Search Documents

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By William J. Halvorsen

We are currently doing work on three ways to improve the performance of our froth flotation systems. One development is the use of a cationic flocculent added to the feed of the froth cells. This does give some improvement in ash of the product particularly in a situation where there is a good bit of clay present. Difficulty is usually experienced with clay carrying over with the water contained in the froth product and also adhering to the coal surfaces. Addition of the flocculent to the flotation feed preferentially flocculates the clay causing it to drop into the tails. The results of some laboratory test work on Pittsburgh 88 Seam coal in Eastern Ohio is shown in Table 1. [ ]

Jan 1, 1979

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By T. D. MacQueen

Thank you Mr. Stevens. It's a pleasure for me to be speaking to this meeting of the Society of Mining Engineers of AIME this afternoon, and the Gypsum, Association is grateful for the invitation. A brief word about who we are: the Gypsum Association is the trade association for the gypsum industry - the manufacturers of gypsum board and lath a-d plaster. We have a membership of eight companies. These eight companies produce about 90% of the gypsum products manufactured in the United States ... closer to 94% actually. Our headquarters is in Evanston, Illinois. We have an east coast office in Washington, D.C. where the eastern manager handles technical and building code matters and maintains liaison between all of the government agencies and departments and our industry. We also have a west coast office in Los Angeles where our west coast representatives is heavily involved with the Uniform Building Code and ICBO. And then in the Evanston office our manager of technical and building code services, Herb Carlsen, bites his nails and loses his hair over these problems and various other projects that come in, such as conversion to metric and various other things. We also have a research associate at the National Bureau of Standards in Washington who is currently concentrating his efforts on the combustibility of building materials. His studies involve current testing methods, definitions, data analysis, and proposed new testing methods,.' It is anticipated that this program will lead to a better understanding of non-combustibility of building materials and systems. I mentioned that our members represent over 90% of gypsum products,' manufactured in the United States; it might be well to point out a couple of statistics about what that really means. According to the Bureau of Mines,

Jan 1, 1977

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Haase W. C

The content of this paper will identify recent developments in walking dragline technology including utilisation of planetary swing dnves, high voltage generators, unique bucket configurations and increased machine capacity resulting from changes to front-end geometry. The benefits to mine operators for increased performance, reduced cost, improved availabilities, simplified maintenance, and ease of operation will be identified and discussed. The feasibility and application of the technology as a retrofit on existing equipment will also be covered in the presentation. All the technology being presented has been recently commissioned into operating Australian mining operations and will be presented from a practical, as well as theoretical perspective.When the Marion 8000-Series Dragline was introduced in the early-1970s, it quickly became the industry standard for high productivity and availability. Features like outboard bearing propel, four-chord deep section boom and the over/under fairlead have proven their superiority in thousands of hours of round-the-clock operations in a variety of tough digging conditions worldwide. Marion has currently sold 31 of these 8000-Series Draglines into the Australian mining community.

Jan 1, 1992

By Robert Archer

Two new alloys of the "strong alloy" class having improved fabricating qualities are described; also methods of producing alloys of the duralumin type with greater strength and hardness than previously obtained, are given. IT is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, including duralumin, are fundamentally wrought alloys. Castings of the same compositions, heat-treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has; in general, undergone a reduction in section of at least 80 per cent. by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 2, 1925

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By Alain A. Sonntag

This paper presents the most recent developments in KREBS technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1989

By A. A. Sonntag, I. Szanto, D. A. Goodman

This paper presents the most recent developments in mixer-settler technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1993

By Manuel Diaz del Rio

At the present time there are over 5,000 Kms of railway tunnels in existence throughout the world. In many cases these tunnels were built over a century ago using techniques obsolete today. Supervision and maintenance of these tunnels is essential to the economy of each country involved. For this purpose an electro-optical measuring system has been designed incorporating highly complex soft and hardware (15 mW laser, high resolution TV camera and processing computer), mounted on a vehicle. Its job is to scan, record and compare sectional gauge values (profiles) and strains inside tunnels both momentarily in situ and on permanent record, as an aid to the supervision work. From the state of the strains observed, in conjunction with an infrared spectrum of the tunnel lining and soil involved, the mechanical stresses in the tunnel can be deduced by applying the boundary elements method.

