Search Documents

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By O. I. Platonov

The experience that has been gained by MMC ?Norilsk Nickel? at its Trans-Polar Division (PD) operations since 1981 in the field of recovery of elemental sulfur from off-gas generated by the Vanyukov and flash smelting through its reduction by natural gas is briefly outlined in the present paper. The key challenge the operators treating off-gas originated from autogenous smelting are usually faced with is the presence of sulphur trioxide in it. Furthermore, air inflows along the entire gas flue increase oxygen concentration in off-gas, thus leading to over-consumption of the reducer (natural gas). Another issue attached to the methane technology is a low yield of hydrogen sulphide largely preventing efficient downstream Claus conversion of the gas. The new flowsheet for treatment of autogenous smelting off-gases including dry dust-cleaning followed by the gas reduction in homogenous reactor developed by OAO Gipronickel Institute on the basis of industrial-scale production of elemental sulfur in Norilsk is presented.

Jan 1, 2006

By I. Barin, G. Eriksson, F. Sauert

Computer-aided calculations using data bases and program systems are more and more needed for the rational development and optirnization of high-temperature processes. The calculation of mass and energy fluxes between different process steps as well as the determination of the chemical equilibria will be discussed, giving examples from nonferrous metallurgy. The simulation of a waste-material treatment process including high-temperature combustion and gas-cleaning systems will also be demonstrated.

Jan 1, 1988

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

By Vladimir Kislik

Competitive complexation/solvation theory of solvent extraction constitutes a general framework for interpretation and quantification of ion-molecular interaction data in extraction systems. Depending on extracting metal -- solvent affinity constant and metal concentration ratios, four possible stages of extraction behavior and interacting mechanisms, are considered. Affinity constant ratios are easily acceptable through the independent measurements of three-component systems. Once determined and tabulated, the affinity constant ratio data may be used in any system of interest. Mathematical descriptions of the results are introduced for different interactions. Active solvent (including water) concentrations in the organic phase and temperature are included to the quantitative consideration. The theory allows direct comparison of the complexing/solvating power (competition order) of various extractants, active solvents and diluents. As a result, predictions for the extraction effectiveness and selectivity are possible. Some metal extraction systems are analyzed on the base of the theory. Analysis gives a key for preliminary quantitative prediction of suitable extraction systems.

Jan 1, 2003

By W. John Rankin

Professionals, technical and non-technical, working in the mineral and metal commodity industries need to understand the concept of sustainability and its implications for the industry. Undergraduate courses have not done this well in the past. Much has been written in this field, and there have been great advances in understanding. However, much of what has been published is superficial and sometimes misleading, and there is as yet no coherent, single account that can serve as an introduction or overview for mineral industry graduates. This paper presents an outline which can guide readers in developing an understanding of the topic and its relevance to their work. Key references are provided, particularly those accessible on the internet, which will serve to introduce the reader to the important principles and understandings. The guide should also be useful to academics preparing students to work in the minerals and metal production sectors.

Jan 1, 2010

By M. D. Street

Lead and zinc production commenced in 1966 at Brunswick Smelting using the Imperial Smelting Process. In 1972 the blast furnace was modified to produce lead bullion only which was refined to corroding grade lead using conventional kettle refining techniques. Since 1972 consumption of lead concentrate and production of refined lead has doubled and this paper describes changes to operating and maintenance techniques which have contributed to this improvement. Reference is also made to improved environmental, health and hygiene practices at the smelter.

Jan 1, 1983

By Irsan Chandra

It is generally recognized that the gold thiosulfate leaching system requires the presence of copper and ammonia in order for acceptable leaching kinetics to be observed. However, the presence of copper and ammonia complicate the chemistry of the system as thiosulfate is rapidly oxidized by oxygen under these conditions. In addition, the environmental impact of ammonia would need to be considered before the adoption of this system. This paper describes fundamental studies into the thiosulfate oxygen system. The two reagents for this system are thiosulfate and oxygen, and leaching is carried out at pH < 7. It will be shown using electrochemical techniques that both the reduction of oxygen and the oxidation of gold-to-gold thiosulfate are hindered. Thus, if leaching is to work under these conditions, then both half reactions need to be improved. The use of additives, such as thiourea and lead have been shown to dramatically improve the oxidation of gold and the reduction of oxygen respectively. The leaching of gold in the presence of such additives is discussed.

Jan 1, 2003

By Alex Mezei

Experimental rheology data are needed to produce design criteria for mass and energy transfer processes. Large throughput plants operate under continuous flow mode. The capital cost is determined by the accuracy of the rheology data used for design. The operating cost is dictated by the energy required to sustain the flowing conditions of various process slurries. Typically, rheology investigations are carried out during the final stages of metallurgical testwork, which is too late to set the design criteria for the pilot plant. This leads to increased testwork cost, and sometimes lowers confidence in the quality of the data produced. In addition, the engineering and feasibility studies are often delayed because of the lack of pertinent rheology data. One of the objectives of this paper is to emphasize the importance of timely planning and execution of the rheology study, which is shown to be a critical component of the overall testwork program. Various applications are discussed, including elaboration of process and equipment design criteria. In this paper, the emphasis is placed on gold and nickel laterite hydrometallurgy applications.

