Search Documents

By T. E. Leontis

ONLY a limited amount of information has been published on the effect of thorium as an alloying ingredient in magnesium. McDonald13'2 showed that the addition of thorium in amounts up to 3 pct increases significantly both the ductility and the strength of rolled magnesium sheet. A recent publication by Sauerwald" indicates that thorium contributes strength and creep resistance at elevated temperatures to magnesium in both the cast and wrought states. The observations of Sauerwald are confirmed in this paper, which presents the results of a systematic study of the effects of compositional variation on the tensile properties, creep resistance, conductivity, density, and metallography of Mg-Th alloys containing up to 50 pct Th both in the sand-cast and in the extruded states. The effect of the addition of cerium to Mg-Th alloys is also reported. Experimental Methods The alloys studied in this investigation were pre.pared in small laboratory melts according to the melting practice described by Nelson4 as the crucible method. Electrolytic magnesium was used as the starting material to which the thorium* was introduced in metallic form. It was observed that the behavior of thorium in molten magnesium with respect to reaction with protective fluxes is similar to that of rare-earth metals. In order to obtain the highest possible alloying efficiency, it is necessary to use non-MgC1, fluxes and to apply all the precautions described by Marande6 for melting, alloying, and casting magnesium-rare-earth alloys. .Under these conditions it is possible to obtain an alloying efficiency in the range of 85 to 95 pct. The Mg-Th-Ce alloys were made with cerium of the highest purity available, not with the commercial product "misch-metal" which contains approximately 50 pct Ce. The total rare-earth content of this material was 97.1 pct, of which 0.3 pct was rare-earth metals other than cerium; the major impurities comprising the balance were iron and magnesium. The thorium and cerium contents of each alloy were determined chemically. Test bars 6% in. long with a 2% in. long reduced section of % in. diam were cast in sand molds using a four-baf pattern. In most cases, a 3 in. diam extrusion billet 10 in. long was cast in a steel mold from the same melt used for making the sand-cast test bars. For the higher thorium alloys, it was necessary to remelt the foundry scrap from the test bars in order to make the extrusion billets. The billets were scalped to a diameter of 2 15/16 in. and the ends faced to a length of 9% in. as limited by the size of the extrusion container. The alloys were extruded into % in. diam rod on a 500-ton direct-extrusion press. The details of the extrusion process are as follows: Billet preheat 925°F (2 to 16 hr) Container temperature 900 °F Die temperature 900°F Extrusion speed 10 ft per min Reduction ratio 36:1 Percent reduction 97.3 Alloys containing up to 10.2 pct Th were preheated at 925°F for 2 hr; all alloys with higher thorium contents were preheated for 16 hr. In order to establish the effect of extrusion temperature, billets of

Jan 1, 1953

By P. W. Ramsey, D. P. Kedzie

INCREASING demand for improved strength-weight ratios made on aircraft structures has resulted in a gradual increase in the tensile strength requirements for steels used in such applications. As the cyclic loads often are more critical than static loads, and the fatigue properties are generally the design criteria, the question arises as to whether an improvement in fatigue properties accompanies the increased tensile strength. The present investigation was undertaken to determine the relationship between fatigue and tensile properties for an aircraft quality steel in the 155 to 280 ksi (1000 psi) tensile strength range, using the Prot method of fatigue testing. Procedure and Results After preliminary work to establish proper heat treating procedures for this heat of aircraft quality electric furnace steel (a Ni-Cr-Mo-V steel," AMS- Prot Fatigue Testing Method—The determination of the endurance limit by the conventional Wohler method can be time-consuming and easily require 20 specimens when statistical variance is to be established. This is also true when endurance limit loads are determined on actual parts or subassem-blies, and the desirability of a reliable accelerated method has been evident for some time. The primary advantage of the Prot method of fatigue testing is in reducing the number of specimens and the time required for each test. Unlike the Wohler method, every Prot specimen tested con- tributes to the determination of the endurance limit, and the authors have been able to duplicate Wohler results obtained with 20 specimens with only half the specimens and a fourth of the total cycles. This new technique for defining the endurance limit was proposed in 1948' by Marcel Prot and consists of progressively increasing cyclic stress until fatigue failure occurs. By varying the load rate, a, a useful relationship is found to exist with failure stress, so that for steel the failure stress appears to

