Search Documents

By W. B. Mather

A SURVEY of the technical literature concerned with oil well drilling methods and particularly with rate of penetration by various cutting media on different types of rock provides a mass of conflicting data. This is especially true with respect to, (1) the relative efficiency of diamond, rotary and percussion drilling operations; (2) the costs of the various types of drilling; and (3) the hardness factor of various types of rock and cutting media. The latter is the particular phase of the subject discussed here. The cause of the confusion may be attributed partially to a lack of 'basic knowledge concerning the physical properties of the cutting media and of individual types of rock. It is also due in part to a general lack of uniform standards in the industry for evaluating the hardness versus drillability of rocks while possible errors in interpretation by the authors of the various papers pertaining to the subject may be an additional cause of misunderstanding. The hardness of a mineral is defined by Dana' as "the resistance which a smooth surface offers to abrasion." Webster' states that hardness is "the cohesion of the particles on the surface of a body (as a mineral) as determined by its capacity to scratch another or be itself scratched." Rock hardness, although not usually defined in publications describing rocks, is assumed to be the same as the minerals which compose the rock or the resistance of the rock to abrasion. Drillability of a rock may be defined arbitrarily as the rate at which rock is penetrated by a definite type of drilling tool with the assistance of a specific type of cutting surface or medium and under speci- fied conditions as to speed of rotation and applications of pressure. Eventually the term penetrability may have to be employed to include any method of making boreholes in rocks, since methods other than those using conventional cutting surfaces are already in operation. A case in point is the jet piercing methoda which employs an oxy-acetylene flame as a means of penetration. The word hardness as used by the drilling fraternity has a variety of meanings which depend upon the type of drilling method employed. For example, in diamond drilling, hardness is interpretated as resistance to abrasion. In percussion drilling the term implies resistance to impact or indentation, while in rotary drilling, hardness is considered anal-agous to compressive strength. The three types of hardness—abrasion, impact and compression—are conflicting variables for different types of rock. Nevertheless, the term hardness is applied indiscriminately by the industry for the resistance of rock to penetration by any type of drilling technique. Abrasion Hardness Since 1818, Moh's scale of hardness, although only relative in nature, has been accepted universally as the method of measuring mineral and therefore rock hardness. In 1933, Ridgway, Ballard and

Jan 1, 1952

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By Paul H. Price, John P. Nolting

The history of the salt industry in West Virginia dates back nearly two hundred years; howTever, the history of salt as an important raw material for the chemical industry is much more recent. The earliest record of West Virginia salt was in 1753, when a raiding party of Shawnee Indians attacked frontier settlements in Virginia taking captive a number of the pioneers. One of these, who later escaped and returned to her friends, described how the Indians camped at a salt spring on the banks of the Kanawha River and evaporated the water to obtain a supply of salt to take back to Ohio with them. Settlement of the Kanawha Valley began in 1774, that same year the Battle of Point Pleasant ended the Indian's power in the Ohio Valley; and settlement of the Kanawha Valley progressed rapidly with a consequent increase in the importance of the Kanawha Licks as a source of salt. In those days the evaporation of the brine was a family matter for which the family wash-kettle was commandeered. In 1797, Elisha Brooks erected the first salt furnace in the Kanawha Valley. It consisted of two dozen small kettles set in a double row, with a flue beneath, a chimney at one end, and a fire bed at the other. He obtained his brine at a depth of 20 to 30 ft by sinking hollow logs, called "gums" into the salt lick and dipping the brine with a bucket. His production was about 150 lb a day and sold for 8 to 10 cents a pound. In 1806, the Ruffner brothers, David and Joseph, prospected for and drilled the first well in America using a spring pole and steel chisel bit. After several failures they succeeded, in 1808, in drilling to a total depth of 59 ft where they secured a good flow of strong brine. Most standard drilling tools, jars, casing, and practically all the basic oil well drilling machinery now in use, were developed in the drilling of salt wells. To evaporate this brine, the brothers built a wood-burning furnace similar to that of Brooks but with a better arrangement and with more and larger kettles. When production was started they reduced the price of salt to 4 cents a pound. By 1817, there were some 30 salt furnaces in the Kanawha area. It was in this year that bituminous coal first was used as an industrial fuel. David Ruffner again pioneered the way by converting his furnace for the consumption of coal. This year also brought about the formation of the first trust which controlled production and set a price of 1 cent a pound for the salt.

