Search Documents

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By Keith A. Heasley

Exactly 25 years ago this month (August 12, 1981), IBM introduced the ?Personnel Computer? with a 16 bit operating system called MS-DOS 1.0. Since then, Moore?s Law, which essentially states that computer capability will doubled every 18 months, has been fully evident in the computer industry. As computers have advanced from main frames to initial personnel computers to the powerful graphical workstations of today, numerical modeling for ground control in mining has followed closely behind. Twenty five years ago, many numerical methods for solving ground control problems were little more than equations on a piece of paper. In the intervening years, these numerical models have grown from initial trial programs to highly-complex computational systems with numerous capabilities for different material behavior, failure criteria, gridding methods, discontinuities, etc. In some instances, the capability of the programs has quickly outstripped the geo-technical modeler?s ability to get accurate, realistic input and boundary conditions. This paper will look at: how numerical models have evolved in the last 25 years, how the models have been applied to ground control problems in that time period, and where numerical modeling is headed in the immediate future.

Jan 1, 2006

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Peter B. Lilly

Thank you, Syd, for the kind introduction and for inviting me to give the Keynote Address at this very prestigious gathering of some of the finest intellect and talent in the domestic and international coal industry. CONSOL Energy has been a part of this conference for its entire 24-year existence. We have presented 27 papers over that time. CONSOL employees have also been members of the planning committee for the conference, and we have been pleased to support the event both financially and with many participants. So I am honored to be here with all of you this morning, especially during such a positive period for coal. You can just feel the enthusiasm in this room for our industry, and for this conference. I can tell you, there?s also a lot of enthusiasm and excitement in CONSOL Energy?s boardroom. And our enthusiasm is mirrored on Wall Street. But there remains an ironic twist to all of this attention. Even when times are good, the coal industry seems to go largely unnoticed by the mainstream. Outside of West Virginia and other coal-producing regions, the industry still seems to lack influence and support, at least here in America. As an example, last month, an ABC News crew visited our Blacksville 2 Mine, near here, to do a feature story on increased employment in the coal industry.

Jan 1, 2006

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By Panfeng Gou

In order to solve the problems of supporting the roof of the gateroads affected by a fault, the movement characteristics of roof strata must be fully understood. In this paper, a plane stress physical simulation model was constructed to study roof strata displacement and deformation of gateroads driven in the hanging wall of the fault after the coals in the footwall were extracted. The results indicated that, due to the effect of fault, vertical cracks, orienting parallel to the dip of the fault, occurred in the horizontal direction of the model within the areas affected by the fault. The roof strata are discontinuous. On the other hand, non-uniform subsidence of roof strata occurred due to the bedding plane separation in the vertical direction. Roof strata, especially the lower roof strata, dip toward the fault. Failure of the surrounding strata is not symmetrical with the roof and floor close to the fault being deformed severely. In the selection of type of supports for the gateroads, the U-shaped steel supports are superior to roof bolting.

Jan 1, 2006

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006