Jan 1, 1958

By Robert M. Yonco, Irving Johnson, Martin G. Chasanov

The thermodynamics of the cadmium-rich portion of the Pu-Cd system has been studied with a high-temperature galvanic-cell method. The partial phase diagram of the Pu-Cd system was determined. The existence of the intermediate phases PuCd11 (cubic BaHg11 structure, ao= 9.282) and PuCd6 (cubic, CeCd6 structure, a, = 15.59) was established. The existence of at least one other intermediate phase richer in plutonium was indicated. PuCd11 was found to peritectically decompose into PuCd6 and liquid at 406" * 2°C. The solubility of plutonium in liquid cadmium may be represented by the equations: (355' to 399°C) log (at. pct Pu) = 6.223 -4282T-1 (399° to 632°C) log (al. pct Pu) - 5.148 - 5277T-1 > 1.156 x 106 T-2 The free energy of formation values (kcal per mole) of the two intermetallic phases are given by the equations: (PuCd11), ?Gf= -45.9 + 35.7 x 10-3 T (PuCd6), ?Gf0- -39.27 + 25.86 X 10-3T The excess free energy (kcal per mole) of plutonium in liquid cadmium may be represented by the equation: -(-16.72 * 29.54 NPu) 10-3T in which Npu and Ned are the atom fractions of plutonium and cadmium. The thermodyanamics of the U- Cd and Pu-Cd systems are compared. THERMODYNAMIC information on systems of the actinide metals with low-melting metals, such as zinc and cadmium, is useful in the design of pyro-metallurgical processes for the purification of nuclear reactor fuels. The thermodynamics of the Pu-Zn,1 Th-Zn.2,3 U-Zn,4-5 and U-Cd6 systems have been reported. The present report on the Pu-Cd system concerns the liquidus composition in the cadmium-rich region, the characterization of the two most cadmium-rich intermetallic phases, and the thermodynamic properties of these intermetallic phases and dilute liquid solutions of plutonium in cadmium. EXPERIMENTAL Phase Studies. The liquidus composition was determined by analysis of filtered samples of the liquid phase withdrawn at a series of temperatures. The apparatus and procedure were identical to that used in the previous study of the Pu-Zn system.' Briefly. a sample of the melt was withdrawn into a tantalum tube fitted with a porous tantalum filter (30-µ pore). the entire sample dissolved in hydrochloric acid (to avoid errors due to segregation

Jan 1, 1965

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,&apos; the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.&apos;-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.&apos;-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

By R. W. Kraft, F. D. George, F. D. Lemkey

From a conszderation of the geometrically possible ways in which an array of lines or linear features in three-dimensional space can depart from a statistically random arrangement, a system was developed to describe and measure different types of anisotrypic arrangements of lines in opaque solids. The technique was applied to a specimen of unidirectionally solidified Al-Cwll, eutectic which contained microstructural imperfections termed lamellar faults. Experimental data obtained from photomicrographs of different facets of a grain of this alloy were then analyzed using this system. It was deduced that the defects, which are essentially linear in natuve, were predominantly parallel to one another but not parallel to the nominal growth direction probably because of some lateral heat flow during solidification. InGOTS of lamellar eutectic alloys which have been unidirectionally solidified under growth conditions which prevent colony formation consist of large elongated grains in which the lamellae are approximately parallel to one another. Deviations from a parallel lamellar structure within a grain are caused by extra lamellae which form occasionally during the solidification process. Three-dimensional analyses of such specimens have revealed that one extra platelet produces two defects, termed 1amellar faults, which can and do grow more or less independently of one another.&apos; The faults are analogous in many ways to edge dislocations in crystals. If a lamella of one phase is considered to be basically two-dimensional, e.g., a surface, then a fault can be defined as the locus of points which delineates an edge (or half the periphery) of one extra lamella as it grows and forms bridges and saddles in an otherwise parallel arrangement oi lamellae, Fig. 1. Were it not for the fact that bridges and saddles occur in the structure, the extra platelet could be defined as the unit defect and the concept of linear faults of positive and negative character around the periphery of the extra platelet would be unnecessary. If an extra platelet is merely inserted (actually it is grown in) between other parallel platelets, the fault line around the periphery of the extra platelet would circumscribe one and only one platelet, namely the extra one, and the faults would lie in a plane parallel to the lamellae. But when an extra platelet merges with adjacent ones and each side grows independently of the other, it is no longer topologically possible to delineate "the extra plate." A fault circuit which either closes on itself or passes out of the specimen still occurs although it no longer will be coplanar with the lamellae. In fact, it is usually not even Planar even if the lamellae are. Under these conditions a concept that a specimen contains N extra platelets of a given size per unit volume would be very artificial and consequently meaningless. Therefore, because of the topological complexity of the alloys, it was deemed necessary to define one-dimensional