Jan 1, 1950

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By M. A. Goudie

The deposits occur in a large salt basin of Middle Devonian age. The potash, the final deposit in the salt basin, results from several interrupted cycles of evaporation and dessication. The deposits are extensive, and, at first glance, relatively undisturbed. With more and more wells being drilled, it has now become evident that salt solution has played a large part in changing the original deposits, resulting in some cases in partial to complete removal of the potash and the underlying halite. The most dominant factor in the removal of salt by solution appears to have been tectonic movement and consequent faulting, probably of relatively minor dimensions but of major importance. Evidence which indicates the tilting of the evaporite basin to the north and northwest is shown by the changing pattern of the basin during succeeding eras of potash deposition. The potash minerals of most importance economically are sylvite and carnallite. Reserve calculations indicate that 6.4 billion tons of recoverable high grade potash in K2O equivalent exist in the basin. The Devonian salt basin, which contains the Saskatchewan potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota (Fig. 1). The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 285 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis, and Prairie Evaporite Formations. The Ashern formation, with an average thickness of 30 ft, sometimes called the Third Red Bed, consists of dolomitic shales and shaly dolomites. The Winnipegosis, is a reef-type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The thickness varies from 50 to 250 ft. The Prairie Evaporite formation, varying from 0 to 600 ft in thickness, consists of halite with interbedded anhydrite and shale, with considerable amounts of potassium salts in the upper part of the formation. The potassium salts are chiefly chlorides, although very minor occurrences of sulfates have been re- ported. The anhydrite beds do not appear to be continuous, although generally one or two bands of anhydrite underlie the lowest potash zone and are used as marker horizons. The shale occurs as seams interbedded with the salts, as large irregular inclusions in the salts and as very fine particles in intimate mixture with the salts. The Prairie Evaporite Formation is overlain by the Second Red Bed member, the Dawson Bay Formation and the First Red Bed Member of the Manitoba Group, listed in ascending order. The Red Beds are shales which vary in color from red to green, maroon, grey, grey-black, and reddish purples. They serve as marker horizons for coring the potash. The Second Red Bed averages 14 ft in thickness, the First Red Bed 35 ft. The Dawson Bay Formation, which everywhere overlies the First Red Bed and the Prairie Evaporite Formation in the area under discussion, is a reef type of carbonate, in some places limestone, in others limestone and dolomite, with vugular to pinpoint porosity averaging 130 ft in thickness. In some parts of the area, it has a salt section near the top of the formation, usually with interbedded shales and limestones. In other parts of the area, it is waterbearing and the salt is absent. Detailed mapping has indicated that the areas in which the Dawson Bay is water-bearing are areas which have been disturbed by faulting. Where the Dawson Bay is salt-bearing, the porosity has been plugged by salt. The total thickness of the salt varies from between 600 to 700 ft in the center of the basin to zero at the northern edge of the basin (Fig. 2).* The salt-free area in the center of the Province is believed to have resulted from removal of salt by solution. Evidence from several wells suggests that salt removal has been a continuing process from the time of deposition to the present day. One well drilled between the Quill Lakes for potash information encountered

Jan 1, 1961

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By E. W. Greene, J. B. Duke

This paper deals with the application of froth flotation techniques to the beneficiation of kaolin clay and phosphate slimes, two very fine particle sized materials. The kaolin problem involves the removal of a small amount of a contaminating mineral (anatase), while the phosphate problem involves the concentration and recovery of a much larger percentage of apatite. Due to these differences, and also different response to flotation, the two problems are discussed in separate parts of the article. An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. 1. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casa-grande1 using a long arm centrifuge to obtain equiva- lent spherical diameters down to 0.2 p on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 p, while the crude kaolin is 509 f'lner than 1.4 p, and the fine fraction 50% finer than 0.46~. For comparison 53 p on the horizontal scale would represent Stokesian diameters which would just pass a 325-mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 times the screen opening. 2 Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 p particles, 0.77 for 3p, 1.65 for 1.4 p and 5.0 for 0.46 p particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate-like particle shapes.

