Search Documents

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By Clyde DeRossett

Surface fractures, sometimes of significant size, are observed in eastern Kentucky over high extraction areas. Field observations were correlated with mine maps and a regional subsidence prediction computer model. The opening of large fractures is attributed to the presence of a pre-mining joint system, which exists near outcrop in the eroded Appalachian plateau. Lithological composition of the overburden influences the process of fracture opening. No correlation was found between the areas of the predicted maximum horizontal extensions and the actual location of fractures. In this paper a mechanism of fracture formation as a result of the high extraction mining is presented, with recommendations for mine planning to minimize surface damage.

Jan 1, 1993

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989