Jan 1, 1962

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.&apos; For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By D. C. Jillson

THE data on the critical resolved shear stress for zinc single crystals published by Rosbaud and Schmid1 showed many irregularities, as seen in fig. 1. There have been subsequent investigations,2,3 but no one has repeated this work with a wide range of orientations, with specimens of a higher degree of purity and perfection, and with improved experimental techniques in order to determine whether these variations were entirely experimental or whether they might have been due, at least in part, to some feature of the mode of deformation not known or understood. Mathewson4 and others have long felt that the glide observed in a [100]* direction between two (001)* planes in the zinc lattice might be actually the net effect of many consecutive unit glides or movements in two alternating [210] directions (fig.

Jan 1, 1951

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.&apos; Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors&apos; laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By J. H. Waxweiler, L. C. Ikenberry, R. J. Bendure

Carbon which is present as insoluble carbides in austenitic stainless steels can be measured quantitatively by dissolving the steel in iodine-methanol and analyzing the residue for carbon. Severe sen-sitization was observed in Type 302 due to precipitation of only 0.003 pet carbon. Both cold work and the presence of delta ferrite caused a marked acceleration in rate of carbide precipitation. Carbide precipitation rates in 17-7 PH were stzulied for the austenite conditioning and also the aging heat treatment. CARBON and its compounds exercise a major influence on the properties of stainless steels and their response to thermal treatment. Sensitization in 18-8 type stainless steels has been the subject of numerous investigations throughout the years. Bain, Aborn, and utherford," and Binder, Brown, Frankss all studied the effects of heating austenitic stainless steels in the temperature range of 1000° to 1500°F. The primary purpose of most of these studies was the investigation of susceptibility to in-tergranular attack in acids due to these sensitizing heat treatments. Intergranular precipitation of carbides was always associated with intergranular attack but it was recognized2 that severe attack could occur with but minute quantities of precipitated carbide. Mahla and ielsen utilized the electron microscope to make a significant contribution in illustrating the appearance and method of growth of chromium carbides during sensitizing heat treatments. However, as they stated, their studies of residues could not be used to obtain a quantitative measurement of the amount of carbon which was actually precipitated. The aim of the present investigation was to devise a relatively fast, simple method for the quantitative measurement of carbides in stainless steel. EXPERIMENTAL WORK The initial investigations were made to determine the best means of separating carbides from the matrix. A number of dissolving media were tried using both chemical and electrolytic attack. Qualitative examination of the extracted residues by X-ray diffraction indicated that solution in iodine-methanol would furnish a good means of separation. Consequently, further work was pursued along this line. The method is quite simple. The sample in the form of millings or nibblings is dissolved in iodine-methanol solution at room temperature (6-g iodine, 25-ml methanol per g of sample). The insoluble residue containing the carbides is separated by suction filtration through an ultra-fine glass filter disc. This is a very fine filter medium that will retain particles as small as 0.1 to 0.2 p in diameter. After washing with methanol and drying, the filter disc and residue are placed in a conventional combustion carbon-tube furnace and the carbon determined gravimetrically. Using this technique it was found that reproducible insoluble carbon values were obtained. However, since such small amounts of insoluble carbon were obtained on Type 302 after sensitizatipn at 1250°F and 1500°F, the values were confirmed by a second method. In the second method the sample was dissolved with copper potassium chloride and filtered through a millipore paper. This treatment dissolves the matrix but leaves undissolved practically all of the carbon irrespective of how it is present in the steel. The amount of insoluble carbon present as chromium carbide is determined by calculation from the analysis of the residue for chromium and iron. The derivation of the formula used for this calculation is discussed later. The values obtained by the indirect copper-potassium-chloride method were in agreement with those obtained by the iodine-methano1 method. See Table I. It should be pointed out that the sensitivity of the direct combustion method is not too high when the amount of carbide present is small. This is due primarily to inherent blanks and to analytical errors such as weighing. For this reason it cannot be stated with any degree of certainty that there is a significant difference between values of 0.002 and 0.005 pct. Having confirmed that the iodine-methanol extraction gave a quantitative measurement of the precipitated carbides in Type 302, exploratory tests were conducted on Armco 17-7 PH stainless steel. Samples from commercial Heat 54807 were solution annealed at 2000°F, water quenched and heated at 1250" and 1500°F, and water quenched. The analysis of Heat 54808 is as follows:

