Search Documents

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By L. A. Harris

In the present study the open gradient magnetic separation&apos; (OGMS) method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy (SEM) and x-ray diffractometry (XRD) were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (-80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

Jan 1, 1981

By Gaballah I.

Elimination of arsenic, mercury and zinc from synthetic solutions containing H;\A.sD4. HgCI2 and ZnCI2 using modified barks was investigated. The pH range was varied from ?1 to 10. The initial concentrations of individual element were 10,100 and 1000 ppm. More than 99 % of mercury and 65 % of zinc cations were removed by the modified bark .. In this case, the modified bark reacts as a cation exchanger leading to the release of &apos; two protons for every HgII or ZnII fixed by this material. About 30 % of arsenic was eliminated from the solution. This &apos;low efficiency could be attributed to? the presence of arsenic ,as. anion. Decontamination of a treated industrial effluent containing 4 ppm of ion? metals was performed on a pilot plant scale by the modified bll(k. More than 70&apos;% of these ion metals were eliminated.

Jan 1, 1995

By Jr. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated flotation methods for recovering fluorite and byproduct beryllium from the Fish Creek deposit of Nevada. The preferred method includes (l) fluorite rougher and cleaner flotation, (2) de sliming at 20 micrometers, (3) muscovite flotation, (4) silicate flotation, (5) hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concentrate, Laboratory results showed that over 94 pct of. the fluorite was recovered in a concentrate containing 96 pct CaFz. Beryllium flotation produced .concentrates .containing in excess of 5 pct BeO with recoveries over 70 pct. A 1.00-lb/h continuous flotation unit was constructed to demonstrate this procedure,

Jan 1, 1985

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By Shadia J. Ikhmayies

"Cadmium sulfide thin films were prepared on glass substrates by the spray pyrolysis technique at a substrate temperature of 490°C. Some of the films were etched by HC1 in distilled water, others were heat treated in nitrogen atmosphere, and another set of films was first etched by HC1 and then annealed. Room temperature impedance spectroscopy measurements on the films were performed using coplanar geometry in the dark and in room light in the frequency range 20 Hz to 1 MHz. The experimental data were represented by complex plane diagrams and showed one well-defined semicircle in the high frequency region. Hence the equivalent circuit that models the CdS: In thin films was found to be a single RC circuit, which indicates the bulk conduction through the grains. The influence of treatments on the electrical properties was investigated.IntroductionCadmium sulfide (CdS) is a brilliant II—VI semiconductor material with a direct band gap of 2.42 eV at room temperature. It has many outstanding physical and chemical properties, which have promising applications in multiple technical fields including photochemical catalysis, gas sensor, detectors for laser and infrared, solar cells, nonlinear optical materials, various luminescence devices, optoelectronic devices and so on [1]. There are different methods to prepare undoped and doped CdS films, such as rf sputtering [2] chemical bath deposition (CBD) [3], pulsed laser deposition (PLD) [4], and spray pyrolysis (SP) [5-11]. Of these methods, spray pyrolysis represents the less expensive option, and can produce large area high-quality low cost thin films [12]."

Jan 1, 2012

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of&apos; calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By Xie Zhang, Chongyang Zhao, Qingyun Huang, Bing Xie, Xiaopeng Zhen

"Extracting vanadium from vanadium containing hot metal into vanadium slag by BOF is the main vanadium production process in China. In this paper, the influence of Si content in hot metal on the quality of vanadium slag is analyzed. Synthetic vanadium slag with different SiO2 content were melted at 1673 K and then cooled to 303K at the cooling rate of 3?/min. Optical microscopy, SEM, EDS and XRD were used to analyze the mineralogical phases and crystallization behavior of vanadium slag. The results show that vanadium slag mainly contains spinel phase and silicate phase; V is enriched in the spinel phases while Si is concentrated in Fe2SiO4 CaFeSi2O6 and (Fe,Mn)2SiO4 as silicate phase. The melting point of slag increases gradually with the addition of SiO2; whereas viscosity decreases with an addition of 15~19% SiO2 and increases with an addition of 19~27% SiO2.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys. The major vanadium products include FeV, V2O5, V2O3, VN and Al-V-Ti alloy. Furthermore, vanadium slags are mostly produced by oxidizing the elements in V-containing hot metal during a duplex refining process. Therefore, the process of removing vanadium from hot metal has its significance on the subsequent process[1].The extraction of vanadium is greatly affected by the mineralogical composition of vanadium slag[2], the distribution of the elements between the spinel and silicate phases and its physic-chemical properties. These characteristics of vanadium slag have been studied in some details. It has been reported that Si mainly exists mainly in the form of silicate which wraps the spinel crystals while small amount of Si stands as phosphorus quartz or diopside[2]. Chen et al.[3, 4] points out, when SiO2 content in vanadium slag increased every 1%, V2O5 decreased 1.48%. Moreover, silicate phases would embarrass the oxidation of V-containing spinels through decreasing the exposing probability[5]. Meanwhile, melting point and viscosity of vanadium slag has been greatly influenced by the SiO2 content. Therefore, this work attempts to analyze the above-mentioned questions systematically."

