Search Documents

By Miguel Barron

Recently, a new lance design for BOF steelmaking has been proposed in the literature. This lance, in addition to six peripheral inclined supersonic nozzles, contains a vertical centered nozzle whose oxygen flow is independent from the main oxygen supply. The above authors affirm that their lance maximizes the droplet generation without causing spitting. In this work, the performance of a lance with four peripheral nozzles and one vertical centered nozzle is numerically modeled by means of Computational Fluid Dynamics software. Transient two dimensional computer simulations were carried out considering two phases, namely molten steel and gaseous oxygen. Numerical results confirm that bath agitation and droplet generation are enhanced as a result of the vertical centered nozzle, however a proper performance of this lance, related to a conventional one, strongly depends on the Mach number of the oxygen jets and the lance height.

Jan 1, 2008

By Huimin Lu, Zhijiang Gao

Reduction reaction can happen among Al, V2O5 and TiO2 powders. Al can deoxidize metal V and Ti from the metal oxides. The electric igniter can be used to trigger the reduction. The reaction between Al and V2O5 is very intense and release large amounts of heat, but the heat which is needed to initiate the reaction between Al and TiO2 is not enough. These two reactions have been initiated first and V-Al and Ti-Al alloys can be obtained with a higher metal recovery percent. Through adjusting the ratio of Al, V2O5 and TiO2 powders, the system which combines these two reactions can ensured enough heat to react. KClO3 is added to the system, as the ignition agent, in order to make the reaction much complete. Finally, Ti-Al-V alloys can be obtained and need remelt to adjust the constituents.

Jan 1, 2016

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By Allan J. MacRae

A copper alloy to be used for coils in cast copper cooling blocks has been identified and samples prepared for metallurgical examination and destructive testing to compare with cast cooling blocks manufactured from copper and nickel-copper alloy pipes. The copper alloy allows for the formation of a metallurgical bond between the pipe and the cast copper during the casting process, which does not normally occur with pure copper or nickel-copper alloy pipes. The alloy's coefficient of thermal expansion is also much closer to that of pure copper compared with nickel-copper alloys, so there is less strain induced at the pipe-cast copper interface due to differential thermal expansion. It is expected that this new pipe coil alloy and associated casting techniques will allow for the production of cast copper cooling blocks that have greatly enhanced service life in high heat load applications compared to existing technologies.

Jan 1, 2002

By Cao rong-jiang, Tang Xin-he

"In ordinary manufacture process of tungsten powder, a preferable intermediate product used is ammonium paratungstate (APT). The particle size of tungten powder made from it through W2OO58 is larger than 1. 0 um. In order to obtain ultrafine tungsten powder with narrow size distribution, a new type of tungstate, hydraziniull tungstate, was studied. Its formula is 5(N2H5)2O·12 WO.s , with tetragonal crystal structure of a=5.821 , c=18. 468. Three methods for preparing hydrazinium tungstate (ART) were set up and ART can be produced by current industrial APT process with little modification of operation and without any change of equipment.Under certain PH and operation condition of the solution from which ART was produced, an autoreduction of tungsten occured, which produced a lower valency tungstate with blue color when ART was heated at different temperatures, in N atmosphere, tungsten bronze, tetragonal W0290 and W02.7E could be obtained respectively. They all have the superiorities, in the production of tungsten powder, of superfine size and narrow size distribution [average size of 0.5um or even smaller.The rate of autoreduction of ART is very fast at elevated temperature. The reduction reaction, which gaves tetragonal WO290, could be handled smoothly without explosion. To research their behaviors at autoreduction temperatures and the products of autoreduction will be new advances of tungsten chemistry and may also serve tungsten industry with new processes and materials."

Jan 1, 1988

By Seung-Chul Lee

Transparent conducting tin(1V) oxide thin films have been studies and developed for the electrode materials of solar cell substrate. Fabrication of tin oxide thin films by sol-gel method is process development of lower cost photovoltaic solar cell system. The research is focused on the establishment of process condition and development of precursor. The precursor solution was made of tin isopropoxide dissolved in isopropyl alcohol. The hydrolysis rate was controlled by addition of triethanolamine. Dip and spin coating technique were applied to coat tin oxide on borosilicate glass. The resistivity of the thin film was lower than 0.18-cm and the transmittance is higher than 90% in a visible range.

Jan 1, 1999

By Wei Han, Zhenwei Liu, Jianhong Yang, Qingwei Qin, Tiejun Chen, Zili Huang

The preparation of industrial ammonium molybdate from molybdenum concentrate was conducted according to the process of roasting—leaching—purification—precipitation—crystallization. The optimum technological conditions were determined: the roasting temperature was 680 degrees C, the roasting time was 2.5 h; in the leaching process the alkali excess coefficient was 1.2, the reaction temperature was 80 degrees C, the liquid-solid ratio was 3:1, the leaching time was 3 h; the amount of (NH4)2S added into the solution was 1.1 times of the theoretical amount, the temperature was 80-85 degrees C, and the terminal pH was 8.5-9 in the purification process; the density of the solution was 1.4-1.6 g/mL, the pH was 1.5-2 in the precipitation process; temperature of dissolution was controlled at 80-90 degrees C. The recovery of the preparation of ammonium molybdate can reach 85.18%.