Jan 1, 1962

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By Sidney Fischler

Large striation-free single crystals of bismuth have been grown from the melt by rapid freezing. Zone-refined bismuth, together with doping impurities if desired, is placed in a shallow flat-bottomed graphite boat and melted in air with a propane hand torch. The torch is then withdrawn in a manner which causes the melt to freeze direction-ally. Crystallization, which resuires only a few minutes, usually results in the formation of a single crystal even when a seed crystal is not used. Crys -tals of any desired orientation may be grown by using oriented seeds. Undoped crystals grown by this method have residual resistivity ratios greater than 200. THE growth of large single crystals of bismuth by either the Czochralski or horizontal zoning technique is not entirely satisfactory. Specifically, difficulties are encountered in producing single crystals of the required dimensions in all desired orientations, and striations caused by low-angle polysynthetic twins are frequently present in the crystals. In addition, both methods are time-consuming and require special apparatus of some complexity. A simpler method has now been developed for growing large striation-free bismuth single crystals of desired orientation in a short time. Fig. 1 shows a typical setup consisting of a rectangular graphite boat which contains zone-refined bismuth, a 1/8-in.-thick flat quartz plate which covers the entire inner bottom of the boat, and three additional quartz plates about 1/4 in. thick which are used to separate the bismuth from the graphite everywhere except at a small area at the left of the boat. The graphite boat is 1 in. high, and its sides and bottom are about 1/8 in. thick. The quartz plates should be smooth and clean. The graphite boat is heated from the right with a propane torch, as shown in Fig. 1, until the bismuth is completely melted. The melt has the shape of a triangle with a narrow neck at the apex farthest from the torch. The melt is frozen direc-tionally by gradually moving the torch toward the right, away from the boat. The bismuth in contact with the graphite, at the left end of the neck, freezes first. The freezing interface then moves down the neck into the main bulk of material, where it develops a convex shape ideal for the continuation of single-crystal growth. The interface continues to move through the melt until the entire bulk is solid. The entire procedure may be completed, in air, in a matter of minutes. The technique described almost always yields a single crystal whose basal plane is nearly perpendi,cular to the bottom of the graphite boat. In earlier experiments, in which the bottom of the melt was in direct contact with the graphite boat, single crystals were grown with basal planes parallel, perpendicular, or at some intermediate angle to the bottom of the boat. At times the orientation of the bulk of the material differed from the orientation of the material in the narrow neck. In these cases, a nucleation site initiated the growth of a differently oriented crystal, and the thermal conditions favored the new orientation over the initial one. The thermal conditions depend on a number of factors, including the heating technique, the placement, shape, and thickness of the quartz plates, the thickness of the walls and bottom of the graphite boat, and the quantity of bulk bismuth employed. All of these factors, plus the initial orientation and the presence and effectiveness of nucleation sites, will determine the orientation of the final large single-crystal slab. When a crystal of specific orientation is desired, an oriented section of a rapid-freeze crystal is shaped by spark cutting and grinding for use as a seed. To grow a doped crystal, the desired impurity is placed in the graphite boat together with the bismuth chunks and seed. Crystals doped with mercury, cadmium, lead, and selenium have been grown. The rate of freezing is so great that the distribution coefficient of any impurity approximates unity. On a gross scale, therefore, impurities should be more homogeneously distributed in rapid-freeze crystals than in Czochralski or zoned crystals. Because of the possibility of constitutional supercooling, however, it is quite possible that impurities are not homogeneously distributed on a microscopic scale in the rapid-freeze crystals. Generally the single crystal slabs which have been prepared are initially 5 to 7 mm thick. Thicker crystals may be obtained by using one of these slabs as a seed. The slab is placed in a graphite boat resting on a large aluminum block, either air- or

