Search Documents

By P. C. Beuria

Iron ore concentrate contains different mineral phases viz. hematite, magnetite, goethite, kaolinite, and gibbsite. Presence of some of these phases like goethite, kaolinite, and gibbsite contribute to the loss on ignition (LOI) content of the sample. Iron ore fines (pellet feed) are pelletized for utilization in DRI & BF processes. In the present pelletization technology i.e., straight grate and grate kiln processes, the LOI in the ore should be within the range of 2.0-2.5%. LOI content in the iron ore concentrate is found to be more than 4% after beneficiation of low-grade iron ore. It is therefore difficult to produce good quality pellet because of high LOI content. The LOI content of the sample is a detrimental factor in the pellet making. For effective pelletization, the LOI content in iron ore fines needs to be reduced before pelletization. It can be reduced by fluidized bed roasting. The objective of present work is to understand the kinetics of removal of LOI from iron ore fines. The effects of bed depth, temperature, and residence time on reduction of LOI content in iron ore fines were studied using muffle furnace. The process of roasting was carried out at four different temperatures varying from 400 to 950 °C with a variable residence time of 30, 45, 60 & 75 minutes and at bed depths of 16, 32, 48 & 64 mm. In all instance of experiments carried out, one of the parameters was kept constant. It was observed that at 850 °C and 30 minutes of residence time, there was sufficient removal of LOI in static bed condition even at a high bed depth of 64 mm. Keywords: LOI, pellet feed, fluidized bed roasting, goethite

Sep 1, 2012

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012

Kinetic Study on the Leaching of Vanadium from LD Converter Slag Using Sulfuric Acid In order to reduce the environmental impact due to land disposal of LD (Linz-Donawitz) converter slag from steelmaking plant and to valorise this waste material, an acid leaching study was carried out to assess the effect of several parameters on the kinetics of vanadium dissolution. The characterisation and morphology of the feed investigated using XRD, XRF. The factors influencing leaching vanadium such as particle size, temperature, slurry density and the concentration of sulfuric acid were investigated and optimised. The maximum vanadium recovery about 95 per cent achieved at 70¦C, S/L: 1/15, acid concentration: 3M and for 150 minutes of leaching time. The dissolution of vanadium in sulfuric acid shows that there are two stages in the kinetics of leaching. At the first 15 minutes, there is a sharp increase in the amount of vanadium extracted and at longer leaching time, the extraction increase slightly. In the present work, the shrinking core model (SCM) was used to describe the acid leaching of vanadium compounds. A summary of the controlling regimes in the SCM are examined below for short time (less than 12 min.) and long time (more than 30 min.) stages. So, it was found that the kinetics of leaching in both stages is controlled by solid product diffusion regime.

Sep 13, 2010

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By R. Cheng

The kinetics of the solvent extraction of ythium from HCl solution with mono-2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester (HEHEHP) have been studied using a rotating diffusion cell (RDC). The effects of rotation speed, pH, ymium and extractant concentrations and temperature on the rate of extraction were examined. The rate of extraction of ythium appears to be controlled by an interfacial reaction of metal ion and extractant. The concentration of the latter is determined mainly by diffusion through the membrane. The contributions of the rates of diffusion in the diffusion layer, diffusion in the membrane and chemical reaction at the interface to the overall rate have been calculated on the basis of a kinetic model.

Jan 1, 1992

By Bern Klein, Richard W. Lawrence, Scott Frostad

A laboratory study was conducted to evaluate the effects of various kinetic test protocols on sulfate production, NP depletion and time to acidity. Six test protocols were evaluated including standard humidity cells, non-aerated cells, tall cells, shaken cells, simulated precipitation cells, and NP depletion columns. The study indicates that test protocols which disrupt the oxidizing environment, such as extreme wetting and drying cycles, shaking the cells, or the high addition of acidic water will create an unnatural environment that affect the results. Trickle leach and non-aerated test protocols create an oxidizing environment that more closely represents field conditions and are therefore recommended.

