Search Documents

By Robert M. Cox

The successful application of the science of rock mechanics to the practical problems of coal mine design requires the acquisition and reduction to useable form of large amounts of field and laboratory data, and the construction and analyses of numerous geostructural models containing a wide variety of geometric and physical strength variables. Typically, the rime constraints placed on a new mine design project coupled with the inherent complexities of a good rock mechanics study combine to limit the applications of rock mechanics to the most rudimentary level. To facilitate a better application of rock mechanics to mine design problems, an interactive software package has been developed for use on a graphic mini-computer system that serves to aid the engineer in the timely and efficient analyses of rock mechanics data and geostructural models. The first phase of the rock mechanics package solicits the input of the raw geologic and rock strength data, analyzes and arranges this data in a logical manner, produces complete listings and statisitical summaries of the various rock properties, and stores the data on magnetic tapes and disks to serve as a future Rock Mechanics Data Base. The second phase of the software package provides for the analyses of a variety of geostructural models using a wide variety of geometric variables coupled with the rock strength data stored in the Rock Mechanics Data Base. This software package allows for the evaluation of numerous geostructural mine models for the design and selection of mine roof support and pillar systems (see Table l).

Jan 1, 1982

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By Brian E. Travis

Recent Developments in the utilization of polymer grid structures for Longwall Shield Recovery operations are discussed. Specifically: various Longwall screen designs and the numerous methods employed during installation. Also discussed is the role of polymer grid structures in head and tailgate mf and rib control and their role in controlling soft bottom often associated in shield recovery operations.

Jan 1, 1993

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By Jinsheng Chen

Longwall mining-induced abutment loads on the surrounding coal pillars can be grouped into two categories in terms of the relative position of the coal pillars and the longwall face. They are the front and side abutment loads. Even though a lot of research and efforts have been made to study the nature and behavior of these longwall mining-induced abutment loads, their influence zones and magnitude are still not well defined and fully understood due to the complexity of geological conditions and the longwall muting-induced overburden strata movement. The uncertainty about the mining-induced abutment loads often forces consultants and mining engineers to employ a conservative approach in designing coal pillars and entry roof control plans. The problems with this approach are that: (a) it increases CM development¬longwall retreat footage ratio, (b) it decreases coal recovery, and (c) it increases !Ill' operating costs. However, a more liberal approach may create safety issues and result in loss of production. Therefore, the importance of accurately defining the influence zones and magnitude of the front and side abutment loads induced by longwall mining can never be over emphasized. The authors in this paper attempt to define the influence zones and discuss the magnitude of the longwall mining-induced abutment loads by analyzing the field data measured at RAG American Coal Company's longwall mines. In addition, the relationship between entry stability and the balance among roof/floor conditions, pillar design, and roof control plan is also briefly discussed.

Jan 1, 2002

By Frank E. Chase

Sacrificial entries, roof slotting, and other tactics have been used to combat high horizontal stresses during roadway development in U.S. coal mines. In Australia, the "pillar extraction on the advance" mining method has been successfully employed as a horizontal stress control technique. The concept of advancing and relieving mine workings through pillar extraction developed from observations that some mines experience difficult ground conditions when advancing and retreating the first panel in a new reserve. However, conditions dramatically improve in subsequent panels. Apparently, the creation of a gob area stress relieves the adjacent panel workings. After much debate and close scrutiny, the first U.S. roof control plan to advance and relieve was approved in 1998, for the Sargent Hollow Mine in Wise County, VA. The major concern was that this mining practice places section personnel inby of the gob. The tentative approval permitted barrier pillar slabbing and removal of the adjacent development pillar during panel development. The intent of the plan was to provide a "stress shadow" for the advancing faces and outby workings to reduce the excessive number of roof falls. Sargent Hollow successfully extracted their first panel by pillaring on advance and retreat mining using posts. Mobile roof supports were employed to extract pillars while advancing the second panel. This paper summarizes Sargent Hollow Mine's experiences with the advance and relieve mining method.

Jan 1, 1999

By Murali Gadde

Among different types of ground control problems associated with underground coal mining, those related to in situ stresses are the most common ones affecting the safety and economy of a mining operation. As a result, this has been the focus of many ground control research works done in the last three decades. This paper summarizes a recent work done on in situ stress related ground control issues of underground coal mine development workings. The approach used in this study was three¬-dimensional finite element modeling by an implicit code, ABAQUS/Standard. In the models, roof stability evaluations were made using Hoek-Brown rock mass failure criterion. Influence of the in situ maximum horizontal stress angle on the stability of both entry and intersection was examined to help determine the best development layout orientation. Also, the effect of in situ stress ratios on the stability of development openings was studied. To make the work more general, both 'low' and 'high' in situ stress fields were considered In general, the modeling results indicated that entries oriented in the direction of maximum horizontal stress were in the best condition while those oriented at 90° had the least stability. For intersections, the maximum and the minimum stability were seen at 0°/90° and 45°, respectively. However, under some combinations of input conditions, the best or the worst conditions were noticed at same other orientations as well. Based on these findings, layout design charts were prepared for both entries and intersections. It was also found that the change in ground conditions with change in layout orientation was more significant for 'low' in situ stress fields than for the higher ones. Change in the average safety factor with change in the ratio of in situ maximum horizontal to vertical stress resembled a lognormal distribution curve. However, the effect of the ratio of in situ maximum to minimum horizontal stress lacked such a clear trend for different input combinations considered.

Jan 1, 2004

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

Jan 1, 2001

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Chris Strawson

Moranbah North is a modern longwall operation mining premium coking coal in the Northern Bowen Basin, Central Queensland. Australia Moranbah North Coal (MNC) is owned and operated by Anglo Coal Australia. Extracting approximately 4.5m of the Goonyella Middle seam using a single longwall, the mine produces 5 to 6 Mt per annum. The weak coal (4.5 MPa), low strength laminated immediate roof, and strong upper roof sandstones, make operation of the longwall at depths in excess of 250m geotechnically challenging. In the past, there have been a number of production delays due to geotechnical issues. Roof instability resulted in a long stoppage on Longwall 105, and the eventual relocation of the face further outbye in the block. (Figure 1). When mining commenced in LW106, there was a requirement for uninterrupted production, particularly in the more demanding inbye area of the panel. Following discussions with a number of Geotechnical experts, it was decided to narrow the face, and test the theories of reduced face weighting due to spanning of the goaf across the panel. A new on line chock monitoring system, and microseismic monitoring was installed in order to characterise the difference in the rockmass response, as the panel width changed from 175m, to 265m, and then 300m. The nature of the goaf formation and impacts on face loading and production are discussed, having the unique opportunity of three different face widths within the same area.

Jan 1, 2007

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981