Jan 1, 1962

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By S. Brunauer

The hydration of portland cement is treated as a chemical reaction and the changes in matter, in energy and the rate of change of the process are discussed, Portland cement is a mixture of four major and at least as many important minor constituents. In the hydration process, the four major compounds (trical-cium silicate, dicalcium silicate, tricalcium alumi-nate and tetracalcium aluminoferrite), plus gypsum and water form five or six new compounds. In spite o the great complexity of the reaction, considerable progress has been made in its understanding, primarily with the help of such research tools as X-ray diffraction and electron microscopy. The rate of the reaction can be followed by direct and indirect methods of measurements. The effects o composition, particle size (or specific surface), temperature and water-cement ratio on the rates of hydration are discussed. The hydration of portland cement is a chemical reaction accompanied by such highly important physical phenomena as heat evolution, setting and hardening. It is a vast and complex subject, on which hundreds of papers have been published. At the time of the writing of this paper, in October 1962, a two-volume book, which alone contains dozens of papers pertaining to cement hydration appeared in print.' The present paper deals with a few aspects of this vast subject, and the selection was not easy. The work reported here deals with some of the most recent investigations in the field. In any chemical reaction, the physical chemist is primarily interested in three things: changes in matter, changes in energy and the rate of change of the process or the speed of the reaction. This is true also of the chemical reaction between portland cement and water, and all three aspects of the reaction will be discussed. These three aspects are of vital interest to the engineer as well. Portland cement is not a cementing material — the hydration products, the new materials which form in the reaction, have the cementing action. The energy changes manifest themselves in a considerable evolution of heat, which may be useful or harmful. It is useful, for example, in winter concreting, but in very large concrete structures like dams, a large evolution of heat, which cannot be easily dissipated, may produce distress in the structure. Primarily for such a purpose was the Type IV or low heat portland cement developed. The speed of the chemical reaction is important because it determines the time of setting and hardening. The initial reaction must be slow enough to permit placing of the concrete before setting occurs. On the other hand, after the placing of concrete it is often highly desirable to obtain as rapid chemical reaction as possible. For this purpose the Type 111 or high early strength portland cement was developed. CHANGES IN MATTER Portland Cement: In a basic investigation, before one begins to study a reaction, one either knows the quantities and compositions of the starting materials, the reactants, or one determines them. This is obvious; the chemist expresses the changes in matter that occur in a reaction by a chemical equation, which has the quantities and compositions of the reactants on the left side of the equation and the quantities and compositions of the reaction products on the right side. The first question is then what to put on the left side of the equation in the reaction between portland cement and water? It is not very easy to answer this question. Portland cement is not a single chemical compound but a mixture of many compounds. Four of these are considered the major compounds, and at least four of the minor compounds also play important roles in the hydration reaction. In order to avoid complicating matters, the present discussion will be restricted primarily to the four major compounds, which constitute usually more than 90% of a portland cement. The relative amounts of these compounds vary from cement to cement. Actually not only the amounts but the compositions of these constituents also vary to some extent, but the variation in composition of the individual components will be neglected for simplicity.