Jan 1, 2012

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia&apos;s demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia&apos;s titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By Daoxin Wu

Originated from(C4H9O)4Ti, nano--rutile TiO2 was synthesized by low temperature hydrolysis process in this paper. After being prepared by decomposing ammonium tungstate and covering on the surface of TiO2, TiO2/WO3 were characterized by means of X-ray diffraction(XRD), UV--vis difuse reflectance(DRS), fluorescence spectrum (FS). Results showed that with the increase of the supported concentration of WO3, the reflectance of DRS and the fluorescence spectrum intensity of TiO2/WO3 decreased accordingly, which indicated the powder?s increase in light absorbance and the decrease in luminescence respectively; with the increase of calcined temperature, the reflectance of DRS increased.

Jan 1, 2009

By Bradley C. Bockrath

Some thirty coals were evaluated for liquefaction activity under a mixture of CO and H2 at 425° C. The viscosity of the liquid products was taken as an indicator of the degree of liquefaction. It was found that the direct liquefaction of a particular coal may be beneficially influenced by the presence of pyrite. Active pyrites are often found in the native mineral matter of the coal itself. For example, subbituminous and bituminous coals and lignites of relatively high pyrite content were found to liquefy more readily than similar coals or lignites which were poor in pyrite. The reactivity of inactive coals could be improved by using blends with active, pyrite-rich coals. In addition, pyrite was effective when added separately as pyrite concentrates obtained from coal beneficiation operations. Various other iron- and sulfur-bearing additives were also effective when used in combination as added slurry-phase catalysts, including iron oxides and mineral residues derived from liquefaction of active coals. Under liquefaction conditions, pyrrhotite ( Fe I- x5) is formed from pyrite or from the iron oxides and many sulfur containing species. Pyrrhotite was shown to be a hydrogenation/dehydrogenation catalyst for tetralin but is not active for initiating a variety of free radical reactions that do occur when pyrite is heated with tetralin. The role of pyrite in coal liquefaction is complex and still not well understood.

Jan 1, 1981

By Grant E. Casley

Since 1970 Mount Isa fines Limited has made a significant increase in blister copper production from approximately 100,000 to 155,000 mt per annum and in fact 161,040 mt were produced in the calendar year 1974. Flowsheet developments including fluidised bed roasting and converter slag flotation are discussed, particularly their contributions to minimising major equipment changes in smelting and converting. The use of model- ling and simulation techniques for such an exercise is mentioned. The paper reports the alterations made to both equipment and operating techniques in the reverberatory furnace and converter sections to achieve the regular production of 250 mt of blister per converter day from a 41% Cu matte grade. The effects of flux composition on converting performance are highlighted. The air quality control programme is discussed in relation to its restriction of blister copper production.

Jan 1, 1976

By H. Jiang, S. Yang

"The main processes for nickel metallurgy in China consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte, grinding and flotation to separate nickel sulfide from copper sulfide and direct electrolysis of nickel matte. Systematic studies on the properties of electric furnace slag, smelting process for nickel matte, anodic process of nickel matte, cathodic process of nickel electrolysis have been done in our labs. In addition, an approach to a new hydrometallurgy process for nickel matte has been done. The feature of the new process is one stage acidic leaching of high grade nickel matte. The leaching solution could be purified by deposition way or by solvent extraction way. There are two leaching rate-determing steps, chemistry reaction-determing one at temperatures below 600C and diffusion-determing one at temperatures higher than 600 c. The acidic leaching fraction reacted dvaties with leaching time t according to the equation 1-(1- a ) 1/3=kt. The experimental data also show that the leaching reaction rate varies with concentrations of H+, Cl-, and it is also effected by copper sulfide and Cu++. The Cu++ ion can retard the leaching reaction due to forming a copper sulfide layer on the matte surface and the equation 1- 2/3 a. - (1- a: ) 2/3 akt can be used for the case. However the copper sulfide added into nickel matte can facilitate the leaching process. The research work for nickel metallurgy done by others in China has also been mentioned in this paper.Large scale production of nickel in China started in 1960s.The main processes consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte grinding and floatation to separate copper sulfide from nickel sulfide and direct electrolysis of nickel matte.To reduce nickel loss in slag a reseaech group organized by Jinchuan Company and Central South Institute of Mining and Metallurgy (now the Central South University of Technology) measured the viscosity surface tention density conductance melting point and structure of the slag(I).lt has been found that the physico-chemical properties of the slag depend on the components SiO2 ,MgO and FeO but FeO in the slag is too high and the statistic analysis of data from industry gave an equation to correlate the content of Ni in slag with the content of Ni in matte and the composition of slag again it was pointed out that the content of FeO in slag effected the loss of Ni in slag very much (2). The ratio (FeO+MgO) to SiO2shouid be less than 1.13 and the content of Fe3O4should be as low as possible but the reaction"

Jan 1, 1988

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By R. Altman

A Brookfield viscometer fitted with a stainless steel bob was used to measure the viscosity of industrial lead blast furnace slags between 1126 and 1298°c. Slag oxidation state was characterized by first annealing the? slag samples at 750°c in sealed copper tubes in order to precipitate magnetite crystals. The magnetite concentration was then measured on an Outokumpu Saturated Magnetic Analyzer. Using an Arrhenius-type equation, a viscosity model was developed by regression. The equation below accounted for 75% of the variability in the data used to generate the regression coefficients and, on average, could predict viscosity within ± 12% of the measured value. The greatest difficulty encountered in measuring viscosity was due to the occasional presence of solids in the slag which caused, at times, erroneously high viscosity measurements. Precautions to minimize this problem are outlined in the text.

Jan 1, 1985