Jan 1, 1964

By Robert Parker

Measurements of the latent heat of transformation from a to 0 titanium were made using a pulse-heating technique. Rapid heating was accomplished electrically by discharging a low-inductance capci-tor hank through a thin-strip specimen. Both high-purity titanium and titanium containing 2700 ppm of 0 were studied. An electrical-resistivity technique and a plot of energy input us temperature rise were used to monitor the phase change. It was concluded that: 1) the latent heat of transformation is 800 i 48 cal per mole; 2) phase change occurred in less than 200 sec; and 3) the percentage phase change that occurs is linearly a function of the energy available for phase change. In addition, this experiment provides a simple and inexpensive method for determining specific heat of electrical conductors over large temperature ranges. The chief advantages of this technique over past pulse-heating experiments are: 1) static measurements of capacitor-bank voltage capacitance and specimen resistance can be made quickly and accurately to determine the energy supplied to the specimen; 2) the specimen is heated so rapidly (10 µ sec) that there is no appreciable heat loss during the heating. THE purpose of this paper is to illustrate the use of the capacitor bank as a tool for basic experimental investigations and to determine the rapid phase-change kinetics of titanium. The capacitor provides a number of unique properties: 1) rapid heating rates in the order of l09oC per sec can be obtained; heating rates as slow as l04oC per sec are available by merely adding a given amount of inductance to the circuit; 2) the energy input can be precisely determined and can be varied from several joules to millions of joules, depending on the bank capacitance and voltage; 3) the specimen can be heated uniformly through the thickness and length or non-uniformly, as desired; 4) the apparatus is simple and inexpensive and can be easily altered; 5) the form of the specimen can be wires, sheets, foils, rods, and cylinders; 6) there is great precision in the timing of events; 7) this technique may be readily used in conjunction with rapid cooling.

Jan 1, 1965

By Dol Duwez, R. H. Willens

A technique is described by which metastable alloy phases can be obtained by very rapid cooling from the liquid state. The results obtained so far have lead to; 1) extension of solubility limits beyond their equilibrium values, 2) new phases not found under equilibrium conditions, and 3) amorphous alloys. MANY new nonequilibrium phases have been found in alloys rapidly cooled from the liquid state. The technique used in these investigations essentially consisted of propelling a small molten globule of an alloy against the inside surface of a rotating copper cylinder. Since these original experiments were performed, the technique has been greatly improved. The purpose of this paper is to describe in detail, for the first time, a simple and efficient apparatus for producing foils of alloys which are rapidly cooled from the melt and to summarize some of the observations made on these alloys. I) FAST COOLING APPARATUS In the original fast cooling apparatus used by Duwez, Willens, and Klement,&apos; the alloy was melted in a graphite container having the shape shown schematically in Fig. 1. A shock tube was attached to one end of the graphite part to supply the pressure for ejecting the molten globule. The globule was received on the inside of a rotating cylinder located about 0.5 in. from the exit of the graphite container. The globule trajectory made an angle of about 15 to 25 deg with the tangent to the cylinder at the point of

