Search Documents

By Y. W. Miao

Along the south-west coast of Taiwan is about 550,000 metric tons of heavy sand deposit containing about 10 % black monazite. The Institute has developed a separation process to recover the individual rare earths and the developed process has been commercialized by a local private company. The decomposition of the local black monazite by sodium hydroxide through hydrothermal and fusion methods has been investigated. In the hydrothermal process 4.5 wt. % of aqueous alkali solution was used in an autoclave. In the fusion process, caustic soda (9.8% NaOH) was employed in am open cylindrical reactor. The same product of hydrous rare earth oxides were obtained and then dissolved by hydrochloric acid and the p-H adjusted in order to separate the thorium from the rare earths. After filtration, the filtrate contained rare earth chloride and the cake contained mainly the silica and thorium hydroxide. Both methods give a yield of 90 % with respect to the rare earths recovery. A detailed description of operation and comparison of the two methods are given.

Jan 1, 1989

By Daniel Gauthier, Patrick Sharrock, Cedric Verwilghen, Gilles Flamant, Ange Nzihou, Jocelyn Ramaroson

Clean processes are needed to dispose of many wastes. The incineration of 1 ton of municipal solid waste generates 6000 Nm3 of combustion gases contaminated with heavy metals and other pollutants. Gas scrubbing processes are required to clean incineration fumes in order not to transfer pollution to the atmosphere. We are investigating the use of Hydroxylapatite (Ca-HA) particles for use as sorbent for the removal of volatile heavy metals. We have carried out the synthesis of Ca-HA by two precipitation methods from solution and obtained solids with specific surface areas reaching more than 100 m2/g. Preliminary adsorption experiments were conducted in a horizontal furnace by mixing Ca-HA with 5% by weight of cadmium chloride in solid state. The mixture was heated to 600°C under air atmosphere during 6 hours. Chemical analysis of the solids confirmed that 85 % of the cadmium was retained in the solid phase. Such laboratory results showed that Ca-HA is capable of adsorbing cadmium chloride vapors, and pilot scale studies confirmed cadmium abatement in an industrial context.

Jan 1, 2008

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By Yang Tian-zu

The separation of precious metals from base metals containing in gold-antimony alloys by selective chlorination leaching under controlling potential was studied in this work. The effects of the consumption of hydrogen peroxide, the concentration of hydrochloric acid, the concentration of sulfuric acid, leaching temperature, leaching time and the liquid-solid ratio in hydrochloric acid system on the leaching efficiencies of the base metals have been investigated. The optimal leaching conditions of the gold-antimony alloys are as follows: hydrochloric acid concentration 4.0mol?L-1, sulfuric acid concentration 1.2mol?L-1, liquid-solid ratio L:S=7.5:1, the leaching temperature 80 0C, leaching time 2h, and the oxidation potential of the leaching system 400±20mV( vs SCE).The leaching efficiencies of copper, nickel and antimony are more than 99% and the gold leaching efficiency is about 0.042% under the above leaching conditions. The base metals containing in the gold-antimony alloy are separated from the precious metals thoroughly.

Jan 1, 2006

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Jicheng Liu, Manman Lu, Tao Jiang

Blast furnace slag (BFS), one kind of typical solid waste in the steel industry, was used as structural materials to synthesize NaNO3/BFS composite phase change materials (C-PCMs) by mixing and sintering method. NaNO3 in the composites functioned as phase change materials (PCMs) and BFS as structural skeleton to maintain a stable external form. In this study, the prepared C-PCMs could remain in the solid state without salt leakage even if operating temperature exceeded the melting temperature of NaNO3. The composition and structure of BFS and the prepared composites were characterized by XRD, FTIR, SEM and TG-DSC analyses. The results showed that NaNO3 was well incorporated in the pores of BFS. The melting temperature and latent heat of the final composites were 300.5 °C and 65.53 J/g, respectively. The product also had good thermal storage performance and durability even after 100 thermal cycles. The energy density of the product was calculated as high as 468.03 J/g for an temperature range of 50–400 °C.

Mar 1, 2018

By Yan Yuan

Stable Nitroxyl polymers, such as poly (2,2,6,6-tetramenthyl-1-piperidinyloxy-4-yl methacrylate) (PTMA), are known to be effective as cathode active materials for lithium rechargeable betteries.The nitroxide radicals displayed a reversible and very rapid redox performances.We present a new synthesized method to get PTMA powder, then a doctor-blading method was used to prepare the PTMA composite electrodes, enabling successful production of homogeneous electrodes. It was characterized through FT-IR and SEM methods.The organic radical battery consists of lithium metal anode and PTMA cathode with an active material content of 65wt%.The best performance is achieved with a thin cathode that shows nearly 100% utilization of the active material (111mAh/g) at 0.1C.Through the electrochemical tests, it was found that there was a stable plateau at 3.5V while discharging. Besides, the cycling stability and rate capability were measured in detail. Although they showed a certain quantity of irreversible capacity on the first cycle, the capacity stabilized after the second cycle.

