Search Documents

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By Noreen D

At Bougainville Copper Limited comparison testwork was conducted between "horizontal" cycloning and conventional vertical cycloning. Horizontal cycloning reduces circulating load and allows increased ball mill throughput. Cyclone efficiency is the same or better as a result of the reduction of fines short-circuiting to the underflow. Operationally, horizontal cyclones are less likely to suffer from blocked spigots and high cyclone feed pump sump levels. Cyclone feed pumping power is reduced. High horizontal cyclone underflow density provides the option to optimise grind by manipulating water addition to the ball mill feed.

Jan 1, 1988

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By H. D. Dahl, P. C. Thakur

This paper presents an analysis of a new tool for improved productivity in coal mining: the horizontal drilling system developed by Conoco/Consol. The analysis includes a brief description of the system; discussion of the three categories of advance exploration application of horizontal boreholes; and a survey of other special mining methods planned around long horizontal boreholes.

Jan 1, 1983

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By Bockhorst R. W, Christopher D. A

Over the past fifteen years, horizontal drilling in coal seams for advance degasification has become an established practice in the United States of America. Consolidation Coal Company pioneered the development of the horizontal drilling system and licensed the technology in the U.S. A. and to Du Pont (Australia) for commercial production. This paper discusses the most recent developments in the equipment design, especially the borehole telemetry system, known as the Downhole Drill Monitor (DDM).

Jan 1, 1988

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By W. E. Bruce, R. J. Morrell, James Paone

This chapter is a partial summary of an investigation by the U.S. Bureau of Mines (USBM) made in response to a recent request by the Assistant Secretary, Water and Power Development of the U.S. Department of the Interior, for a comprehensive review of horizontal boring technology related to underground power-line installation. This review is concerned primarily with 3 to 36-in. diam horizontal holes from several hundred to several thousand feet in length. An electric power system consists of three essential functions: generation, transmission, and distribution. The generation component includes the generating station and step-up substation; the transmission component includes the transmission line and stepdown substation at typical voltage levels ranging from 69 to 345 kv for underground lines and 69 to 500 kv for overhead transmission lines; the distribution component includes the distribution line carrying the commonly used voltages of 120, 208, and 240 v, the distribution transformer, and the line to the service customer.l The Federal Power Commission reports that 1600 miles of underground transmission lines of 60 to 345-kv capacity are now in service in the United States. By 1980, it is estimated that approximately 3000 miles of trans- mission lines will have to be placed underground.2 The cost of burying electric transmission lines underground in metropolitan areas, approximately 30 miles from the center of each of the most populated cities, will exceed $1.5 billion with the methods now available. The wide spread in unit costs of overhead and underground transmission lines narrows as right-of-way costs for overhead transmission in congested areas increase. Improved methods of underground emplacement will certainly reduce this difference in costs and even further favor underground emplacement. Also, in the future, overhead transmission lines will probably not be permitted in highly built-up areas.

Jan 1, 1970

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

By Wen Songlin

This paper presents an experimental program to investigate the behavior of a pile with wings under horizontal loads in sand at laboratory. The work focused on evaluating the lateral resistance behavior and the geometric effect of wing board on the horizontal resistance. Based on the measured data and observed phenomenon, the following behaviors have been observed: 1) A pile with wings is not only a powerful means to improve the horizontal bearing capacity of a pile foundation but also economy and feasibility; 2) The horizontal bearing capacity of a pile with wings increases with increasing of it?s wing board?s area; 3) The pile lateral capacity is also influenced by the wing board?s geometric shape. Under a certain soil and pile condition, there is a critical embedment depth of the wing board, which will yield the maximum horizontal bearing capacity. It was further observed that when the displacement of the pile head increases, part of the horizontal bearing capacity of the pile is developed by the so-called shaft?s anti-pulling capacity.

Jan 1, 2007

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997