Jan 1, 2003

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but industrially proven methodology utilizing nitrogen species catalyzation in the oxidizing pressure leach system may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a methodology for effective treatment of precious metals bearing chalcopyrite concentrates via partial oxidation at low temperatures and pressures will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 1999

By P. G. West-Sells

Recovery of gold from thiosulfate leachates can be accomplished by adsorption of the gold thiosulfate complex by a strong base resin. Two of the most significant impurities that can decrease this gold adsorption are tetrathionate and trithionate, which are produced as oxidation products of thiosulfate during gold leaching. This paper investigates gold adsorption on a strong base resin (Purolite A500C) as a function of the concentration of these impurities. It is shown that concentrations of tetrathionate and trithionate as low as 150 mg/L can decrease gold loading by an order of magnitude, and that of the two ions, tetrathionate has a stronger detrimental effect. The resin and solution gold concentration profiles were successfully fit using a Freundlich isotherm, which further shows the strong effect of tetrathionate. To counteract the decrease in gold adsorption by tetrathionate, a novel process was proposed. Sulfite was added to the solution to oxidize tetrathionate to trithionate, and a nitrogen blanket was added to ensure that no further oxidation of thiosulfate could take place. It is shown that by incorporating this process, gold adsorption was doubled from both synthetic and real gold thiosulfate leachates.

Jan 1, 2003

By A. Cullaj

During a period of 15 years the metallurgical and chemical complex of Elbasan containing more than 15 principal plants, producing cast-iron, steel, coke, nickel carbonate, nickel, cobalt, chromium and other products, discharged into air, river water and soil an extensive amount of hazardous wastes containing high toxic substances. A monitoring study for the levels of heavy metals in soils nearby the former plant is carried out for the first time. Very high levels (total and extractable) of contaminants such as nickel, cobalt and chromium are found in samples taken from a relatively vast territory including the city of Elbasan, situated 8 kilometres far from the plant. The most polluted samples present a total content of 1211.8 ? 2949.6 mg/kg Ni, 97.0 ? 181.2 mg/kg Co and 1358.7 ? 4130 mg/kg Cr. These levels exceed several times the phytotoxic thresholds and present a potential hazard for the inhabitants. This study, as part of a bigger multinational project on solid decontamination, will also serve to the possible application of the new phytoremediation and phytoextraction technologies, being developed in parallel in this project.

Jan 1, 2006

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

By K. P. Nishad

The origin of many casting defects can be traced at the mold filling stage. Entrapped air/gas pockets and oxide film formation are notable examples. In the present work, the mold-filling process is simulated using a mathematical model, built on a multi-physics based commercial package PHYSICA. The simulation code has the capability to solve multi-phase problems. The numerical model addresses a complicated dynamics of filling operation including free surface flow and subsequent flow behavior and is based on conservation of mass and momentum. The Free surface is modeled using the scalar equation method (SEM). The model is validated with benchmark experimental results from the literature. The role of turbulence and the pouring rate on variables affecting sites prone to oxide film formation are investigated using a simple but novel technique. Key findings of the work are presented.

Jan 1, 2006

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By Robert W. Bartlett

Hazardous metal contaminants in liquid and solid wastes and from ground spills are important environmental problems in many metallurgical production operations. Acid rock drainage, from mines and huge quantities of permeable mine waste, is probably the most ubiquitous example. Fixing mine waste contaminants in situ has been practiced, using sulfate reducing bacteria (SRB) and organic reagents as electron donors to create anaerobic conditions and precipitate metal sulfides. Aqueous solutions of sugar and alcohol have been percolated into mine wastes with good results. However, maintaining anaerobic conditions permanently is unlikely, as these solutions are eventually washed out of solid waste and contaminated ground by inflow of either groundwater or meteoric water, allowing re-oxidation from entering air. Emulsions of inexpensive, non-aqueous organic microdroplets dispersed in water provide earth wettablility equal to aqueous solutions and easy percolation into both the ground and mine waste. Subsequent breakdown of the O/W emulsion provides permanent retention of the organic phase, attached to earth particles, that secures lasting anaerobic conditions, precipitates metals as sulfides and prevents re-oxidation of these sulfides. This process and its optimization are described, including experiments with sand-filled columns representing a vertical section through solid waste. Results of organic and metal retention in solid waste are provided from analyses of acid mine water drainage before and after waste treatment.

Jan 1, 2006

By M. -L. Metsärinta, J. Nyberg, A. Roine

The Kokkola roasting plant uses more than 20 different zinc concentrates every year. During recent years there has been an increase in the variation in concentrate quality; in particular, the amount of fine-grained and low-grade concentrates has increased. Therefore, a great deal of development work has been carried out to improve the operational flexibility, online availability, production capacity and calcine quality of the roasting plant. This work consisted of a heat and material balance model of the roasting based on HSC Chemistry software, a new water admixture system for the concentrate feed, a new oxygen feed system for the process air line, improved cooling of the furnace and boiler and improved operational practices, dust removal and concentrate mixing. These new process control tools and other improvements, as well as some test results, will be described in this paper. The oxygen feed may be used to improve production capacity and to decrease the sulfide content of the calcine. The water feed may be used with fine concentrates to decrease both dust carry-over and the temperature in the top part of the furnace. Improved cooling of the furnace and boiler helps to increase production capacity.

Jan 1, 2000

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years&apos; expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan&apos;s new smelter

Jan 1, 1999

By C. Hecker, J. A. Garcia

To determine the kinetic reaction mechanism, electrochemical experimental techniques of stationary polarization, linear voltammetry and faradaic impedance were used. Gold electrodeposition experiments were realized using an electrolysis cell, provided· by a rotary disk of vitreous carbon and or' platinum counter electrode of platinum mesh and reference electrode. Using an automatic measurement system voltarnmograrns and Nyquist faradaic impedance spectra were obtained. In this paper, responses for different cases were analyzed through faradaic impedance criteria, considering several kinds of diagrams obtained. The importance diffusion influence of aurocyanide ions and adsorption as controlling steps previous charge transfer was verified. A model of proposed mechanism is discussed.

Jan 1, 1997