Search Documents

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Clarence Zink

Aside from the mechanical properties and process of actual rock breakage, rotary drill bit performance is affected by several “post breakage” items: cuttings size, flushing air pressure, flushing air volume, cuttings load, drill hole geometry, etc. We all recognize that more efficient drilling creates bigger cuttings, more air pressure cleans the hole bottom better, more air clears the cuttings from the hole, and a better hole geometry allows cuttings to escape with a minimum of “regrind”.

Jan 1, 2006

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By McKenzie C. K

During a programme of explosive performance evaluation at Hamersley Iron, Mount Tom Price Mining Operations, the relative performances of a range of heavy ANFO explosives were compared during normal production blasting operations. In addition, a number of heavily instrumented single hole blasting trials were conducted with each product type. The blasts were monitored in terms of blasthole velocity of detonation (VOD), measured using multi-point plasma conductivity probes with up to 16 measurements per blasthole. Up to 16 blastholes were monitored in each production blast. The results of measurements show a marked difference in performance of all heavy ANFO products between single blastholes and full production blasts, indicating a significant degree of interaction between blastholes in production blasting. The interaction is shown to result in a loss of detonation pressure of explosive, and considered to lead to a loss of fragmentation. The degree of interaction is seen to increase with increasing emulsion content in the products, and is more pronounced in some explosive types than others. The paper presents the methods of measurement and analysis, and the results of monitoring, together with implications on blast design and application of heavy ANFO products.

Jan 1, 1990

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Rio Tinto Iron Ore (RTIO) manages eleven mines in the Pilbara region, Western Australia. Three of these mines have previously or are currently mining black shale that contains varying amounts of pyrite. Several new deposits currently being evaluated and existing mines that may progress below water table in the future, will also encounter this waste material. The black shale presents not just an acid rock drainage risk but also a spontaneous combustion risk. This paper presents the black shale management strategy and provides an overview of the relevant activities undertaken by RTIO. The strategy can be divided into two components which firstly involve defining the risk and secondly involve managing the risk. The mineral waste management plan is used to identify specific mineral waste hazards by:geochemical characterisation of waste material,undertaking mine site specific risk assessments,characterising the receiving environment,identifying sulfidic boundaries in geological and mining models,quantifying the amount of sulfidic material in medium and long-term mine plans, anddesigning and sequencing black shale waste dumps. Once a mine exposes black shale the Spontaneous Combustion and Acid Rock Drainage management plan is used and the major activities are: regular site meetings with a representative from every group that works with black shale;compliance with safe working procedures for site specific and detailed activities;regular training;the use of specific explosives to prevent premature detonation;ongoing geochemical characterisation;acid water management, monitoring and analysis;regular internal and external auditing of procedures and practices; andclosure planning assessments and preparations (ie cover trials, geochemical void modelling, geochemical waste dump modelling). The success of this holistic strategy is evident by the awareness of personnel within the business, thorough understanding of the geochemistry and by undertaking proactive management of black shale during mining. The strategy and management plans adopted by Rio Tinto Iron Ore have activities that other mine sites with potentially acid forming material may like to consider implementing.

Jan 1, 2009

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By Christian Leble, Dr. -Ing. Jakob Vogelsang, Dr. -Ing. Oksana Solt, Dipl. -Ing. Joachim Meier, Dr. -Ing. Wolfgang Orth

In the course of closing the gap between the Brandenburg Gate and Alexanderplatz, the Museum Island station was built by Implenia Construction GmbH. The tunneling for the platform hall took place on a length of about 106 m (347 ft) under the protection of a major ground freezing measure and crossed the Spree canal as well as the listed castle bridge. The approximately 20,000 m³ (4.54 E+06 US gal dry) frozen mass lay mainly in the Berlin sands. In order to ensure safe tunnelling and to protect the adjacent buildings, the planners had defined requirements for the mean freezing temperature and thickness of the frozen mass. For a reliable conclusion on the dimensions of the frozen mass, we used innovative temperature sensors as well as the new, web-based 3D measurement visualization and the associated site-specific evaluation software. The largely automated evaluation enabled a quick and reproducible determination of the temperature distribution in the frozen soil and its thickness in the relevant cross-sectional areas. The measurements were validated by thermal calculations using the Finite-Element-Method. Thus, an objective and clear assessment basis was available to ensure rapid coordination between stakeholders. The evaluations provide new insights into the temperature influences from tunneling, the application of shotcrete and the concreting of the inner shell. The newly implemented active thawing system is also an interesting innovation.

