Search Documents

By B. J. Vorster

AngloGold South Africa region currently consists of 12 Gold Plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the .major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leachlcost optimisation. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in detennining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic? manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in. isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner's well known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the? original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimisation work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environmental; risk.

Jan 1, 1998

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By D. E. Larson

In cooperation with the National Institute of Environmental Health Science and the National Institute for Occupational Safety and Health the U.S. Bureau of Mines conducted grinding research on non-asbestiform tremolite. The goal of this effort was to prepare ground tremolite samples containing a considerable percentage of acicular grains with aspect ratios (approximately = 8um long with widths = 1 um) similar to those of asbestos particles suspected of causing cancer, Optical-and electron-microscopic examinations were used to monitor the size and shape of the grains in the ground products. Although customized milling techniques do have noticeable effects in producing acicular grains, the prismatic nature of fracturing in the non-asbestiform tremolites limited the number of acicular grains that could be purposely produced, and indicates that the likelihood of high concentrations of acicular particles occurring under normal mining and milling conditions is small.

Jan 1, 1991

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Y. Shigeno

The reactivity of a porous solid is a strong function of its pore structure (porosity, pore surface area and pore size distribution). It follows that reactivity could be altered by altering pore structure; one way to achieve this is by chemical vapor infiltration whereby a gaseous species is reacted in the porous solid to produce a solid. Experiments were carried out in which the pore structures of various carbons were modified by cracking methane within the pores; oxidation rates of the carbons were then measured for both infiltrated and original samples. For coke it was found that two indices of coke performance used in the steel industry (CRI and CSR) can be greatly improved following a small amount of infiltration. Infiltration/oxidation results are interpreted in terms of measured pore structure changes.

Jan 1, 1993

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By Cleusa Cristina Bueno Martha de Souza

Hydrometallurgical techniques for processing metals are becoming an efficient method for recovering metals. Although batteries' manufacturers have got rid of mercury content, some efforts have been made for recovering other metals enclosed in the battery formula. This paper discusses the bench scale experiments in the purification process of leached solutions from alkaline spent batteries. After leaching process using sulfuric acid as leachant, the solutions containing Fe, Cd, Pb, MIl, Zn and K were neutralized to precipitate iron hydroxide. In a second step, the purification experiments were carried out with excess of zinc dust to try to remove Cd while Mn and Zn still remain in the solution to be recovered in an electrolysis stage. The purification experiments procedures were conducted at different temperatures and times to find out properly conditions from the viewpoint of metals removal After filtration the solutions were submitted to chemical analysis to certify the metals content extracted.

Jan 1, 2001

By Jogre A. S Tenório

he aim of the present investigation was to investigate technological features of the Fe-NbC dissolution in liquid Fe-C alloys. Fe-NbC is a Ferro-niobium alloy with 7%C, has a particle size smaller than 150 pm and its micro constituents are polygonal niobium carbides and an iron matrix. The obtained dissolution time was less than one-minute and the yields were in the range of 80-90% at 1873 K. In the Fe-NbC dissolution process, the dissolution occurs at first, and as a consequence the niobium carbides become free to dissolve. These carbides will dissolve until the melt reaches a saturation point. The non-dissolved carbides remain trapped in the liquid or will form a dross. The addition yields decreases when the niobium concentration reaches this limit value, that depends on the carbon concentration. These define a saturation curve.

Jan 1, 1994

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By Finn Olesen, Melina Garcia, Mark William Kennedy

"Furnace resistance is a function of the complex interrelationship between many factors including: operating practice, slag conductivity, temperature, power intensity, and geometry (electrode shape, diameter, spacing, immersion, slag depth, etc.).Accurate prediction of resistance is critical for success of the overall furnace design. The sizing of electrodes, columns, bus-bars, and transformers are all impacted. Estimation of minimum and maximum resistance or maximum operational current, as well as the maximum operating voltage are of fundamental importance.Various mathematical tools have been developed to assist designers with the selection of furnace dimensions and the prediction of resistance. Elkem found the methods of Downing and Urban 1965 and Westly 1975, to be particularly useful.In the current paper, comparisons are drawn between data from spent aluminum pot lining (SPL) demonstration testing at Elkem Bjolvefossen and predictions based on these classical tools and 3D finite element modeling (FEM) with COMSOL.®"

Jan 1, 2012

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By Marcelo B. Mourão

The reduction of iron ores by solid carbon, when both are agglomerated together in the form of pellets, has important kinetic advantages. Although several studies have been performed on the subject, some points on the controlling mechanisms need clarification. There is a big scatter in the values of the apparent activation energy reported in the literature, and this may be due to factors like heat transfer, flow of gases in the reduction system, pellet size and composition. This work is concerned with the effect of several parameters on the reaction rate. The parameters studied were temperature (in the range 1173 K to 1423 K), carbon type (coke or charcoal), pellet size, gas flow rate, catalyst action of the produced metallic iron and added sodium carbonate. It has been shown that the values of the apparent activation energy can change according to the reduction conditions employed, and hence any modeling effort will have to take account of these parameters. EPD Congress 1994

Jan 1, 1994

By Albaharna O. T., Argyropoulos S. A.