Mar 1, 2017

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By Ana P. Paiva, Marc F. Comella, Sandra S. Reis, Joao N. Reis, M. Soledade Santos

"In this work, the influence of the malonamide structure, acidity of the aqueous phase and diluent on the equilibrium interfacial tension (IT) of N,N'-dimethyl-N,N'-diphenylmalonamide (DMDPHMA) and N,N'-dimethyl-N,N'-dicyclohexylmalonamide (DMDCHMA) in 1,2- dichloroethane (1,2-DCE), and DMDCHMA in toluene, with aqueous HCl, were investigated. IT isotherms were determined using the Du N ouy ring method. Densities of the organic phases were determined, and used to screen solute-diluent interactions. Formation of third phases was never observed; furthermore, ITs increase with the phase separation period, constant values being obtained for separation periods larger than 1000 seconds. Each malonamide interfacial efficiency at the oil/water interface is interpreted in terms of malonamide basicity, diluent polarity and malonamide - hydrochloric acid- diluent interfacial interactions.IntroductionFor several years now, N,N'-tetrasubstituted malonamide derivatives have been extensively investigated as liquid-liquid extraction agents since they were first proposed as the organic components of the DIAMEX process, with the aim of advantageously replacing tributylphosphate in PUREX [1]. Therefore, a significant part of research studies with malonamides appearing in the literature deal with the extraction of major and minor actinides in real or simulated spent nuclear fuels in nitric acid solutions [2]. Under typical experimental process conditions, the tendency shown by some N,N'-tetrasubstituted malonamide derivatives to aggregate in the organic phase, leading in a few cases to the formation of undesirable third phases, has been remarked and consequently thoroughly investigated [3, 4]. The increasing use of chloride streams as hydrometallurgical aqueous feeds is becoming a reality, and this fact is obviously deeply founded on an extensive research carried out to recover value-adding metals from these media. Following this trend, a number of N,N'-tetrasubstituted malonamides have already been screened for the recovery of iron(III) [5, 6] and platinum-group metals [7] from hydrochloric acid solutions. The results obtained are quite promising either in terms of total metal ion recoveries or selectivity patterns achieved. The formation of a third phase when iron(III) was extracted by the tested N,N'-tetrasubstituted malonamide derivatives has never been observed under the adopted experimental conditions, and the extraction data collected would need to be reinterpreted accordingly if any aggregation phenomena involving the considered extraction systems were to take place."

Jan 1, 2011

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinler should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified, In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By Tiruttani Munikamal, Suresh Sundarraj

"A numerical model of the induction hardening process of steel cranks has been developed and the predicted results of temperature and phase distribution during this solid state phase transformation process are verified with experimental data from the literature. This heat treatment process involves heating the crank to the austenitic temperature range followed by rapid quenching in water to harden the surface of the crank. The model has been developed using ABAQUS, commercial FEA software. The formation of martensite, pearlite, and retained austenite phases are modeled and implemented through a user defined function in ABAQUS. A sensitivity study on the various process parameters affecting the amount of phase distribution has been carried out.IntroductionThe type of surface and sub-surface microstructure as well as the residual stresses that are present in a component after manufacturing, significantly affects it fatigue performance. The wear resistance of the automotive components such as crankshaft, gears, camshaft and bearings depends on the surface hardness. In order to achieve the surface hardness, these steel components are subjected to a type of quench hardening heat treatment process. There are several heat treatment processes available for the industrial application to improve the mechanical properties of the final part. Case hardening using induction heating is one of the widely used industrial techniques for improving the surface microstructure of a steel component. It consists of two stages i.e. induction heating cycle, followed by quenching in a fluid medium (usually water or oil)"

Jan 1, 2012

By J. L. Hill, M. A. R. Sharif, J. Lin

"A numerical algorithm has been developed to simulate the movement, breakup, and entrapment of the oxide film inclusions encountered during the mold-filling processes of aluminum castings. The flowfield is solved using the well-known Marker and Cell (MAC) method by a time marching process. The Volume of Fluid (VOF) method is used to track the free surface boundaries. A kinematic approach is employed to track the movement and breakup of the oxide films on the free surface or in the bulk liquid metal. The computer program based on the proposed algorithm is able to model the flow behavior and oxide film movement, breakup, and entrapment in mold cavities for aluminum castings.IntroductionMetallographic and fractographic studies of the aluminum castings show tangled networks of oxide films in the castings. These oxide films can form in the furnaces or during the mold filling processes. Green and Campbell [I] concluded that the oxide film defects dominate the strength of aluminum castings. The main cause of oxide film entrapment into the bulk molten metal during the casting processes is the surface turbulence. In film-forming alloys, if the surface breaks, due to a drop, a fountain, or a breaking wave, then the surface film is folded over and incorporated into the bulk liquid. The incorporation of surface films leads to cracks in the casting and other defects that are nucleated by the presence of the folded films, such as porosity and hot tears. Campbell [2] estimated that up to 80% of scrap in light-alloy casting is the result of surface turbulence."

Jan 1, 1999

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

Bath smelting options for recovering valuable metals from jarositic residues containing 22-28% lead and 16-30% sulphur obtained from pressure leaching zinc-lead-copper bulk concentrates were investigated using thermochemical computations and crucible-scale experiments. Direct fuming of lead and zinc from a slaglmatte bath at 1250-300°C was demonstrated successfully. Up to 93% of the lead was recovered in the fume and steady-state recoveries of zinc were predicted in the range 82-95% under these conditions. The energy required for the fuming reactions was supplied by partial combustion of the fuel, added as char, with air. An important feature of the process is that the recoveries to the fume are not significantly affected by changing: the fuel:air ratio over a wide range. Thermodynamic computations, confirmed by experimental results also showed that the presence of a matte phase is not essential for high recovery of lead and zinc to the fume. Operating conditions which produced a matte ensured that about 70% of the silver and 80-90% of the copper were recovered into that phase. Approximately 98% of the arsenic in the residue was fumed. In the absence of matte the slags contained high arsenic levels (260-330 ppm) but low arsenic (20-60 ppm) levels were achieved when matte was produced.

Jan 1, 1994