Search Documents

By H. A. Coy

THE Mascot mines of the American Zinc Co. of Tennessee are situated in the Holston River valley, in Knox County, Tennessee, about 13 miles (20.9 km.) east of the city of Knoxville, and form a property of three operating shafts and one open pit. A second open pit is located at Jefferson City about 16 miles (25.8 km.) east of the Mascot mines. Geology Topography.-The principal topographical features of the region within which the zinc deposits occur is a series of parallel northeast and. southwest ridges which reach altitudes of 200 to 400 ft. (61 to 122 m.) above the valley. These ridges are formed of resistant formation such as sandstone, quartzites, etc., while the valleys are occupied principally by limestone, including Knox dolomite, and by shale and other formations subject to quick erosion. The Holston River valley is wide and open with a rolling surface. Sink holes are common to the limestone portion, the general aspect of the valley being that of well-rounded hills with low intervening valleys superimposed upon which is a characteristic sink-hole topography. General Geology.-According to Keith, the rock formation of the area extends from the lower Cambrian into the Silurian. The region has undergone severe deformation with heavy faulting, the underlying Cambrian having been brought to the surface by a series of low angle thrust faults, the strike of the faults and formations paralleling the general northeast and southwest direction of the topography and clipping at varying angles to the southeast. In general the Cambrian quartzites, sandstone, etc., occupy the ridges while the Cambro-Silurian dolomites, limestone and shales occur principally in the valleys. Of the latter, the Knox dolomite is of particular interest to this paper in that it is the ore carrier in the Mascot area. The ore is associated with more or less irregular breccia zones, the degree of brecciation varying from-a fine crushing to a breaking that involves blocks of large size. The breccia zones

Jan 9, 1917

By P. B. Scotland

THE mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry has displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The smelting of these ores in blast furnaces continued until about 1893, when the rapid exhaustion of the high-grade ore led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. ORE OCCURRENCE The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry. Low-grade oxide ore formed the outcrop of some-' the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 2, 1915

By Charles Bell

THE Telluride mining district of southwestern Colorado is defined by the 37° 45' and 38° parallels of latitude and 107° 45' and 108° meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: Gold $58,274,527; silver 41,830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 lb., valued at $8,324,910; zinc 18,141,182 lb. valued at $1,323,787; or a total production of $101,473,408. All: claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for, milling and domestic purposes and the latter for milling, power, and domestic purposes.

Jan 2, 1924

By Charles Mitke

THE United Verde Extension mine is located in the Jerome mining district, on the eastern slope of the Black Hills, approximately northeast of the town 'of Jerome, Yavapai County, Arizona. The ore deposit may be termed a replacement in Yavapai schist. This schist is one of the oldest formations in the district, being probably of volcanic origin, and has been folded and faulted and contains intrusions of diorite and quartz porphyry. It is believed that the mineralization followed the porphyry intrusions and replaced the country rock; this was followed by erosion and a period of secondary enrichment, all completed in pre-Cambrian time. Later sediments of sandstones and limestones, to the depth of approximately 600 ft. (182 m.), were laid down, followed by volcanic flows. Faulting and erosion again took place, resulting in the present complicated arrangement of the strata. Prospecting, therefore, is very difficult, because the sediments practically cover the mineralized areas. This necessitates the sinking of deep shafts, cross-cutting, and, in some instances, diamond drilling to learn something of the various relations of the different formations and the occurrences of intrusions associated with ore deposition. The locating of new orebodies, therefore, is beset with innumerable difficulties. EARLY MINING METHODS The two orebodies constituting the principal resources of the company are known as the- small orebody and the Bonanza, or large orebody. These are about 150 ft. (45 m.) apart, and while they appear to be distinct orebodies may later prove to be connected. The character of the ore, the general associations of the porphyries adjoining the orebodies, and other characteristics, both in the ore-and general environment, are very similar. The small orebody was the first to be discovered and was mined for some time before the Bonanza was found.

Jan 1, 1919

By Arthur Smith

THE Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district-the United Verde and the United Verde Extension-lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., . a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to? the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Wood chute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the . smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the vicinity of Allen Springs, at the south end of Mingus mountain and all within the boundaries of the Prescott national forest reserve.

