Search Documents

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By G. Diáz

A basic technology coping with a wide range of secondary zinc sources has been developed. The process combines an electrowinning stage, a solvent-extraction unit and a leaching procedure. The acidity generated in zinc electrowinning, transferred by the organic solvent to the aqueous raffinate, is reused to leach the zinc secondary materials. The basic process recovering zinc is described in detail. The route recovering other valuable metals such as copper, cadmium and lead associated with zinc is also described. This non-ferrous metals recovery route is advisable for either ecological and/or economical reasons. Main results of an experimental program aiming at the demonstration of the suitability of the process for several feed materials are summarized. Waelz oxides, galvanizing ashes and EAFD coming from different sources were tested in laboratory and continuous pilot plant campaigns. High zinc recovery, low reagents and utilities consumption, and effluents meeting environmental regulation were confirmed. The paper also includes the main results of a feasibility study of an industrial "base case". A mixed raw material and Spanish EAFD and 20,000 ta of zinc ingots production were chosen. The SGH zinc recovery from secondary raw material by means of the clean, safe and profitable Modified Zincex Process has been demonstrated. This reliable technology is ready for industrial application.

Jan 1, 1995

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Tianjiao Luo

The electroless copper plating process for continuous carbon fiber using CuSO4?5H2O as the main salt and formaldehyde as reducing agent was experimentally studied, including the effects of pH values and concentration of chelating agents, stabilizing agents and reducing agent on the electroless plating process. The surface morphology and the composition of coating were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), and deposited the coating thickness was measured by way of dissolution. The results indicated that the pretreatment of carbon fiber before plating was so important. This pretreatment could prevent the formation of the black cores, furthermore, it could form many active absorption cores with Ag as the center on the carbon fiber surface. Used the optimized parameters in this process, which led to a stable solution for plating, a homogeneous copper coating was conducted with the carbon fiber plated with favorable mechanical performance and high adhesion strength.

Jan 1, 2006

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By M. A. Barakat

"Adsorption of heavy metal ions specifically, Cu(II), Zn(II), Mn(II), and Cr(VI) from aqueous solution on synthetic 4A Zeolite was evaluated. The 4A zeolite was synthesized previously by dehydroxylation of low grade Kalabsha Kaolin at 800 °C, and reacted hydrothermally with 2-4 M NaOH solution at 100 °C for 2h. The adsorption capacity of the metal ions were found to be strongly dependent on pH and initial metal ion concentration. At the optimium conditions the adsorption capacity decreased in the order Cu(II) > Zn(II) > Mn(II) > Cr(VI) ions. Almost complete adsorption was achieved for both of Cu(II) and Zn(II) ions at pH > 6, while the adsorption capacity for both Mn(II) and Cr(VI) was 96, and 55.3 % at pH 11 and pH 3, respectively. The results also showed that the grain size of the 4A zeolite has a little effect on the adsorption capacity. The experimental data was compared with two adsorption isotherms, Langmuir and Freundlich isotheroms. The results showed a good agreement of the Langmuir plots with the experimental data.1. IntroductionSeveral industrial wastewater streams may contain heavy metals such as Cr, Cu, Pb, Zn, Co, Ni, Mn, etc. including the waste liquids generated by metal finishing or the mineral processing industries. Heavy metals are considered hazardous pollutants due to their toxicity, even at low concentration, and nonbiodegradability. Increasing level of heavy metals in natural water bodies poses a serious threat to all living species including humans. It is, therefore, essential to reduce the heavy metal concentration in effluents/wastewater before it is discharged into the water bodies [1]."

Jan 1, 2008

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Li Chen

A new process, i.e. Ball milling--Neural leaching--Oxidation calcinations--Chloridizing distillation--Hydrolysis, was designed to recover germanium from the vacuum furnace slag produced in Shaoguan smelter. The suitable process and operational parameters were determined for the practical production.

Jan 1, 2005

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Qing Bo

In this study, the cobalt oxide precursor was prepared in open-style reactor in the condition of high reactant concentration, and then the precursor was decomposed to obtain the cobalt oxides (Co3O4). The effects of some factors on the cobalt precipitation, the particle size and size distribution, and the micro-morphology were addressed. The factors studied include cobalt concentration, initial pH of solution, temperature and time for the reaction, the charge amount of urea, and the temperature for decomposition. It is determined that the precursor particle is in the chemical composition of Co2(OH)3Cl with fine crystalline. By calcinations under proper conditions, the mono-dispersed cobalt oxide particles were prepared with fine crystalline, about 2 µ m in particle size and regular shape in morphology.

Jan 1, 2006

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By Taegong Ryu

A thermal plasma process was used to synthesize nanosized tungsten carbide -cobalt composite powder, in which ammonium paratungstate and cobalt oxide were reacted with a gas mixture containing CH4, H2 and Ar. The reduction and carburization of vaporized precursors produced nanosized tungsten carbide (WC1-x) - cobalt composite powder, which sometimes contained small amounts of W2C and/or W phase. The effects of gas composition, plasma torch power, and the flow rate of plasma gas on the product composition and grain size were investigated. The grain size of synthesized tungsten carbide powder was less than 20 nm. The synthesized composite powders were also subjected to a hydrogen heat treatment to fully carburize WC1-x, W2C, and W phases to the WC phase as well as to remove excess carbon in the product. Finally nanosized WC-Co composite powder of grain size less than 50 nm was obtained.

Jan 1, 2009

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005