Jan 1, 1963

By A. E. Powers, J. F. Libsch

THE simultaneous influence of time and temperature upon the tempering process in steel is well known. Hollomon and Jaffe¹ have expressed the effect of time and temperature upon the progress of tempering by a single parameter, T (c + log t); where T is the absolute temperature; t, the tempering time; and c, a constant characteristic of the steel and treatment. It was found that when hardness data for plain carbon and low alloy steels were plotted vs. this parameter, a master tempering curve was obtained which satisfied all the data for a given steel and a given hardening treatment. Roberts, Grobe, and Moersch² successfully applied the tempering parameter to various tool steels, including high speed steel for tempering times ranging from 6 min to 100 hr. The influence of tempering time and temperature upon the physical properties of high speed steel has also been extensively investigated.&apos;" Recently, the use of induction heating for very rapid tempering treatments has received attention. The authors% have shown that tempering treatments of only a few seconds duration may be successfully applied to plain carbon and low alloy steel. However, the influence of such short tempering treatments in high speed steel has not been explored. Since high speed steel is a highly alloyed steel exhibiting physical reactions during tempering that are often relatively slow and large in magnitude, it is an interesting steel for the study of tempering reactions. It was the purpose of the present investigation, therefore, to study the early progress of reactions leading to secondary hardness in high speed steel, type 6-5-4-2, and to determine if induction-tempering treatments of a few seconds duration are able to produce results equal to those of more conventional long-time tempering cycles. Experimental Details The chemical compositions for two different heats of W-Mo high speed steel used in this study are given in Table I. Table II summarizes the heat treatment given various groups of specimens cut 21/2 in. long and centerless ground to ¼ in. diam. Hardening treatments consisted of preheating to 1600°F (870°C) for V2 hr and then oil quenching from 2250°F (1230°C). Heat I was subjected to the high temperature in a salt bath for 3 min, while specimens of heat II were austenitized in a carbon-block muffle furnace for 10 min. Specimens of series E were immediately refrigerated to — 318°F (— 195°C) in liquid nitrogen following the hardening treatment to transform the major portion of the retained aus-tenite. Specimens of series F and G were subzero cooled to — 100°F (-75°C) in a dry ice-alcohol mixture. Induction tempering was performed with a Lepel high frequency converter operating at a frequency of approximately 300,000 cycles per sec. Heating cycles were controlled and recorded for each specimen using a chromel-alumel thermocouple, percussion welded to the surface of the specimen, and a modified high speed instrument with a timer previously used and described.&apos; Temperature oscillation of the specimens, while being held at the tempering temperature, was ± 15°F (8°C). Tempering Treatments: After hardening, specimens were tempered between 900" and 1500°F (480" and 815°C) to study the progress of retained austenite decomposition and secondary hardening. The specimens tempered in salt for 1 hr (series C, G, and I) were considered to represent conventional treatment and are used for comparison with rapid tempering treatments. Several induction-tempering cycles were employed: 1—flash tempering, i.e., induction heating to the tempering temperature and immediately cooling (series A, E, and F); 2—induction heating for 60 sec at temperature (series B); and 3—double-induction tempering by two successive heating and cooling cycles (series D). All specimens tempered by induction were heated at an initial rate of 450°F (250°C) per sec except those of series E, which were heated at an initial rate of 1300 °F

Jan 1, 1952

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper&apos; some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 &apos;/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By S. E. Haszko

SEVERAL new XGa2 intermetallic compounds, Table 1, where X is a rare earth, having the AlB, structure were prepared as part of a continuing study of the magnetic and structural properties of rare-earth alloys.&apos; In this note, the crystallographic results of these compounds are presented. Chart, Eq. 121 for the data in Fig. 1 can be adequately represented by The corresponding standard free-energy change is AF; = -4.576 T log K = -20,900 + 10.20T [5I At low nitrogen concentrations the ratio of mole fraction to weight percentage is a constant so that the mole fraction X of nitrogen is given by X = 0.0392 [%NJ. At low values of X, the activity and the concearation approach each other, hence K, = 0.0392 K,, where K, is expressed in terms of the mole fraction of nitrogen. Hence Eqs. [4]. and [5] become

Jan 1, 1962

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels&apos; and with an Fe-Ni-Mn alloy&apos; in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova&apos;s isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954