Jan 3, 1924

THE morning session on mining methods with R. M. Raymond as chairman was devoted mainly to papers on explosives and the discussion of these papers. A paper on the numerical index of the re-sistance which rocks offer to the penetration of a drill bit was also read. The first paper, "Relation Between the Oxygen Bal-ance and Propulsive Strength of Eight Gelatin Dynamites" by G. St. J. Perrott, N. A. Tolch and J. E. Crawshaw, was presented by Mr. Perrott, super-intendent of the Pittsburgh Experiment Station of the U. S. Bureau of Mines. In this paper which is the beginning of a series of publications on explosives, Mr. Perrott stated that the attempt was made to put down in quantitative form the facts which have been known to explosive engineers for a long time. Eight samples of 40 per cent gelatin dynamite, with oxygen content varying from + 15 to - 36 per cent of the theoretical amount necessary to form complete combustion with all of the combustible elements were tested. The experimental work showed that a bal-anced explosive did not give the greatest propulsive strength-but the most favorable range was from - 8 to - 25 per cent oxygen. The experimental work also brought out the fact that the wrapper of a stick of dynamite enters quite completely into the explosive reaction, and gelatin dynamites from which the wrapper had been removed developed less strength than the a same explosive with the wrapper. The second paper, "Effect of Oxygen Balance of Gelatin Dynamites on the Gaseous Products of Det-onation," by G. W. James and G. St. J. Perrott, was also presented :by Mr. Perrott. The first portion of this paper is given over to a discussion of the relative merits of different types of apparatus for testing and analyzing the combustion products of dynamites. Three types were used (1) the Bichel gage, (2) the Crawshaw-Jones apparatus and (3) the Hercules tank. All three of these types were used in testing dynamites whose oxygen balance varied from-35 to + 6 per cent.

Jan 3, 1928

By AIME AIME

THE initial meeting on Mining Methods* opened at 10 o'clock Monday morning with Scott Turner as chairman and W. Spencer Hutchinson as vice- chairman; about 60 attending. After preliminary announcements Theodore Marvin was called on for his paper,, entitled "Rock Tunnel Methods," which has been appearing serially in The Explosives Engineer. Marvin read the introduction and called attention to the account of one or' two particularly' interesting projects, such as the. Brooklyn water supply tunnel. E. D. 'Gardner, Char1e.s S. Hurter, L. D. Lamont and Spencer P. Howell took part in the discussion, Howell commenting on the fact that, in one case cited, misfires had occurred through detonator wires 'coming in contact with the case of an unapproved flashlight, .,: and that all flashlights should be approved.

Jan 1, 1931

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By E. P. Pfleider

THE history of fundamental research in mining is not one of which the profession can be particularly proud. It has been one of the slowest industries in applying the fundamental sciences to the solution of many of its more difficult problems. True, many of the processes are not adaptable to laboratory techniques, and much of the work must, of necessity, be done in the field. It is for this reason that the mining executive seldom has been conscious of the value of research on a laboratory scale on problems pertaining strictly to mining. Most of them, however, fostered much testing in the allied fields of ore dressing and metallurgy.

Jan 7, 1951

Development: Iron Ore In Peru Utah Construction Co., of San Francisco and a Peruvian Government corporation have signed an agreement for development of a large iron orebody in Peru. Most tests show 60 pct iron or better. Most of the ore is magnetite. Although ore will be shipped mainly to Eastern U. S. blast furnaces, shipments to the West Coast may develop as the orebody opens up. The construction firm indicated three American steel companies have shown interest in the project. The orebody is located 300 miles south of Lima and about 15 miles from the coast at the same longitude as New York City. Allen D. Christensen, executive vice-president of Utah Construction noted that the distance is shorter between Peru and the East Coast. The ore deposit measures about four to five miles in one direction and 10 miles in the other. As many as 15 outcroppings within these limits have been reported. Several of the outcroppings are thousands of feet long by several hundred feet wide, Christensen said. Shipments between 100,000 and 200,000 tons of ore per month are projected by the company. Cost of opening the mine to production may go over $5 million, Christensen said. It would include building of docks for ocean going vessels, housing, and heavy duty mining and processing equipment. The contract with the Peruvian government gives Utah Construction six to eight months for additional tests and a 20 year concession for mining the orebody. Peru will collect royalties on all ore. The company will also supply about 300,000 tons per year for an electric furnace to be installed by the Peruvian Government at Chimbote. No steel is produced in Peru now. Utah Construction formed the Argonaut Mining Co. last year, and was shipping iron ore from British Columbia to Japan at a rate of more than 50,000 tons a month, before winter weather decreased operations.

Jan 1, 1952

US Tin Mission To Study Costs in Far East A move to obtain adequate supplies of tin at prices the United States is willing to pay was initiated when the interagency tin mission left for the Far East. The Mission, which includes representatives of the Reconstruction Finance Corporation, State Department, Defense Minerals Procurement Agency and the Bureau of Mines will go to Indonesia and Malaya. The primary purpose of the mission, according to officials, will be to study tin production costs, not to negotiate for the purchase of tin. The mission will be prepared to enter into negotiations, if the Far Eastern producers are amenable. The United States withdrew as a large-scale buyer of tin some months ago in protest against what it considered exorbitant prices being charged in the Singapore market. Subsequent attempts to negotiate for a steady tin supply at what this country considers reasonable prices have been unavailing. The U. S. is prepared to enter into a two or three year contract with the price of tin somewhere between $1.00 to $1.12 per lb. The decision to abstain from the market has not yet put a squeeze on U. S. supplies. Substantial quantities of tin still are coming in from Malaya under an old contract.