Jan 1, 1981

By Colwell JB, Cronan DS

Manganese nodules cover great areas of deep ocean floor far from land, and have long been considered a major potential resource of nickel, copper, cobalt and perhaps manganese. A decade ago there was a period of intense evaluation of nodule fields, especially those lying between the Clarion and Clipperton Fracture Zones in international waters southeast of Hawaii. There, nodules are abundant and of high grade (average of 2.4% Ni+Cu+Co). The evaluation activity has since declined, but a recent agreement on lease boundaries among all interested parties may lead to a resurgence of work. Indeed, French and Japanese groups have pushed ahead with field and economic assessments.The Southwest Pacific, where there are large nodule fields in the waters of the Cook Islands and Kiribati, has seen considerable assessment of resources in the last ten years, especially through a major field programme of the Japanese Metal Mining Agency. The best prospect appears to be in the South Penrhyn Basin, in Cook Islands waters, where nodules are very abundant but of only moderate grade (1% Ni+Cu+Co). Using a cut-off of 5 kg of wet nodules per m2, Cronan (1989) and Cronan et al. (1989) have estimated the total resource to be a huge 110 million tonnes of Ni+Cu+Co.

Jan 1, 1990

By D. Hodouin

The improvement of mineral processing data using material balance computer programs is nowadays a current practice in many plants, engineering companies or research centers. It now becomes more obvious that such programs should integrate new features such as the preprocessing of data, the estimation of less accessible process variables and an in-depth interpretation of: the computed results. A few solutions to these new problems are already available. The feasibility of a mass balance computation for instance can be examined by analyzing the degree of redundancy of the measurements prior to any data adjustment. New variables such as chemical analyses in particle size intervals or liquid phase composition can be included in a set of measurements. Finally, a sensitivity analysis can be used to analyze the reliability of the results, to detect eventual outliers or to redesign a sampling scheme. Some illustrations of these new developments are presented.

Jan 1, 1989

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By Ralph A. MacMillan

Electronic systems introduced for haulage equipment in recent years probably exceed what mine management is prepared to use. Haulpak trucks alone are equipped with General Electric's Statex III drive system controls, Detroit Diesel's DDEC, Cummins' Centry engine management system and the Haulpak Management System (HMS). The future holds promising developments of even more sophisticated electronics that will lead to unmanned truck operation and control. Trolley-assist will finally come into its own due to the importance of environmental issues, as well as the high potential for increased productivity with dramatically lowerfuel consumption. All of these high technology systems do not mean much unless they add value to mining operations. Some of the benefits that can be expected from these systems are reviewed. In the near future, haul truck control and monitoring systems will be fully linked by telemetry to a mine's dispatch system, as well as to its maintenance management information system. The manufacturer and distributor can also be kept in the communications loop, so that they can better serve customer needs. Portable computers will allow technicians to talk to machine systems to quickly locate a problem, look up service information, check what parts are required and electronically order them.

Jan 1, 1994

By Boris J. Kochanowsky

In a mobile crushing unit system trucks are replaced by a conveyor, which results in a continuous, almost fully automated operation with all its attendant advantages. Because of new designs for large mobile crushing units that have been placed on the market, the use of these plants has increased significantly during the last three years. Gains in productivity and reductions in costs are vital to every mine operator, and the shovel-crusher-conveyor system is a powerful tool with which to achieve this goal. New Designs Increase Throughput While Reducing Size The basic concept of the shovel-crusher-conveyor scheme of operations is simple and sound, with the result that domestic operators are showing a growing interest in its application. A number of operators have been using small mobile crushing plants for several years, but large operators, in spite of considerable interest, have not been able to use this system because no mobile crusher capable of crushing 1000-2000 tph of rock loaded by a large shovel (6-12 cu yd) has been available. A suitable crusher must accept rock of the size handled by these large shovels, be simple in design, easily maneuverable, remotely controllable, and have price and maintenance costs not much higher than those for stationary crusher installations.

Jan 9, 1968