Search Documents

By B. Derin

In this study, the Reddy-Blander model was applied to predict the sulfide capacity (CS) values of FeOx-CaO-SiO2, FeOx-MnOx-SiO2 and FeO-MgO-SiO2 ternary slags, which were experimentally studied in the literature within the temperatures between 1,673 and 1,923 K. As expected, sulfide capacity values of the slags increased with increasing temperature and decreased with increasing acidic content. The model was found to be in agree-ment for all slag systems at the temperature range of 1,773-1,923 K. However, a disagreement occurred when the basic content was relatively high, at 1,673 K for FeOx-CaO-SiO2 and FeO-MnOx-SiO2 slags. The effect on the CS of high amounts of Fe+3 and Mn+3 in the slags is discussed.

Jan 1, 2011

By Gus H. Goudarzi

The apatite deposits in east-central Bahia, Brazil, are about 50 km east of Serra do Jacobina, between lat. 11° and 12° S. and long. 39°40' and 40° W. Apatite was found and examined at 15 localities in a mineralized belt that strikes about N.25° - 30 W. over a distance of about 100 km, but the size of the deposits has not yet been determined. Rocks of the region consist of a sequence of Precambrian migmatites and quartz feldspar paragneisses containing units of pyroxene-rich rocks, lenses of sillimanite-bearing quartzite, amphibolite zones, and calc-silicate marble lenses. Pegmatites and granites of probable anatectic origin (anatexite) are abundant. Faults are numerous. Clastic sediments of Tertiary and Quaternary ages cover most of the area; thus, outcrops of the Precambrian rocks are sparse. Trenches and pits have exposed mineralized zones as much as 10 m wide at some localities within the region. A layer of apatite at least 1 ½ m thick is exposed in a trench at Lagoa do Mel. At Rio do Peixe, vertical shafts have penetrated a mineralized zone, to a depth of as much as 13 m, of which about 25 percent is apatite. Apatite is massive or forms minute crystals, stringers, and disseminated grains in alkalic host rocks. At Apolinario, euhedral crystals of apatite are as much as 50 cm long and 30 cm in diameter. Associated minerals include vermiculite, biotite, scapolite, opal, chalcedony, epidote, montmorillonite, chlorite, kaolinite, sericite, magnetite, and limonite. Apatite is everywhere intimately associated with pyroxene-rich rocks, alkalic syenite pegmatites, and alkalic granite pegmatites. At Panelas-Retiro, apatite is associated with pegmatites, crystalline calcite (vein calcite), vermiculite, and pyroxene-bearing rocks. Analyses of samples show that the apatite is radioactive and rare-earth-bearing. Traces of vanadium and titanium were detected by spectroscopic analysis. The apatite was probably derived from phosphatic zones in the original Precambrian sedimentary rocks and has been crystallized and some mobilized by high-temperature regional metamorphism (higher amphibolite facies) into veins, pegmatites, and along certain preferred beds and fractures. Radiometric and geophysical surveys, in addition to conventional geological investigations, are planned to further investigate the nature and economic potential of the deposits.

Jan 1, 1972

By T. P. Meloy

Understanding the illusive nature of the catastrophic failure of brittle solids is difficult. Proposed is a hypothesis of crack cessation. If, during catastrophic failure, cracks in a brittle solid stop before terminating on a preexisting crack, this hypothesis suggests that the slope of the size distribution curve will be lower. Moreover, this hypothesis suggests that when cracks stop, negative valleys and negative comers appear. Furthermore, particle shapes also change with particle size. While the hypothesis is unverified, it suggests that crack cessation could play a role in the comminution process.

Jan 1, 1996

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By R. Fields

Nevada is primarily known today for its nation-leading production of gold and silver. However, industrial mineral production continues to play an important role in providing construction materials to help make the state the fastest growing in the United States. Aggregate production in Nevada was about 20 million tons in 1991. Most of that was used in construction in the fast-growing Las Vegas area. The state leads the nation in the production of barite and mined magnesite and has significant production of lithium carbonate, diatomite and gypsum. Other industrial minerals produced in the state include specialty clays, silica, lime and dolomite and relatively small production in salt, perlite and dimension stone. Industrial minerals operations are subject to state and federal permitting requirements, especially in the areas of air and water quality and mined land reclamation. As in all segments of the mineral producing industries throughout the nation, the amount and complexity of regulations affecting industrial minerals has increased significantly in recent years. Nevada is no exception.