Jan 1, 2009

By Zhigang Zak Fang, Michael L. Free, Jaehun Cho, Syamantak Roy, Amarchand Sathyapalan

Leaching characteristics of impurity removal from the Upgraded Titania Slag (UGS) using hydrochloric and boric acids has been investigated. Specifically, this study has focused on removal of iron oxides from the UGS that has been reduced by hydrogen gas and magnesium at 750oC for 5 hours. Reduced UGS is mainly composed of titanium hydride and impurities like iron oxides, silicon oxide, aluminum oxide, and magnesium oxide. The concentration of hydrochloric and boric acids and the leaching temperature have been chosen as the prime variables to identify the optimum conditions and leaching characteristics for removal of iron oxides. It was observed that under the constraint that 1 wt % of titanium hydride loss is the maximum amount tolerable, 0.1M HCl with 1M boric acid and 90oC are the most effective parameters for iron removal from the reduced UGS. Also, the overall rate of reaction seems to follow interfacial reaction controlled kinetics. The calculated activation energy of the reaction is 73.90kJ/mol.

Jan 1, 2016

By M. I. Kalashnikova

Gipronickel Institute has developed the technology of treatment of difficult to concentrate sulphide Pb-Zn concentrates (Zn-19,9%, Pb-8,4%, Cu-0,34%, Fe-8,8%, Ba-6,8%, S-18,7%, Ag-106 g/tonne). The technology consists of pressure leaching, impurity removal from leaching solution, electrowinning and Pb-Ag containing cake treatment. Despite low zinc content in initial concen-trate the technology allows production of solution which is suitable, after standard procedure of impurity removal, for electrowinning with production of zinc grade SHG. Comparing to the standard technologies the flowsheet developed provides the lesser expenses per zinc unit because of decreasing of liquid to solid ratio at pressure leaching stage. The initial concentrate is characterized along with low content of principal metals by high con-tent of barite, which makes flotation of pressure leaching residue more difficult. That is why in this case the hydrometallurgical treatment was chosen. At optimal parameters of chloride leach-ing found during laboratory experiments the principal components extraction was 99.5% for Pb and up to 92% for Ag.

Jan 1, 2006

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By Tsembel Darjaa, Toru H. Okabe, Yoshiaki Umetsu

"With the purpose of extracting molybdenum and rhenium from molybdenum sulfide concentrate; .electrolysis of slurry, solvent extraction and ·precipitation operations were carried out. The slurry of the concentrate in 10 mass% NaCl aqueous solution was continuously circulated into a vertical type 10 stack bipolar electrolytic cell consisted of carbon electrode disks, and, the concentrate was dissolved by electrochemically generated oxidizers at 313 K. The current efficiency for molybdenum dissolution was 73 % after 10 hours electrolysis, and the leach solution was found to contain 0.2 mol/l of molybdenum and 4x10-5 mol/l rhenium. This result shows the dissolution is more than 8 times faster than that obtained using a single cell. The leach solution from electro-oxidation was then subjected to a solvent extraction for rhenium which is then recovered as sulfides. After rhenium separation, molybdenum was precipitated by pH adjustment, and solid MoO3 (H2O)x crystals, free of sulfate, were obtained from the leach solution containing large amount of so42-.IntroductionIn the past, electro-oxidation using a bipolar cell was applied for leaching molybdenite concentrate and ores at U. S. Bureau of Mines [1-3] and also at Bhabha Atomic Research Center [4]. In· these previous studies, Moebious type bipolar cells, in which electrode plates were vertically inserted into the free surface of the electrolyte, were employed and its effectiveness was demonstrated.Recently, the present authors studied on leaching of Mongolian molybdenite concentrate, and the effectiveness of leaching of the concentrate by electro-oxidation in alkaline and acidic NaCl solutions was demonstrated [5]. The leaching reaction during the process can be explained by the 18 electron transfer reaction of molybdenite (MoS2) with the oxidizers produced in-situ by electrolysis of NaCl aqueous solution. Further investigation was made with respect to various process parameters for electrooxidation such as pH, pulp density and temperature of the slurry, and the dissolution behavior of minor elements such as iron, copper, and rhenium [6]. Solubilities of molybdenum in the leach solution at, various temperatures and pH .was · studied, and feasibility of molybdenum recovery by hydrolysis of molybdenum species was demonstrated. By adjusting the pH of the leach solution, molybdenum oxides or hydroxides free from sulfate were successfully obtained from the solution containing large amount of sulfate ion. Rhenium present in the concentrate at a level of several tens of mass ppm was found to dissolve into the leach solution, and co-precipitate with the molybdenum compounds. Rhenium in the leach solutions, therefore, has to be recovered before precipitation of molybdenum, otherwise it is lost in the precipitate."

Jan 1, 2000