Jan 12, 1951

•Mineral Development Corp. of Salt Lake City, Utah purchased the Somerset and Oliver coal mines from the Kaiser Steel Corp. The mines are located at Somerset, Colo., about 75 miles east of Grand Junction, Colo. Somerset Town, with housing for 600 persons was included in the transaction. The mines employ 115 miners and have a combined capacity of 1750 tons per day. The Minerals Development Corp. is headed by Claude P. Heiner and is controlled by Godfrey L. Cabot, Inc. of New York and Boston. The Cabot Company is a major producer of carbon black. • The Dept. of Interior has announced that the name of the Defense Minerals Administration will be changed to Defense Minerals Exploration Administration. The new name of this defense agency more nearly describes its duties, since the mineral programming, procurement and claimant functions of the former DMA have been transferred to the Defense Minerals Procurement Agency. C. O. Mittendorf, formerly acting administrator of DMA, is serving as acting administrator of the new DMEA.

Jan 1, 1952

New Device Eliminates Blasting in Coal A non-explosive device developed by duPont utilizes the high pressure of a gas generated inside a steel tube which is inserted in a hole drilled in a coal seam to break down the face of coal. Chemical reaction is started by an electric current which produces heat to initiate the action. The same heat destroys the starter wire as soon as electric current is no longer needed. The tube containing the chemical is closed at the outer end by a plug with electrical connections, and at the other with a disk that is ruptured by the compressed gases formed. When the gas has been liberated in sufficient quantities to create a desired pressure the disk breaks and the released gas breaks down the coal face. The new device is called a Chemechol.

Jan 10, 1951

• Phelps-Dodge Corp. signed an agreement with the Defense Materials Procurement Agency to increase copper production from the east ore deposit of the company's Copper Queen branch at Bisbee, Ariz. The company agreed to undertake a $25 million expansion program, including construction of a concentrating and leaching plant at the Bisbee mine and enlargement of the Douglas smelter. The Government agreed to buy the first 112,500 tons of the first 150,000 tons produced at 22e per lb if the company could not sell at a higher price. The new facilities will have a yearly capacity of 38,000 tons and should be in production by late 1954 or early 1955. • American Smelting & Refining Co. has started construction of a new building to house the Central Research laboratory at South Plainfield, N. J. It will have approximately 75 individual laboratories and an equal number of offices and shops. Modern apparatus to be installed will include electron microscopes, electric and fuelfired furnaces, miniature copper refineries and zinc plants, wire drawing machinery, and large pilot plant laboratory. In the new building scientists study the base metals, and the development of new uses for a number of Asarco by-products, arsenic, and little

Jan 11, 1951

By H. S. McQueen

THE central Ozark region of Missouri has inter-ested geologists and mining engineers for many years. Of particular interest are the mineralized sink-hole type deposits, some of which have produced large quantities of iron ore. Deposits of coal are also known in this part of the State, and in mode of occur-rence are similar to the iron ore deposits. Occurring in the same general area, and often associated with coal, are deposits of high-grade non-plastic flint fire clay, and high alumina or diaspore clay. At present these clays are the most important materials being mined from the sink-hole type deposits. Deposits of high-grade flint fire clay have been known to occur in this region for many years, the Kelley pit near Rolla, Phelps County, being discovered in drilling for iron ore shortly after the close of the Civil War. Mining operations had disclosed at an early date masses of rough, open-textured "sandy" clay associated with the flint fire clay. Some of the hard flint clay also con-tained rounded shot-like particles of "sand." Both types of clay were considered of inferior grade and unsuited to the manufacture of fire brick. These clays were discarded in mining as value-less, in some instances being used for road metal. Some knowledge of the high alumina content of this sandy material had been obtained by 1908 1, and by 1917 the high alumina content was gen- erally known, and commercial shipments of what is now called diaspore clay were being made. These deposits of diaspore clay associated with flint fire clay form the only known deposits of commercial importance in North America. The production of diaspore and flint fire clay at present exceeds that of any former year. Statistics covering the production and value of the former were not collected prior to 1922, and the figures given below do not cover the tonnage of clay mined by companies and used in their own plants, so that the total produc-tion probably is much larger than that indicated. The figures were collected by the U. S. Geological Survey and the U. S. Bureau of Mines in cooperation with the Missouri Bureau of Geology and Mines.

Jan 6, 1928

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997