Search Documents

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Ronne Hendrajaya

"The influence of microstructural defects on strength in Si3N4 is reviewed. The presence of cracks, pores and inclusions greatly affects the strength of Si3N4. The micron order crack size and distribution were quantified by micrographic technique. The observed defect size was range from 4 µm to 28 µm.The density of defect increases as the defect size decreases. The correlation between defects size and density was better represented on the logarithmic graph. The correlation was linier. IntroductionFracture in ceramics materials occurs from. In order to understand the relationship between strength and defects, it is necessary to examine the fracture process quantitatively.1In this study, the micrographic technique is used to determine the defects size and distribution in Si3N4. The observed data will be used to predict the material strength by using fracture mechanics rnodel.2Experimental ProcedureThe sintered Si3N4 specimens ( SNl, Japan Fine Ceramics Center) were sliced into 1mm thick . The both sides of specimen surface were polished into by using diamond slurries with particle size down to 2µm. The final thickness was 0.045 mm. The optical microscope (NIKON OPTIPHOT02-POL) was used to observed the internal defects with transmission mode. The reflection mode was used to determine the surface defects, so that the internal defect could be distinguished from surface defect. The measurement and counting was taken on the micrograph and the longest part of the defect was measured as the defect size. The size density distribution of internal defect is taken."

Jan 1, 2000

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Alisson Paulo de Oliveira, Altair Lucio de Souza, Jacson Morais Borges, Cleiton Arlindo Martins

A customized version of the Microsim-PM software for one Steckel rolling mill was built and adapted for specific mill parameters. The focus of this study is to use this model, which predicts the austenite grain size distribution evolution during rolling, to understand and quantify metallurgical issues happening during hot rolling. This will allow the steel mill to optimize the rolling process and chemical composition before the first industrial trial. Materials rolled for final thicknesses of 4.75, 6.30 and 12.5 mm of a carbon manganese steel and a microalloyed steel were selected to tailor the equations used by the model and to accurately reproduce the reality of the Steckel mill. This paper analyses the results from the customized model and compares them to mill data and final microstructure. Measured and predicted Mean Flow Stress (MFS) values are compared. After rolling, the material is subjected to accelerated cooling using laminar cooling. These cooling curves obtained from mill data are also considered to analyze the final microstructure characterized for all the cases using EBSD. The quantification of the microstructure allows for a better understanding of the relationship between chemical composition, process parameters and mechanical properties.

Oct 1, 2019

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By Henry Rawdon

ONE of the most vital problems in the manufacture of steel at present is the occurrence of the defects that have been popularly termed "snow flakes," "flakes," or "scabs." Particularly is this the problem of many manufacturers who during the past 2 yr. have undertaken large-scale production for the first time. A study of the microstructure of such defective material throws considerable light upon the nature of these defects and is essential before measures may be taken for the elimination of the defects. Flakes do not appear to be found in the plain carbon steels; they have been found, however, in abundance in some of the simple alloy steels that are being used in such vast quantities; viz., nickel steel of the approximate composition, 0.40 carbon and 3.5 per cent. nickel, and in the chrome-nickel type. The present article summarizes the characteristic features of defective steel of the flaky type as they have been found by laboratory study of numerous specimens, and it aims to show the conditions within the metal that are favorable to the occurrence of this type of defect without entering into the details of mill practice (size of ingot, design of molds, rate of cooling, distribution of cooling stresses, etc.), all of which conditions appear to play a role in the production of these defects.

Jan 2, 1919

By S. L. I. Chan, M. Z. Quadir, D. C. Austin, P. J. Hazell, A. Chen, A. A. H. Ameri, D. East, J. P. Escobedo, M. A. Bevan, A. D. Brown

The microstructure and mechanical response of additive manufactured Ti64 under compression and tension has been investigated. Quasi-static and dynamic experiments were conducted on electron beam powder bed Arcam A1 (EBM) and blown powder laser Optomec LENS MR-7 (LMD) additive manufactured specimens. Hot isostatic pressing (HIP) was conducted on both of the additive manufactured specimens and results were compared with as-received specimens. Digital image correlation (DIC) was utilized to observe the in situ development of deformation fields during tensile loading. Optical microscopy was conducted on pristine and deformed specimens to examine the microstructure of the specimens. HIP treatment reduced the porosity by *90% with a concomitant increase in hardness by 40%. The results from tensile experiments show that additive manufactured Ti64 display a higher values for the yield stress, hardness, and ultimate tensile strength than conventionally manufactured Ti64. Under quasi-static compression, it was observed that EBM specimens exhibit a higher yield strength and ultimate tensile strength than LMD specimens.

Mar 1, 2017

By A. R. Farkoosh, J-P. Fortin, M. Pekguleryuz, S. Bagherpour

"Titanium aluminides are structural intermetallics which offer an attractive combination of high temperature strength and light weight. For such properties, these intermetallic alloys have become front-runners in replacing nickel-based superalloys used for several high temperature applications. These alloys are produced from metallic titanium, aluminum and master alloys involving an expensive and difficult process. A low cost alternative to current industrial production method is the new modified aluminothermic process which directly reduces titanium oxide (TiO2) to titanium aluminides. Nevertheless, this process has itself significant challenges in achieving alloys free of oxide inclusions; the close densities of the slag and the titanium aluminides makes slag/molten metal separation a challenging task. Usually, the alloy produced requires a second refining step. In this study, thermodynamic calculations based on CALPHAD method were performed to determine the solidification path and an attempt has been made to develop a criterion to increase the density deference between the slag and the alloy by alloying with appropriate elements. Furthermore, scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were utilized to examine the microstructure and phase selection of three Ti-Al alloys produced by the aluminothermic reaction, including the as-cast, refined in a controlled atmosphere and inert-gas-refined alloys. The composition range of the alloys studied was restricted to the a2-Ti3Al + ?-TiAl phase field (Ti-30Al) in the binary Ti-Al phase diagram leading to a lamellar structure with different complex intermetallics as shown in Figure 1.INTRODUCTIONTiAl based alloys are promising structural materials for high temperature aerospace and automotive applications. This is due to some attractive properties such as low density, high specific strength, high specific stiffness and high temperature strength retention (Wen-bin, Xue-wen, Hong-fei, & Yong-feng, 2011). These alloys have become leading candidates to replace Ni-based super alloys in gas turbine engines. Replacement of Ni-based super alloy parts with titanium aluminides is expected to reduce the structural weight of high performance gas turbine engines by as much as 20–30% (Kothari, Radhakrishnan, Sudarshan, & Wereley, 2012)."

Jan 1, 2016

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011