft lead bullion from the reverb, hard lead bullion from the arc furnace, and a non-hazardous slag from the arc furnace. Furnace bullion is processed into finished product in a six-kettle refinery. An overview ·of plant operations is presented. Where applicable, references will be made to changes that have taken place during the last decade.

Jan 1, 2000

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By Firth B. A

The classification performance of a Dutch State Mines (DSM) Rapped Sieve Bend has been investigated in a series of experiments. Coal slurries of a nominal 0.5 mm size were classified in the separation range of 0.10 to 0.14 mm at pulp densities from 6 to 21 per cent by mass of solids, and flow rates of 110 to 1375 litre min-1.The results obtained showed that the partition curve and water split io oversize was dependent on the solids flow rather than slurry flow rate or pulp density. For most of the operating conditions considered an accurate classification of the fine coal was obtained. The undersize efficiency was susceptible to solids flow rate, and was less than 70 per cent for solids flow rates greater than 16.7 tonne hour-1 metre-1 width of screen.

Jan 1, 1983

By W. R. Phibbs

THE blast furnace of the Columbia Steel Corpn., at Ironton; Utah, was put in blast April 30, 1924, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PER CENT. Moisture 3.90 Volatile 39.00 Fixed carbon 51.10 Ash.... 6.00 Sulfur : 1.07 The analysis of the coke is: PER CENT. Volatile 0.55 Fixed carbon :...:.::: :..:.:: 89.70 Ash 9.75 Sulfur 1.05

Jan 1, 1928

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation's entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944

By K Lownie, R Sani, A Sianturi

Part of the PT Freeport Indonesia (PTFI) mine production is in the process of transitioning from the deep ore zone (DOZ) mine to the deep mill level zone (DMLZ) mine. The DMLZ mine is the next lift in the caving series and lies 500 m below the current DOZ footprint.In order to reduce the need for a very expensive additional ventilation system for the DMLZ mine, it was decided to reconfigure some infrastructure and upgrade the performance of the three existing DOZ mixed flow ventilation fans in situ, reducing the new fans required to two. This was far less costly than providing complete new installations.These fans are installed in individual underground chambers in DOZ mine exhaust drifts and connected to the DMLZ mine exhaust drifts system in 7 m × 7 m airways size, through sets of 6 m diameter by 500 m high raises.The upgrade process involved replacement of motors, fan shafts and bearings. The existing 1600 kW DOZ mixed flow fans are 3500 mm diameter and operate at a speed of 595 rev/min and were originally designed to deliver 390 m3/s at 3.3 kPa. Efficiency optimisation may be required at a later date.The upgraded DMLZ fans are required to deliver 425 m3/s at 3.7 kPa and it was necessary to increase in motor size and speed to 2200 kW at 710 rev/min. This paper will discuss the fan upgrade project and in particular the integration of an unusual ventilation system, which is based on the semi parallel operation of multiple large fans.CITATION:Sani, R, Sianturi, A and Lownie, K, 2017. Operation of deep mill level zone mixed flow fans after the first fan upgrade – a parallel fans case study, in Proceedings Australian Mine Vent Conference 2017, pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Fred W. Stiefel

THIS paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct.[t] This part of the tunnel is r5 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 19 to 19 ft. in diameter, It lies at a depth of 400 ft. below sea level, with a maximum overburden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotive each of 13 gross tons and having a [inum] speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 950,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using con¬crete presented a problem of hauling a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 cu. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles, Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. CHOICE OF LOCOMOTIVES In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. PROPOSITION No. I The go-hp. storage-battery locomotives available (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1942

By Fred W. Stiefel

THIS paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct.[t] This part of the tunnel is 15 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 17 to 19 ft. in diameter. It lies at a depth of 400 ft. below sea level, with a maximum over-burden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotives, each of 13 gross tons and having a maximum speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 750,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using concrete presented a problem of hauling a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 cu. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles. Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. CHOICE OF LOCOMOTIVES In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. PROPOSITION No. I The 90-hp. storage-battery locomotives available (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1942

By J. H. Jacobs

This report records a chapter in the history of the development of an electrolytic manganese industry in the United States. Nearly all the manganese requirements of the United States have been imported. Although there are large quantities of manganese ore in the United States, most of it is low-grade and cannot be used for the production of ferromanganese. Since the electrolytic production of manganese carried out by a process developed in the laboratories of the Bureau of Mines offers a method whereby the extensive low-grade deposits may be utilized and since commercial development had proceeded slowly, the Bureau constructed a new and larger pilot plant at Boulder City, Nev., where abundant electric power was available. An authorization in November 1940 covered a plant of only several hundred pounds daily capacity. Additions to some sections author¬ized by subsequent appropriations have enabled the plant to produce over 2,000 pounds a day for extended periods.

Jan 1, 1946

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By G. E. Norman, A. L. Mckague

"The new smelting process commenced operation in 1978. The pelletizing and sinter plants were replaced with slurry-fed roasters and the blast furnaces with electric furnaces. The existing converter aisle and matte handling facilities remained unchanged.Process DescriptionNickel-copper concentrate is partially roasted in two slurry-fed fluid bed roasters. After gas cleaning, the sulphur dioxide gas is transferred to the acid plant. The roaster product is conveyed to two electric furnaces for smelting to produce a waste slag and furnace matte. The slag goes to the disposal area and furnace matte containing the metal values is processed in the converters for further removal of iron and sulphur.The final matte containing about 75 per cent metal values is shipped to the refinery in Norway.The commercial smelter was designed for 2135 tonnes per day of concentrate, with an availability of 85% . Roasters and electric furnaces were sized at 117 per cent of design, or 1250 tonnes per day on each of two lines. Concentrate storage capacity in the plant is sufficient for two to three days' plant operation.The new smelting process will be discussed under the following headings:Concentrate Slurry HandlingFeed PreparationRoaster OperationRoaster Gas CleaningCalcine TransferElectric Furnace Operation and Process Control Converting and Matte HandlingUnder these headings, process control , equipment changes, and plant performance after three years' operation is reviewed. A brief discussion of accident prevention , and working environment is also included ."

Jan 1, 1984

By D Pepper

Despite the limited literature regarding the pressure filtration of mine tailings (compared to the large number of papers published each year on paste thickening of tailings) the number of mines dry stacking filtered tailings is approximately equal to the number of mines storing tailings in paste form. Main drivers for filtering tailings are: water recovery, future rehabilitation costs for tailings storage area and permitting requirements. In arid climates, the cost and scarcity of water justify the capital and operating costs associated with pressure filters. Further justification for filtered tailings is the potential for progressive reclamation of the dry stack, which can proceed earlier and faster than the reclamation of a tailings dam.Filtered tailings must be transported to the storage area by trucks or conveyors. For dry stacking, 70 - 80 per cent solids content (by mass) is typically acceptable, however the primary goal is to provide a filter cake that is consolidated and dry enough to prevent bridging and build-up on the materials handling equipment. It has been observed that high average solids contents (~70 per cent) can be achieved while the centre of the filter cakes is still wet and sticky, presenting challenges for the transportation of the solids. Appropriate controls must be in place to ensure consistently easy to handle solids are discharged from the filter.FLSmidth has installed two fine coal tailings dewatering systems in the United States. One of these systems incorporates a Deep Cone Thickener« upstream of the filter press to minimise the amount of water that must be filtered, while the other tailings filter press is fed by a high rate thickener. The operation and performance of these filters is discussed and compared to the lab testing used to size the full-scale equipment.CITATION:Pepper, D, 2012. Operation of filter presses for tailings dewatering, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 241-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012