Search Documents

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

Cuspidine (3CaO?2SiO2?CaF2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel. The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiOrCaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been determined by an electromotive force method using CaF2 as solid electrolyte and a transpiration method as follows: The chemical potential diagram and constituent activities for the CaO-Si02-CaF2 system have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By S. Castro, P. Alfaro, C. Moctezuma

IMMSA operates a conventional roasting-leaching-purification-electrolysis plant for the production of zinc from concentrates in San Luis Potosi, Mexico. The leaching circuit was designed to take into consideration a feed mixture to the roaster with a maximum iron content of 7%. Since the start-up of the plant in 1982, the zinc recovery increased to 94.5%. However, an increase in the iron content in 1997 caused an important decrease in the global zinc recovery. Two new steps were added to the leaching circuit and modifications were made to the other steps in order to increase zinc extraction. Two new automated press filters were installed to replace the original vacuum drum filters and to minimize soluble zinc losses. Additionally, the residue treatment steps in purification were modified and a calcium removal circuit is just starting operation. These actions, besides improving the operations, have as the main objective to increase the global zinc recovery to levels above 94.5%.

Jan 1, 2000

By T. J. White

A synthetic Mineral Immobilization Technology (SMITE) has been developed for stabilizing municipal and hazardous waste incinerator ash. Tailored additives are introduced to the ash in a' first stage that pre-stabilizes all the toxic metal components in non-volatile forms. and in a second pyrometallurgical stage, these are converted to insoluble mineral analogues. It has been found that a combination of apatitie. spinal, anhydrite and monazite can immobilize all the ash components at high waste loading and high density. Typically the stabilized products contain in excess of 50 wt% ash and have densities of 2.5- 3.0 g.cc-1. Toxicity Characteristic Leach Procedure (TCLP) testing has demonstrated that the products well satisfy regulatory requirements. The cost of production and disposal of SMITE waste forms in 2-5 less expensive than. convential methods of solidification/stabilization. This paper will describe the principles of SMITE design for ash stabilization, outline the fabrication procedure, and present comprehensive microstructural and chemical data to validate waste form performance.

Jan 1, 1996

By F. Patisson

During exothermic gas-solid reactions, heat generation makes temperature rise and modifies the rate of the various mass transfer processes, namely the chemical reaction itself, the pore diffusion and the external transfer. We have investigated this thermal effect during the oxidation of zinc sulfide porous pellets in a thermo balance furnace, between 550 and 900°C-and under O2-N2 atmosphere. The results have been' analyzed by using, firstly, the law of additive reaction times derived from the isothermal Grainy Pellet Model, and, secondly, a new numerical model taking into account non-isothermal conditions. Both the models can satisfactorily simulate conversion versus time, but the numerical model also depicts the temperature evolution within the pellet. Finally it is shown that owing to the heat generation the zinc sulfide oxidation takes place under diffusion control (3/4 internal, 114 external) in all the cases studied. During the course of reaction, the. pellet undergoes strong temperature variations, with thermal gradients confined to a shell oxide layer.

Jan 1, 1996

By J. F. Leroux

The Gaspé smelter at Murdochville, Quebec, Canada introduced concentrate injection into elongated Peirce-Smith converters sized 1.96m x 12.5m (13 ft. by 41 ft.) in 1996, and commissioned a large, converter-like bath smelting vessel in April 1998. The new vessel, which is sized 4.27m x 16.1 5m (14ft. by 53ft.) has several interesting features designed to effectively utilize bath smelting technology for the requirements of the Gaspé smelter. For example, the vessel can operate on concentrate injection at upwards of 60-80 tph rate on an instantaneous basis, can operate as a large Peirce-Smith converter, while it is also fitted with matte and slag tapholes much akin to Noranda Process reactor, and includes a novel cold charge addition system. The new technology will eventually allow the capacity of the plant to increase from about 300,000 tonnes of concentrate per year to over 350,000 tonnes of concentrate per year while improving sulfur capture.

Jan 1, 1999

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By Dongxing Wang, Zhang Ting-an, Xiaolong Li, Yan Liu

Recent years, bottom blown oxygen copper smelting process has been widely used in China. Besides many advantages such as autothermal operation, this technology is still in developing stage. This topic aims at promoting the dispersion of materials charged into the bottom blown smelting furnace used in the process. Based on the similarity theory, a 1/5 scaled physical model of smelting furnace was constructed. Polypropene particles were used as charged materials. High-speed camera was used to record the phenomenon of the particles dispersion under different gas-flow rates, nozzle diameters and installation angles of nozzles. Image processing software was used for obtaining the particles concentration under different conditions. Results show that when the gas flow rate increases, charged materials disperse better. With the same gas flow, the increasing of nozzle diameter promotes the dispersion effect of materials. The effects of installation angles are opposite for nozzles with diameter of 2.50 and 5.92 mm.

Mar 1, 2017

By J. Brent Hiskey, Rebecca Grace Copp

The solvent extraction of yttrium and neodymium from copper pregnant leach solutions (PLS) using Primene JM-T, a primary aliphatic amine, has been studied. Effect of contact time, pH, sulfate concentration, and extractant concentration were investigated using synthetic and actual PLS systems. Standard experimental conditions were 5 minute contact time, pH ~2.5, and 10 % v/v Primene JM-T concentration. Distribution isotherms were constructed for the pure systems and for actual copper leach solutions. Synthetic solutions contained 100 ppm Y and ~75 ppm Nd. Samples of PLS contained 2 - 10 ppm Nd and 14 - 30 ppm Y. Results showed that complete extraction of both yttrium and neodymium occurred within five minutes and at pH values greater than 1. It was also found that sulfate concentration does not inhibit extraction at any concentration. Additionally, the distribution isotherms created show that extraction for these metals can operationally take place in one stage.