"This paper describes the development and the implementation of process control in a variety of instruments used in metallurgical laboratories. These instruments are used for different research projects in extractive metallurgy. Hardware and software aspects for this implementation are described and analyzed. Extractive metallurgy applications where process control was .used are presented. IntroductionMicroprocessors are invading almost every area of our lives and are turning up in unexpected applications. A great deal of new equipment which is coming into the market have built- in microprocessor systems. Nevertheless, the area of upgrading existing processes has been slow to develop. There are a variety of reasons for this, and many of these are economic. One of the principal reasons, however, is the general reluctance on the part of many organizations to commit a strong effort to put this new technology into their existing processes.Microprocessor systems developed ""in lab"" are capable of not only measuring thermophysical events which are taking place in metallurgical furnaces, but simultaneously controlling these furnaces. In this paper software and hardware aspects in the implementation of microprocessor control for resistance and for induction furnaces are presented. In addition to this, metallurgical results are given from experiments where this furnace control was applied."

Jan 1, 1989

By Jay R. Hitchings

A technique that enables excellent color photograph production from black and white negatives of electron microprobe x-ray images is described in this paper. The photographs are made by superimposing one, two or three negatives of black and white x-ray images individually through assigned primary color filters directly onto color print paper. When used to examine metallurgical or geological microstructures, the resulting color photograph provides detailed, qualitative information about spatial arrangements, elemental associations and relative concentrations of at least three elements. The technique is simple and straightforward, requiring only standard darkroom equipment. The use of color to display or present complicated microprobe data also allows a non-technical reader or audience to better understand the data.

Jan 1, 1981

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

The influence of SiO2 on the reducibility of the CaO–Fe2O3–SiO2 system was fully examined in this study. The isothermal reduction kinetics of CF and CF8S (CaO/Fe2O3 = 1:1, wt% (SiO2) = 8) were investigated through thermogravimetric analysis at 1123, 1173, and 1223 K with 30% CO and 70% N2 gas mixtures. The reduction of the samples with 8% SiO2 was not only highly accelerated but also proceeded easily. Rate analysis revealed that CF and CF8S reduction occurs in two stages, the Fe3O4-to-FeO stage overlaps with the previous Fe2O3-to-Fe3O4 stage and tends to approach the following FeO-to-Fe stage with the addition of SiO2. The apparent activation energy values of CF and CF8S reduction are 46.89 and 8.71 kJ mol−1. Sharp analysis indicated that CF and CF8S reduction was expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction.

Mar 1, 2017

By Juan B. Cabezas

"The favorable characteristics and workability of plastics as a replacement of wood, lead, stainless steel, asphalt and other materials are described. Various types of plastic have proven to be the most favorable choice for handling a variety of acidic, alkaline and organic solutions, as well as pulps, chemical wastes, slurries or tailings for impoundments. The material origin of various plastics, methods of manufacturing and specifications applied to leaching solutions are discussed, including availability and costs. Examples of select plastics are considered for use as alternatives of other materials under severe environmental requirements.IntroductionHydrometallurgical processes applied to gold recovery, as well as other metals, require the use of strong solutions of alkaline, acidic or organic nature, and may also include a variety of materials with extraneous characteristics and complications for handling in storage.The technology of leaching has been in use for more than 100 years, but the applications of leaching processes in metallurgy have become more commonly used in the last 15 years. Suitable materials for the construction of containers, launders, piping, and various accessories, to be used in the handling of leach solutions or slurries, have become a serious problem. Various metals such as brass, lead, stainless steel, etc., and non metallics including wood, clays, glass, rubber, ooncrete, tars or miscellaneous compounds have been tried in the past with serious limitations in workability and resistance to wear and corrosion. For example, the use of metallic, wooden or glass piping systems would require extraordinary shop maintenance to keep such systems in operation"

Jan 1, 1997

By I. E. A. Aghachi

During static strain-aging of low carbon steel, when the material is pre-strained, the dislocation density increases. If totally or partially unloaded and aged for a prescribed time, interstitial solute atoms diffuse under the influence of the dislocation stress fields, thus tending to lock dislocations causing an increase in yield stress. If held for long periods at certain aging temperature, a decrease in yield stress (over-aging) is observed following the initial increase. This behaviour has been variously attributed to either recovery of cold worked dislocation structure and/or formation and coarsening of carbide precipitates. The present work demonstrates that, using a "process control" model for the competing processes of hardening and softening, dislocation recovery is responsible for over-aging of mild steel specimens under conditions tested during this investigation. Keywords: Strain-aging, Precipitation, Recovery

Jan 1, 2003