Search Documents

By Stephen Tadolini

Reduction in the time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. While this concept is not without controversy and risk, the rewards can result in substantial reductions in longwall face move/set-up times and provide safer working conditions. Both of these factors can reduce mining costs and enhance profitability in a competitive market. This project was even more complex because the longwall system operates under a weak roof condition. To examine the feasibility of this concept, a 16-ft wide by 170-ft long experimental pre-driven recovery room was designed using analytical, empirical and 3-dimensional finite element modeling techniques. Based on the projected loading conditions, immediate and main roof geological and strength characteristics, a variety of roof bolt types were selected and installed in the recovery room and adjacent chutes. To supplement the intrinsic supports, high-capacity roof-to¬floor cuttable cribs were strategically placed to reduce the potential of a weighting failure before the longwall shields safely entered the room. To evaluate the behavior and final support performance, the recovery room and chutes were instrumented to monitor the physical response during various loading phases. Additionally, the cuttable cribs were instrumented to evaluate the loading and stiffness characteristics during the extraction process. This paper describes the successful design process, support methodology, monitoring results, final observations and recommendations.

Jan 1, 2002

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Nikolaos Polysos

Besides considering the given geomechanical conditions, the geological/geotechnical logging of drill cores and heading faces during the driving of parallel entries and the resulting rock classification form the basis of the assessment of the proneness to caving of the roof strata in the actual mining phase. Both types of separation planes, parallel to the stratification as well as intersecting the bedding, will be defined and assessed within the immediate roof strata depending on the lithological structure. These data may hold the potential to plan the winning and design its operational organization in a way that - to a major extent - future damage of the workings by increased caving or cavities can be predicted in advance. Following the general description of the separation plane structure, the combined influence of the petrographic and structural geological roof properties on the operating cycle of the planned working face will be presented and illustrated.

Jan 1, 2003

By Z. T. Bieniawski

This paper presents the results of a survey of room and pillar dimensions and design practice in U.S. coal mines aimed at improving the design procedures in room and pillar mining. A review is given of the current pillar strength formulas and suggestions are made for better utilization of research results in engineering practice.

Jan 1, 1981

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Yi Luo

The responses of a section of railroad to ground subsidence process was monitored as it was undermined by a longwall panel. The subsidence data collected and the observations made through this monitoring program could help us understand betteer the ground subsidence process and its impact on linear structures such as railroads. The data analysis techniques used and the assessment methods presented could be useful to researchers practitioners in the field of mining subsidence.

Jan 1, 1994

By James G. Schotsch

Unmapped abandoned mines are hazards for under¬ground mines, surface mines and surface structures. The Radio Imaging Method (RIM) provides a cross borehole technique to remotely detect abandoned mine works. RIM was used at the Buck Creek Mine, an underground coal mine, to determine the extent of unmapped mine works. The information provided by the RIM survey assisted the mine planners in developing their mine.

Jan 1, 1990

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Gregory M. Molinda

The U.S. Bureau of Mines has developed a rock mass classification system for coal mine roof control. The Coal Mine Roof Rating System (CMRR) evaluates the structural competence of mine roof using simple field tests and observations obtained from underground exposures in roof falls or overcasts. The basis of the WRR is a weighing system which converts descriptive geologic roof rock data to a numerical value, facilitating its use in engineering design. A full suite of data collection and hand calculation sheets accompanies the CHRR A data base is currently being collected from all major coal basins in the United States to validate the CMW. To date, CHRR values are available from 96 roof exposures in 59 coal mines representing these basins. The system can be used to help solve many practical ground control problems, including longwall gate road design, roof support selection, and decisions regarding extended cut length.

Jan 1, 1993

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

By D. W. H. Su

This paper describes geomechanical criteria employed by Consol Energy for selecting mine-specific longwall face supports in the past decade. The criteria include immediate and main roof rock characteristics, floor rock characteristics, critical tip-to-face distance and shield operating range. Detailed roof rock properties from high-density core holes as well as in-mine scope holes are used to evaluate the set load density and shield stiffness required to control the immediate roof and the yield load density required to absorb the load density developed from main roof weighting. Detailed floor rock properties from core holes and in-mine floor bearing capacity tests are used to specify the maximum peak toe pressure as calculated by the Jackson method. The critical tip-to-face distance is evaluated based on the immediate roof rock strength, layering and thickness. The shield operating range is evaluated based on main bench thickness, the presence of thick draw slate, the potential of minor roof falls at the face and transportation restriction. Three case examples representing three different geologic conditions are presented to illustrate the successful application of these geomechanical criteria for selecting longwall face supports within Consol Energy in the past decade.

Jan 1, 2004

A two-dimensional time-dependent analysis of a overburden-coal pillar-weak floor strata interaction problem is presented as a beam model consisting of a composite roof beam resting on multiple elastic foundations (pillars) underlain by a composite rock mass representing immediate floor strata. Several different material models may be considered for the immediate floor strata. The analysis can include all openings and pillars in a panel and permits bed separations in the roof composite beam. The model has enabled identification of the relative significance of different geometric and mechanical behavior parameters which govern the system. The paper presents the theoretical background for the model as well as its application to a mine in Illinois where surface and underground geotechnical observations have been conducted over the last two years.

Jan 1, 1988

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By K. Goshtasbi Goharizi

This paper discusses experimental results of physical scale models employed to study the stability of a pillar between rectangular roadways. A programme of laboratory investigations utilising a bi-axial test rig has been undertaken to examine the influence of various stressfields on the stability of pillars between mine roadways. The effect of pillar height/width ratio on the overall stability is studied. Observations of failure characteristics in and around pillars are discussed especially in relation to the various stressfields applied to the models.

Jan 1, 1992

By Winton J. Gale

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992