Jan 1, 2000

By Bern Klein, Richard W. Lawrence, Scott Frostad

Laboratory and field scale kinetic testing was conducted to evaluate scaling up of laboratory data. Two 20- tonne (field) cells were monitored for internal temperature, pH, conductivity, volume and rate of flow, and water quality. On a surface are. basis, results showed sulfide oxidation rates obtained using 50-kg cells are more sensitive to changes in aeration than those from 1-kg cells. Correcting the laboratory oxidation rates for field temperatures with a pH 7 activation energy, which is in the field drainage pH range, returned oxidation rates an order of magnitude lower than the field cell rates.

Jan 1, 2000

By L. S. Gourevitch, E. B. Kremer, A. Y. Fidlin, Y. M. Katsman, I. I. Blekhman

A new kinetic approach to simulation of fracture is given. The main object of the simulation is forecasting transformation of ore lumps size distribution in squeezing of ore layer between two planes. The approach rests on fundamental principles of energy and mass conservation and on new ideas about fracture physics connected with fractal geometry. On this base an integro-differen tial equation of layer crushing kinetics is formulated. This equation is similar to well-known kinetic equation of grinding, but here we use elastic energy density in place of time as an independent variable while selection function is considered by us to be dependent on this variable. Properties of the equation have been investigated by us and its analytical solution has been found. It allows to compute simultaneously both the evolution of the size distribution process of squeezing and force-displacement diagram. Results of theoretical calculations provide a good fit with experimental data.

Jan 1, 1995

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By David Langberg

Recovery of dissolved copper from discard slags is a critical consideration affecting the economics of copper smelting. Slag cleaning is frequently carried out in electric furnaces, however reduction by injection of natural gas in a holding furnace may offer a lower cost alternative in some circumstances. As the residence time of the injected gas is short, the factors controlling the rate of reduction need to be clarified in order to optimise the design of the slag cleaning furnace. A series of medium scale (200 kg) reduction tests to investigate the rate of reduction of copper-containing slags by injection of natural gas-nitrogen mixtures between 1150-1250C was carried out by CSIRO Minerals. The composition of the gas in the top-space of the reactor was found to be significantly more reducing than the slag, indicating that thermodynamic equilibrium was not established between the slag and the gas in the bubble plume. An apparent first order rate law was observed between the rate of oxygen elimination from the bath and the magnetite concentration of the bath. The dissolved copper concentration was closely correlated with the oxygen potential of the slag, suggesting a partial equilibrium between the dissolved components of the slag. The utilisation efficiency of the natural gas decreased as the natural gas flow rate was increased. The results of the tests tend to indicate that the rate is controlled by a mixed reaction kinetics/ mass transport mechanism. The work was supported by Xstrata Copper ? Mt Isa Mines.

Jan 1, 2006

By Allen Pratt, Guy Deschênes, Mike Fulton, Hai Guo

Calaverite is a gold telluride species, with the composition, AuTe2. Calaverite is usually characterized by an exceedingly slow dissolution rate in a cyanide solution. Cyanidation of a slurry containing synthetic calaverite (P90 of 10 microns) was studied to determine the leaching kinetics and surface reactions. Alkalinity, dissolved oxygen, lead nitrate and sulphide minerals (pyrite and chalcopyrite) were among the parameters evaluated. The reaction products at the surface of calaverite were documented using X-ray photoelectron spectroscopy. High lime concentration with lead nitrate and injection of oxygen produced the fastest leaching rates. New gold leaching mechanisms were identified which appeared to be related to the parameters selected.

Jan 1, 2005

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette&apos;s core. The measurement of the carbon content on the globules and the external iron layer is also presented.

Jan 1, 2003

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette&apos;s core. The measurement of the carbon content on the globules and the external iron layer is also presented

Jan 1, 2003