Search Documents

By C. R. Jenkins, G. S. Taylor

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets, and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event and drained the pond, creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were measured on samples of influent and effluent to evaluate pond performance. Particle size analyses were conducted on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement.

Jan 1, 1987

By Charles R. Jenkins

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event, and drained the pond creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were run on samples of influent and effluent to evaluate pond performance. Particle size analyses were run on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement. Through the entire surface mining process un- protected soil is exposed to direct rainfall and subject to accelerated erosion. Without controls, receiving streams would be "choked" by the additional sediment load. Several states, including West Virginia, require that sediment control ponds be constructed to trap the sediment before the water enters receiving streams. Even well designed ponds have exhibited difficulty in meeting effluent limitations. In a study supported by EPA, about half the ponds did not meet effluent limitations (1). There is a critical need to reduce sediment losses using presediment pond controls or by improving sediment pond performance. The objectives of this study were to evaluate modifications designed to improve sediment pond performance by; 1) monitoring three ponds prior to modification, 2) install floating baffles and 3) modify the principle spillway and determine the change in pond performance.

Jan 1, 1985

By C. van Loggerenbergt, P. E. Ventert

A strong incentive exists for the coal-preparation engineer to improve plant efficiency by modifying circuits and upgrading process equipment, since these result in lower production costs and more valuable plant products. At the Grootegeluk Coal Mine, it was found that the overall plant efficiency could be improved by modifications to the dense-medium circuits, the installation of additional process equipment for the recovery of fine coal, and improvement of the fine-material processing circuit. Apart from these modifications, there is still potential to increase the plant efficiency, particularly in the utilization of plant waste, the recovery of slimes, and even the improvement of cycloning performance as a result of new cyclone design. This paper points to the potential wealth locked up in existing coal-preparation plants, and shows how the coal-preparation engineer, with new technology at his disposal, can unlock this wealth.

Jan 1, 1992

By L. J. Lindsay

Kaiser Resources Ltd. operates a coal mining complex in Southeastern British Columbia. A large surface mine, a conventional underground mine, and an innovative hydraulic underground mine are presently in operation. The products of these mines are fed to the Elkview plant. This coal has to be prepared to 9. 5% ash and 6'o total moisture for export from the port of Roberts Bank near Vancouver, British Columbia to Japan at a rate of 4. 5 Mltpy. The moisture requirement for the coal product was recently increased to 8. 0% total moisture. The entire operation has been described in various publications (1), (2), (3). Details of the venture will not be repeated in this paper. In this paper we hope to describe the modifications made to the original coal preparation plant in order to satisfy market requirements for quality and quantity of coal.

Jan 1, 1974

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By S. L. Bell

Most Australian longwall coal mines are currently working coal faces up to nine kilometres from the surface. In the event of a mine emergency walking this sort of distance wearing breathing apparatus becomes very difficult if not impossible. Self-rescue continues to remain the focus of mines rescue in Australian coal mines and this paper describes a vehicle modification which will improve the chances of a miner rescuing himself. Existing mine personnel transport vehicles are not designed to operate in some types of atmospheres that may be present following a mine fire or explosion event. An Australian Coal Association Research program (ACARP) funded research project recently completed in Australia has developed a specification for a vehicle that is able to operate safely in some types of post emergency atmospheres. During the course of this investigation, diesel and electric vehicles were examined prior to making a final decision on vehicle suitability. Based on the fact that there are already some 1500 diesel vehicles in use in underground coal mines in Australia it was decided that modifications to existing diesel engines would be the best option. This presentation will outline the proposed specification for the vehicle and the reasons behind the decisions that were made with respect to the specification.

Jan 1, 2003

By Fabiano Della Libera da Silva

Este artigo modifica a heurística de sequenciamento ATCS (Apparent Tardiness Cost with Setups) com vistas à sua aplicação na retomada de pilhas de minério (entendidas como tarefas a serem sequenciadas) em pátios de recuperação. Para tanto, inclui-se na formulação critérios relevantes para as operações de pátios de estocagem, como tempo disponível para o empilhamento de um produto, demanda relativa, tempo de recuperação da pilha e data de entrega, tempo de deslocamento das recuperadoras entre pilhas (setup) e índice de qualidade. O método proposto foi aplicado em um sistema de recuperação de minério composto por dois pátios, duas máquinas recuperadoras e doze pilhas. A sequência de recuperação gerada pela heurística proposta foi considerada coerente por especialistas de uma empresa mineradora.