Jan 1, 2016

By Mikhail Mikhaylenko

Natural and technogenic sources of rare earth elements (REE) and other rare and scattered metals are remarkable for their chemical diversity. The pregnant solutions going to processing for the valuable metals have very complex compositions. Both targeted elements and competing impurities are present in the solutions in different chemical forms. Thus processing of such materials demands application of different technological tools addressing numerous specific tasks on the way to the final product. Screening work was undertaken to identify the best resins among developmental and commercial products addressing typical cases in the hydrometallurgy of scandium and REE. The cases outline typical sources of scandium and REE, such as streams of TiO2 production, extracted phosphoric acid, barren uranium solutions and others. Specially designed ion exchange resins can be effective tools.

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

"Mixing phenomena in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor was studie9-using three different configurations of straight circular nozzles fitted axially at the bottom of the vessel. The mixing time has been determined by pH measurements at various gas flow rates, bath heights and nozzle orientations in the presence and in the absence of a second phase.Experimental results reveal that the mixing time decreases with increasing gas flow rate. For a given gas flow rate the mixing time increases non-linearly with increasing bath height. Off-center configuration gives slightly lower mixing times as compared to center configuration. It is found that the contribution of buoyancy to the total stirring energy density is very small, but its contribution increases with increasing bath height. In the presence of an upper oil layer, the mixing time increases significantly for all configurations.IntroductionIn high temperature metallurgical melts mixing is carried out by injection of a gas either from top or bottom of the vessel in order to accelerate the rates of chemical reactions and to promote bath homogenization. When a gas is injected into a liquid through a submerged lance, porous plug or nozzle, the gas, rising as a two phase plume to the surface, imparts momentum to the surrounding liquid and causes gross circulation in the bath which promotes mixing."

Jan 1, 1997

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

By Vladimir Mindin

Simulation of complex equilibria is usually done in the P-T-X coordinates, where "Xu is the amount of individual chemical components in the system. This approach is not productive in some very important cases: (i) investigation of "open" systems, (ii) determination of coordinates (trajectories) of mono-variant points, among others. To solve these and some other problems, we use the idea of chemical potentials of elements (CPE) of the system. A system of different coordinates axes (CPE-axes ) leads to a new strategy of simulation, observing the results of the simulation, and to efficient technology of compressing and storage the data of the simulation.

Jan 1, 1994

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

By M. Sahoo

The development of new alloys containing bismuth and selenium for potable water supplies are reviewed. The new alloys are replacements for the leaded red- and semi-red brasses by the low-lead alloys, SeBiLOYS I and II, for sand casting, and SeBiLOY III replaces the lead containing yellow brass, C85800, for permanent mold casting. As the new alloys use bismuth and selenium, the supply and demand of these elements are discussed. The key casting characteristics discussed are: tendency to dross formation, freezing range (liquidus and solidus temperatures), fluidity, resistance to hot tearing, microstructures, mechanical properties, machinability, grain refinement and corrosion behaviour.

Jan 1, 1999

By Huai-ying Ma, Jun-hua Zhao, Xia Zhao, Si-bin Zhang, Wen Pan, Zhi-xing Zhao

Ignition is the start point of the sintering circuit, which plays an important role during the whole sintering process. The gas consumption accounts for 80% energy cost in the sintering ignition process. Therefore, gas flow reduction is of great significance to energy conservation in the sintering ignition process. In current study, the concept of comprehensive ignition intensity (CII) was introduced to determine the ignition effect. The experimental results indicate that the value of CII increases with higher air-fuel ratio at gas flow of 550 and 600 Nm3/h. From another point of view, given constant CII value, lower gas flow can be achieved with higher air-fuel ratio. Based on the comprehensive ignition intensity, the ignition parameters were optimized and the gas flow was subsequently reduced. By increasing the air-fuel from 5.5 to 6.6, the gas flow is reduced from 450 Nm3/h (8.1 GJ/h) to around 350 Nm3/h (6.3 GJ/h).

Mar 1, 2018

By Baozhong Ma, Chengyan Wang, Yongqiang Chen, Peng Xing

This paper introduces an oxygen-enriched flash smelting (OFS) process for lead smelting. Compared with the bath smelting, OFS has many advantages, including wide adaptability, high yield, low energy consumption, little uncontrolled emission, and considerable metals recoveries. Test results showed that increasing CaO could effectively reduce lead content in the slag, and the appropriate mass ratios of FeO-to-SiO2 and CaO-to-SiO2 were 1.15 and 0.6, respectively. The testing and commissioning indicated when OFS was used to treat material containing 30% of lead, the residual lead in slag could decrease to 4–10%. Furthermore, after zinc volatilization using an ore-smelting electric furnace, contents of lead, zinc, silver, gold and copper in the final slag were below 2%, 2%, 6 g/L, 0.1 g/L and 1%, respectively. The total recoveries of lead, zinc, silver, gold, copper and sulfur were above 98, 90, 99.5, 99.5, 85 and 98%, respectively.

Mar 1, 2018