Search Documents

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By J J. Cilliers, E Ventura-Medina

Mineral froth flotation is used to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. As air is blown into the slurry, the hydrophobic particles attach to the air bubbles, while the waste particles remain in suspension. While the froth rises up, bubbles start to coalesce and burst, allowing the entrained liquid surrounding the bubbles to drain and return part of the gangue to the pulp. Mineral separation is therefore a function of the amount of valuable material loaded on the bubble shells, as well as the amount of gangue material entrained in the liquid channels separating the bubbles (Plateau borders). As a result, the separation performance of the process is affected by mineral attachment and drainage or bursting in the froth. This study aims to establish the relationship between solids loading, froth stability and separation performance. For this purpose, a series of industrial experiments were carried out to measure mineral attachment as well as bubble bursting by combining direct sampling of the bubble films and video image analysis of the froth surface. This work suggests that the solids loading on bubbles strongly affects the separation performance. The results generally showed that solids loading and concentrate grade are closely related, while froth bursting rate can be linked to the drainage of gangue from the Plateau borders and also to the overall recovery of valuable mineral. It was shown in particular that higher loadings, usually associated with higher froth bursting rates, are indicative of more selectivity in attachment and therefore a higher mineral grade in the concentrate. Additionally, this work suggests that bubble solids loading and froth stability are essential parameters to include in froth flotation models as they allow control and optimisation of the flotation performance.

Jan 1, 2005

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.'*' Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory' except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.' It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------'8'77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.'*' Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory' except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.' It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------'8'77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, &apos;which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By J. W. Snavely

A practical mathematical treatment is presented for the determination and control of conveyor belt acceleration, particularly for conditions of starting where vertical curves are involved. A typical sample problem is analyzed, with required calculations, to clarify the procedure. THE part that acceleration plays in starting a belt conveyor and its effect on belt conveyor design are well understood in a general way. Its practical importance is easily overlooked, however, and under some conditions, it is absolutely necessary to give the problem of acceleration detailed study. Most handbooks on conveyor belting design adequately present basic data for the determination of acceleration values. This paper will only attempt to present practical thinking and a convenient method of treatment of acceleration in belt conveyor design. Mathematical Analysis In working out the various problems of conveyor belt acceleration, the starting point, as presented by the handbooks, is the familiar formula of "force of acceleration is equal to the mass times acceleration." By expressing these fundamental quantities in terms of belt conveyor design, it is possible to arrive at the unsuspected conclusion that the acceleration time for horizontal belt conveyors is independent of the load, and instead, dependent upon the belt speed, the type of drive arrangement and drive pulley, and the idler coefficient of friction. The mathematics leading to this conclusion are shown in Table I, which has been prepared to show this derivation. While at first the conclusion just given may not seem to be reasonable, further reflection indicates that obviously the type of drive pulley and the type of drive do affect materially the tension in the conveyor belt, and thus, as clearly shown, the time of acceleration is dependent upon the factors mentioned. Inasmuch as all of the factors except time are predetermined by the belt conveyor design, it becomes relatively easy to establish the accelerating time and to reduce further this time determination to a simple graph from which the time in seconds can be read directly. Such a graph is given in Fig. 1. The table appearing on Fig. 1 should be explained further. For a given belt speed, the time of acceleration can be expressed as a percentage of the belt speed. The time of acceleration is also dependent on the drive arrangement, and changes in the drive arrangement consequently change the time of acceleration. It further follows that for a given belt speed, the time expressed as a percentage of that belt speed also changes with the type of drive. Obviously then, it becomes possible to graph the percentage of speed for .each type of drive against the belt speed and accelerating time, after which, for a given belt speed and type of drive, the time can be read directly in seconds. Two constants were established for Fig. 1, the first one being the limiting of the maximum acceleration tension to 35 pct of the full load operating tension in the belt. The purpose of this is to limit the total tension imposed upon the belt during the acceleration period to 135 pct of the full load operating tension, &apos;which is the amount required to start or breakaway the fully loaded belt conveyor from rest. The other constant is the friction factor used for the idler equipment, which has been established as 0.022. For installations where it is necessary to establish the values of acceleration, invariably high grade idler equipment is used, and it has been established from field experience that 0.022 for the idler friction factor is amply conservative. The use of this friction factor for idlers must be tempered with judgment, of course, for occasions will arise where more power than indicated is required to start, even with the very best of equipment, such as low temperature operations that tend to congeal the grease in the bearings and thus produce additional friction drag. An inspection of the table in Fig. 1 affords a convenient rule of thumb method for determining the acceleration time, which conveniently can be 5 pct of the belt speed in seconds. The 5 pct of belt speed figure is close to the average for most types of drives. In using Fig. 1 it must be emphasized that it applies accurately to horizontal belt conveyors only.

Jan 1, 1953

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther&apos;s remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By G. G. Gunther, C. L. Boeke

DISCUSSION I. M. Symonds, (Cia. Minera de Penoles, Monterrey, N. L., Mexico)—Messrs. Boeke and Gunther have written most interesting papers describing their zinc de-leading operations. Mr. Gunther was kind enough to show me his operation last fall. Aside from the excellent results, I was most impressed by the ease of control. I had expected a difficult operation requiring careful control and supervision, but found one requiring little attention. The only disappointing fact of the separation is the poor copper recovery in the concentrate of the delead-ing float. The final zinc concentrate still has about 3 pct chalcopyrite, assuming the copper is chalcopyrite, and adversely affects the zinc grade. If the copper mineral is free, the poor recovery is probably due to the high cyanide concentration. Fortunately, about 75 pct of the copper is recovered before the pulp goes to the zinc circuit. Mr. Gunther&apos;s remarks about proper cyanide to zinc sulphate ratios cannot be overemphasized. Although our experience has been confined mostly to the conventional lead-zinc separation, we have found these ratios most important, and more important in the mill than in the laboratory. The laboratory appears to give optimum results over a wider range of reagent control than the mill, especially in regard to the effect of cyanide. In handling relatively high grade ores in the mill we usually find that ratios of cyanide to zinc sulphate of 1 to 10 or 20 or higher work best. Where there is a substantial amount of chalcopyrite present it has been noted that cyanide in the range of 0.02 to 0.10 lb per ton of ore is often beneficial in zinc rejection and possibly in copper recovery in the lead concentrate, while larger amounts, say 0.20 to 0.25 lb per ton, will float more zinc and cause a serious rejection of chalcopyrite. On an ore with 15 to 20 pct zinc content we have had to use 0.8 to 1.2 pounds of zinc sulphate per ton of ore with the above cyanide to obtain optimum results. Some time ago we made a laboratory study following Parral and Santa Barbara practice on an ore which had never a very satisfactory rejection of zinc in the lead concentrate. The results were not encouraging and a mill test was not run. Since then the study has been reopened using in the laboratory fresh zinc concentrate from the mill instead of one made in the laboratory. A reasonably clean lead float from the zinc concentrate was obtained. It has been checked several times and each time the zinc concentrate made in the mill responds and the one made in the labora-

Jan 1, 1953

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author&apos;s reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond&apos;s statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author&apos;s reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond&apos;s statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By C. L. Sollenberger, Will Mitchell, Ford F. Miskell

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953