Search Documents

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By H. Reginald Hardy

This report is Volume II of a three volume final report dealing with the microseismic monitoring of a longwall coal mine. The research presented in Volume II is concerned with the evaluation of field techniques for obtaining seismic velocity data required for computing microseismic source locations. The report describes the evaluation of a number of different field techniques and the seismic velocity data obtained at the Greenwich mine site where the micro-seismic studies, described in Volume I of the final report, were carried out. Three different methods were employed to evaluate seismic velocities, namely; surface refraction, down-hole, and transmission. In all cases the seismic sources were either located on surface (mechanical impact) or near-surface (explosive charges). It was found that a mechanical energy source could be conveniently utilized to determine shallow velocities and make bedrock-regolith interface depth determinations. For deeper velocity determinations suitable explosive charge sources Here required. In general, refraction data did not always plot in a linear manner and some subjective interpretation was necessary. The down-hole method was found to be useful for incremental vertical velocity evaluation, however, the transmission method provided the most consistent average vertical velocity data. At the Greenwich site seismic velocities were found to be anisotropic with values ranging from 9,551 to 10,739 feet per second depending on direction.

Jan 1, 1977

By H. Reginald Hardy

This report is Volume III of a three volume final report dealing in general with the microseismic monitoring of a longwall coal mine. The research presented in Volume III was undertaken as part of the overall microseismic project in an effort to relate, if possible, observed micro seismic activity with surface subsidence. A discussion in regard to the correlation of these factors is presented in Volume I of the final report. Field measurements of subsidence carried out at a Central Pennsylvania Coal Mine are described. Comparative analysis of actual field results with data obtained using empirical and finite element techniques Has undertaken. Comparison of field results with published National Coal Board data revealed marked differences. The influence of stronger rock beds overlying the coal seam in the current study was assumed to I be the main cause. Use of the general Gaussian profile resulted in a satisfactory fit to the field data provided the value of the maximum field subsidence was used in the analysis. In general, when low tensile strengths were assumed for the associated rocks, finite element techniques gave results which compared well with the observed field data. The study also indicated that at shallow depths there is a marked difference in subsidence over dip and rise sides of the coal-face, maximum subsidence being shifted more towards the dip side. Finally, time-dependent deformations were shown to be insignificant shortly after mining operations ceased.

Jan 1, 1977

By James C. Fowler

The design and field testing of a seismic miner detection and location system arc described. This work was carried out over a period of three years. The first two and one-half years were sponsored by Continental Oil Company, while the last period of tests were done as the first part of a one-year contract with the U.S. Bureau of Mines. Laboratory and field experimentation in three different nines under simulated emergency conditions have led to three important results: (1) Taps on roof bolts with normally available objects can usually be detected up to horizontal distances of 1,000 ft. (2) The origin of the tans can be located by on-site processing with a small computer. (3) Some predetermination of the approximate location is necessary for a quick and successful rescue. This report also includes preliminary specifications an,d cost guidelines for construction of a transportable field system capable of matching the performance characteristics of the one used during the field tests.

Jan 1, 1973

By David E. Kaslow

In sampling dust laden air by drawing the medium into an inlet, some larger particles fail to follow the air and a true sample is not obtained. Inertia prevents particles from accelerating with the air as well as from turning sharp bends; also the particles' weight causes them to fall relative to the air. An analytic solution to the sampling efficiency calculation by Levin gives particle paths and sampling efficiencies for various particle sizes when the inlet can be treated as a point sink. However, the flow field in the neighborhood of an aspirating tube is quite different from a point sink flow. Employing Levin's solution in the outer field, trajectories in actual flow fields have been calculated by computer to locate the critical trajectories separating the entering particles I paths from those paths where the particles hit the tube wall or escape. Sampling efficiencies are presented in terms of 3 variables--a dimensionless particle size coefficient, a dimensionless orifice size coefficient and the tube orientation--for the no-wind case. Over most of the range of sampling conditions, the Stokes drag law can be used and dependence on the variable--particle Reynolds number--can be ignored. A procedure for achieving maximum efficiency in design of a sampler is proposed. Whether these results apply when typical room-sized eddies constitute the ?calm air? environment is not known.

Jan 1, 1974

This report covers the work performed by the Advanced Products Division of FMC Corporation under Bureau of Hines Contract J0155166, Design Evaluation for Development of an Advanced Bolter Module. FMC has evaluated the existing ISMS bolter designs, and the corrections and improvements in progress, including the effect of the three-chain magazine presently being fabricated, and recommends that a complete bolter module featuring a new magazine, safety post and lower stabilizer or similar device be designed, fabricated, and tested, A 29 week program is proposed which includes a four week demonstration. This module would eliminate those reliability problems not presently being solved and would provide a reliable bolter module for a production oriented miner/ bolter.

Jan 1, 1975

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By David J. Hoadley

This report describes the development and limited testing of a semi-automatic, raise climber, Compact Service Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 1,000-lb payload capacity, control from the traveling cage and from up to three remote stations, operating in vertical or inclined raises 3 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an umbilical 'cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The hoist has been demonstrated successfully in an above ground test tower. This report provides a detailed description of the hoist design and its demonstrated performance to date.

Jan 1, 1985

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By John M. Dale

Sulfur is a plentiful, low cost, unique material whose physical properties can be altered and employed in structural applications. This program was undertaken to develop an optimum sulfur based formulation for use as a coating to both seal and support mine walls. The initial effort in the program was devoted to a laboratory study of the physical and mechanical properties of a variety of sulfur base coatings that were specifically formulated for this application. Concurrent with formulation development, laboratory equipment and techniques were developed for spray applying the sulfur based coatings to the ceiling and walls of a structure that simulated the interior of a mine. Much of the formulation work was guided by the experiences encountered when attempting to spray the formulations overhead. One hundred parts of sulfur modified with 10 parts of talc, 3 parts of milled glass fiber, and 2 parts of dicyclopentadiene was found to be a fire retarded, low odor, low eye irritation, sprayable formulation for sealing and strengthening mini, walls. An invention disclosure on this formulation was submitted to the Bureau of Mines and a patent application was filed. Various mineral samples were obtained and adhesive strengths of the formulation to these samples in both the wet and dry state were measured. With the development of an attractive sulfur based coating material, attention was directed to the design, fabrication, and testing of a portable spray application unit so that coatings might be applied in the field to various rock surfaces and earth formations for further evaluation. The unit was fabricated in the Southwest Research Institute shop. Once operational, the unit's capabilities were field tested and demonstrated at three separate locations. Upon completion of the field testing, the unit was shipped to the Spokane Mining Research Center where Bureau personnel were instructed in the use of the unit.

Jan 1, 1972

By G. E. Bobeck

The first year's work of a proposed three-year study of the effects of the exposure of coal mine roof rocks to the mine atmosphere has been completed. The project has been terminated. The goal of the project was to determine if possible the mechanism or mechanisms by which coal mine roof rocks interact with the mine atmosphere and weaken, and coupled with mechanical stresses, ultimately fail. The scope of the study was limited to the effects of environmental factors on the deterioration of the rocks. While mechanical stresses may play an important role in the interaction of environmental factors, stress effects were excluded from the study. In order to study the effects of environment on coal mine roof rocks, samples were obtained from several coal mines in the western states. The rocks forming the roofs of most of the mines visited were shales of varying composition. These shales were subjected to numerous tests to determine how the rocks changed with time after exposure. In addition, the identity of the minerals present in the shales was determined by x-ray diffraction analysis and by thermal analysis as well as by optical microscopy

Jan 1, 1973

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974