Jan 1, 1963

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack. These products are of great potential value in many branches of industry as insulation materials, aggregates, fillers, abrasives, and additives. By proper selection of the perlite rock type and control of processing conditions, expanded perlite of a bulk density varying from about 2 to 20 Ib per cu ft can be • made. The physical properties of the particles comprising a product of a given bulk density also may be varied within wide limits of porosity, water absorption, and crushing strength. In general, crushing strength of expanded perlite increases in direct relation to increase in bulk density, but insulating value varies in inverse ratio to bulk density. The selection of a particular grade of expanded perlite for a given use as an aggregate is therefore always a compromise between insulating value, lightness, and friability. If porosity and water absorption are factors affecting the use of the material, factors other than bulk density are important. Some types of perlite rock tend to decrepitate excessively during expansion, resulting in a highly porous or even hygroscopic product of high friability relative to the bulk density of material produced. In general, treatment of any good perlite rock below the temperature necessary for maximum expansion, or insufficient time in the hot zone of the furnace for effective heat penetration to the core of the rock particles will result in some decrepitation and high porosity in the expanded product. On the other hand, exposure of the material to the temperature required for optimum expansion for a period of time slightly longer than that necessary for proper heat absorption will result in a slightly heavier product of extremely low porosity, i. e., a glazed surface. It is beyond the scope of this paper to describe in detail the rock types and processing methods used to produce the many types of expanded perlite in present use, or that may be produced to fill the present and future needs of industry. A few phases of the economics involved in processing and selling products made from this abundant and cheap mineral raw material, plentifully distributed in large and relatively accessible deposits in most western states and in other areas within economic shipping distance of large centers of consumption, will be treated with particular reference to the Los Angeles area. Relation of Balk Density to Use and Cost of Production Perlite differs from most other lightweight aggregates and fillers in that the raw material (perlite rock) may be quarried much as rock arid sand is mined, and then shipped into consuming areas as crude rock in open gondola cars at correspondingly low freight rates and handling costs. At processing plants in or near large consuming areas the rock is converted into relatively fragile, very bulky products which in most cases are used within a short haul of the processing plant or enter into a manufactured product made at the site of the perlite processing plant.

Jan 1, 1950

By Elliot P. Rexford

IN the early days of concrete construction, the question of quality of sand or gravel to be used as aggregate in concrete was given little or no consideration. If the construction engineer had sufficient quantity for his structure within a reasonable distance, he was contented and gave no thought to the possibility that the material might have adverse physical, chemical, or thermal properties which could cause future deterioration of his concrete and possible failure of his structure. Today a very different situation exists. With the building of larger and larger concrete structures, with a longer and longer life expectancy, the quality of the aggregate material has become of major importance. Even in small concrete structures aggregate quality cannot be passed off lightly and the quality of the aggregate must be such as to give the anticipated life without costly maintenance. The first question to arise in the selection of an aggregate is what makes a sand or gravel suitable or unsuitable for use in concrete, and how can its quality be judged. No one rock type can be depended upon to furnish sound durable material in all instances. Granitic rocks, for example, make very satisfactory aggregates in some cases, but they are among the most unsuitable of materials when they are fractured, weathered, or highly micaceous. Limestones make excellent concrete aggregates on the one hand, and on the other they may be unsound and lack durability if they contain appreciable clay, they may have a harmful chemical reaction with the cement if they contain amorphous silica, or they may have thermal characteristics which make them highly unsuitable for use in concrete. Each rock, gravel, or sand must be proved on its own merits for the particular job under consideration. The selection of suitable aggregate materials may be divided into two major phases, the geological phase which is carried on largely in the field, and the testing phase which of course is a laboratory problem; both are important. Very often the geological phase alone is sufficient for the selection of satisfactory aggregates for minor structures but for major structures both phases must be thoroughly investigated. Geological Phase In the southwest part of the country nearly every major rock type, igneous, metamorphic, and sedimentary, may be found with all imaginable intermediate phases and in all imaginable stages of alteration. Frequently very different rock types, different as to geological age, composition, and condition occur very close together. Alluvium and stream-bed sands and gravels will consist of many different rock types and even ledge rocks may vary radically as to texture and composition within the area of a quarry site. Some of the rocks make suitable aggregate materials whereas others are highly deleterious in concrete. Too often the good and the bad occur together and more than ordinary caution is required in aggregate selection. Aggregate Sources: Concrete aggregates are usually obtained from stream-bed sands and gravels or from ledge rocks. Each has certain favorable and unfavorable characteristics and it is sometimes necessary to investigate both types to determine the most suitable source for a specific structure. Stream Beds: The predominant sources of aggregate materials in southern California and Arizona are stream beds. Vast quantities of sands and gravels are brought from the mountain ranges by the rivers during times of flood but most of these streams are dry a large part of the time and hence these deposits make easily accessible sources of aggregate materials. From many standpoints stream-bed materials make very acceptable aggregates. The gravel pebbles and the sand grains are

Jan 1, 1951