Aug 16, 2017

By João Batista Ferreira Neto

A escória de aciaria pode ser uma alternativa como mistura para o cimento portland, substituindo parcialmente a escória de alto-forno. Um processo pirometalúrgico tem sido desenvolvido para promover a modificação química da escória de aciaria LD. Os experimentos foram realizados através da refusão de 300 kg de escória de aciaria LD, seguido de sua modificação no estado líquido. Essas escórias foram resfriadas com o uso de esferas metálicas. Análises de fluorescência de raios–X (FRX) e microscopia eletrônica de varredura (MEV) das escórias revelaram uma relação entre composição química, condição de resfriamento e a formação de fases cristalina ou vítrea. As amostras de cimento foram obtidas através da mistura de 25% de escória modificada e 75% de cimento Portland, resultando em mais de 280 J/g de calor de hidratação acumulado em 72h, expansão abaixo de 0,1% em ensaio em autoclave e resistências à compressão acima de 42 MPa com 28 dias. O processo mostra potencial para ser aplicado no tratamento de escória de aciaria LD.

Aug 17, 2017

By Bruno Gomes Silva

Durante os reparos gerais nos conversores LD da CSN, as atividades de refratamento como demolição a quente, troca das ventaneiras, montagem do canal de vazamento e montagem do revestimento de trabalho e permanente, fazem parte do caminho critico do cronograma e são diretamente responsáveis pela dinâmica do evento. A montagem do canal de vazamento demandava uma série de atividades que exigiam maior tempo para execução e suporte para atividades em espaço confinado. Este trabalho apresenta sinergia entre fornecedores e diversas áreas envolvidas na montagem do canal de vazamento, onde a metodologia empregada resultou em redução no tempo de execução da atividade, disponibilidade da mão de obra e segurança operacional.

Jul 30, 2018

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By G. A. Dawe, E. G. Kelly

Because of the nature of the breakage in the Barmac vertical spindle impactor, the 80% reduction ratio is very small, so that when an energy efficiency is calculated from Bond's method, it appears to be very low. However, the product size distribution contains a high proportion of fines. It is argued that the production of these fines accounts for the high energy consumption, and Bond's method is modified to account for this, by considering the crusher to be, effectively, a number of smaller crushers in parallel, each having a different reduction ratio.

Jan 1, 1990

By Eduardo Lozano, Vilem Petr

This paper provides an overview of a new method for avalanche control using a high explosive charge placed at the avalanche runout zone: the case charge technique. This new avalanche control technique is well-suited to mountain roads presenting several advantages over the existing methods: minimum deployment time, low cost, reduced probability of misfires, and decreased operation time in the avalanche danger zone. The research work presented in this paper was conducted via large scale laboratory experiments where the detonation velocity and the blast physical properties were measured. During the charge design, several parameters were controlled: charge mass, diameter, geometry, density, and external confinement. In addition, the effective range of case charges was increased by the use of the Mach reflection for certain topographical situations. Finally, field test results collected by the Colorado Department of Transportation (CDOT) during the 2017 winter season are presented. The CDOT avalanche control crews have adopted the new case charge as the preferred technique in numerous avalanche locations along the Rocky Mountains roads.

Jan 1, 2018

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By M Chaudhari, G Manekar, D Shome

MOIL Limited is operating 7 underground and 3 opencast mines in central India and producing annually more than 1.2 million tonnes of various grades of manganese ore. The underground mines are operating at shallow - 90 m at Munsar mine to moderate - 353 m at Balaghat mine below the surface with horizontal cut and fill (HCF) or its variant method of stoping with post filling by hydraulic sand stowing. The Munsar mine is being worked underground since 1903. The opencast mining is presently stopped. The ore body below the opencast quarry is geological continuity of the area excavated in past by opencast method of mining. The underground mining is done through the adit in three levels i.e. 270’L, 220’L, 170’L and by incline in western part of the property at 70’L. The horizontal drift development has been developed in the manganese ore body with sill drive of 5 m above the sill pillar in lower level at 70’L and barrier pillar of 5 m thickness is left for protection of upper level at 170’L. Valuable mineral has been locked in sill pillar and therefore rock mechanics investigations have been carried out. On the basis of study now the drift development has been carried out in footwall rock at 70’L, (-) 30’L and below levels and it has improved the mineable manganese ore by about 20%. In this modified HCF stope design, an alternative fill material in place of sand, which has been developed in house by use of overburden (OB) material after treatment, has been used for hydraulic stowing. The experimental trials find out that the alternative fill material of OB is more compact and forming a non expansion floor for the men and machines in the stope. This will certainly help in the introduction of mobile underground mining equipment for drilling in the stopes and mechanical mucking, transportation and loading of the ROM. The paper presents rock mechanics investigations and future use of alternative fill material of OB for better safety and productivity at Munsar Mine of MOIL. CITATION:Manekar, G, Shome, D and Chaudhari, M, 2018. Modified ground support with alternative fill material for ground control at Munsar underground manganese mine of MOIL Limited, India, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 58–65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982