May 1, 2022

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By Steve Konieczki

[ ] Great Basin Gold Ltd. (GBG) owns the Hollister Mine and operates it through the wholly owned subsidiary Rodeo Creek Gold, Inc. The property is located in northern Nevada on the Carlin Trend gold belt within the historic Ivanhoe Mining District. The mine is located on the western edge of the Northern Nevada Rift, a major north-northwest trending structural zone that has localized middle Miocene volcanic rocks and numerous epithermal gold deposits. The precious metal deposits are low-sulfidation epithermal systems characterized by banded quartz veins with electrum and silver selenides. The Hollister Mine will employ the selective underground mining method of cut and fill. This will be combined with split shooting (resuing mining method) to optimize recovery and reduce dilution. The focus of mining will be on extraction of ?ounces? from the narrow-veins rather than trying to maximize tons. The initial drifts will be excavated along the strike of the vein and then capped with a substantial concrete sill pillar. Back stoping with hand held drills will be used to selectively mine the vein. The stopes will be backfilled with waste rock material. With every lift, an 18 inch concrete cap will be poured onto the backfill waste rock to prevent gold values from being lost into the fill. Targeted ore production rate will be over 400 tons per day. With current ore reserves, project life is estimated to be around eight years; however, Hollister geologists view the site as one of the most prospective systems for bonanza vein deposits in Nevada. Approximately $14

Jan 1, 2008

By Jesús E. Gómez

A recent bridge underpinning project provided a unique opportunity to obtain information on the load-deflection response of 260 hollow-core bar micropiles. All production micropiles were proof-tested to a maximum load of 125 percent of the design load. In addition, four verification tests were performed on sacrificial micropiles to at least two and a half times the design loads. This paper presents the results of the verification and proof tests performed for this project, and provides recommended values for design of hollow core bar micropiles in soils similar to those encountered. This work shows that hollow core bar micropiles provide a significant unit bond capacity in both granular and fine soils, which may be greater than that typically expected in pressure-grouted (Type B) micropiles. The hollow core bar system allows faster installation rates in the soil types encountered than other traditional micropile techniques, and can be installed with relatively simple quality control procedures.

Jan 1, 2007

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

Synthetic hollow microspheres have demonstrated reliable sensitization and detonation characteristics in industrial explosives for almost two decades. During that time, water gel formulations and use conditions have changed. The introduction of emulsion explosives has also dictated technical improvements in microsphere sensitizers. In contrast to microspheres, gassing or other sensitizing techniques often cannot satisfy the manufacturing and blasting characteristics required of today's explosives. This paper discusses the sensitizing properties of microspheres, formulating guidelines and quality considerations. Packaging, sampling, transfer, metering, mixing and pumping information is also provided.

Jan 1, 1990

By J. J. Forbes

Gentlemen : It is a pleasure to come to Glen- wood Springs to participate in this meeting of the Rocky Mountain Coal Mining Institute an organization created to handle chiefly the economic questions dealing with the coal industry of the Rocky Mountain District. I am not unmindful of the many and varied problems confronting the mining industry of this country which is so general at the present time throughout the United States. By reason of the difficulties experienced in marketing the product of your mines, there is all the more reason for greater economy and efficiency in production. No industry can be efficiently operated without giving due consideration to the safety of the employees. Safety and efficiency are inseparable for the success of any industrial enterprise. While the Bituminous coal companies of the United States are doing splendid work in the promotion of safety, yet our fatality rate is exceedingly higher compared with that of foreign countries, and with greater cooperative organized effort on the part of mine owners, mine officials, mine workers, and state and federal governmental agencies having jurisdiction, much more substantial progress can be made in the future and a greater economic saving .to the industry effected, not taking into consideration the greatest and most important phase of safety, which is the conservation of life and health of all those who are engaged in the occupation of mining. You are concerned with freight rates, marketing of coal and similar operating problems. Yet have you earnestly considered the vital question that plays so important a part toward the success of any mill-

Jan 1, 1926

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

By D. R. Schmitt, B. L. Jensen, T. J. Ahrens, C. L. Smither

The in situ elastic moduli of rock are measured holographically by a borehole instrument in marble and oil shale. A point force induced displacement field is recorded with double expo- sure holography. Data consists of a fringe pat- tern on the viewed hologram. The elastic moduli are determined by modelling of the fringe pattern. Only Young's inodulus is fairly constrained by the present data reduction. For an applied force of 520 [ ] 50 Newtons, a marble was found to have a Young's modulus of 56 [ ] 8 GPa, near an ultrasonically determined value of 48 [ ] 6 GPa. In an oil shale, an applied force of [ ]

Jan 1, 1986

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986