Jan 1, 1993

In phosphate flotation, more than 90% of the finer fraction (-35, + 150 mesh) is recovered as opposed to 70% of the coarser material (-16, + 35 mesh). On the other hand, coarser fraction is higher in phosphate content than the finer feed. Consequently, improvement in the coarse recovery is highly desired. It was determined on bench scale that emulsification of the collector (fuel oil and fatty acid mixture) can lead to enhanced recovery of coarse particles. Flotation of phosphate with emulsified collector resulted in improved recovery and grade also on the plant scale.

Jan 1, 1992

By J. R. Gaw

Recent events pertaining to U. S. energy needs and development of alternative energy fuel resources have made the American public more aware of past and present coal mining operations, and their impacts on the nation's economy and environment. This awareness has developed rapidly due to increased government involvement and consequent media coverage. This is true particularly in the Western states and in Texas. One of the consequences of this increased public awareness is public concern over the perceived and real consequences of mining operations. Emphasis has been placed on potential releases of toxic and hazardous substances, and possible carcinogens. The result of this public concern is a mounting effort at both state and Federal levels to promote stricter laws regulating the mining industry.

Jan 1, 1992

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

Cost reduction programs can focus on total cost or unit cost, but unit cost is usually the principal objective. The production cost per unit is: [Unit cost = Total cost Production volume] Consequently, any activity that reduces the total cost or increases the production volume will reduce the unit cost. Production volume is increased by (1) maximizing the availability of the production equipment and (2) maximizing equipment performance during periods of operation. Most operations managers routinely focus on volume because the factors influencing volume are generally well understood and congruent with the managers' technical skills. In fact, production volume (as a percentage of maximum achievable capacity) is widely recognized as one of the most significant measures of operational performance.

Jan 1, 1999

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By Slavko Ostojic, V. G. Hill

This paper reviews various bauxite classification schemes with respect to the differences in texture, composition and geological associations of the deposits. It demonstrates that a techno-economic classification, based on: a) associated rock type - lateritic versus karstic, b) content of aluminum ore minerals - gibbsite, boehmite and diaspore, and c) gangue minerals (iron oxides etc.) has a geological basis with natural cut-off points for the bauxite types identified. Thus, this scheme is seen as applicable to bauxite resources. It also provides a basis for their rational exploitation taking into consideration the long-term interests of both the bauxite producing and consuming countries. Against this background, the industrial mineral or non-metallurgical grades of bauxite are seen as localised and relatively rare occurrences. Their consumption should, therefore, be aimed toward the specific (hence more remunerative) products as indicated by the bauxite characteristics.

Jan 1, 1984

By T. J. Fronapfel

Impacts to ground water from mining are being comprehensively regulated in Nevada through specific requirements for design, construction, operation, permitting and closure. This program is the nation's most comprehensive for control of activities at mining operations which have the potential to cause groundwater degradation. It encompasses virtually all types of facilities, including placer, physical separation, flotation, testing, leaching and milling. Minimum design requirements are established by regulation, and must be met by each facility. Site-specific monitoring requirements are established for each facility, and are heavily emphasized. Regulatory and technical requirements and relevant permit conditions are presented and discussed.

Jan 1, 1992

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods.

Jan 1, 1999

By George C. Toland

Tailings disposal has been a problem for the mining engineer since the beginning of the metal milling process. Disposal systems in common use have evolved as the most economic method for the disposal of an unwanted waste material within the disposal restrictions in force at the time of construction. As restrictions are constantly being expanded, the design requirements for tailings disposal systems are also being enlarged. However, proper design will always be to provide the most economic disposal system that will meet current safety and pollution requirements. This paper presents a brief description of some of the design features of tailings disposal systems in common use and presents specific design features of the gypsum tailings disposal pond at Kimberley, British Columbia, owned and operated by Cominco Ltd.

Jan 1, 1971

By Y. Wang, E. Forssberg

Wet magnetic separation methods for the recovery of hematite and chromite fines and ultrafines were investigated. These methods included wet high-intensity and high-gradient magnetic separation, carrier or "piggy-hack" magnetic separation, magnetic field-induced aggregation and magnetic seeding. This investigation indicated that wet magnetic separation is more efficient for fines and ultrafines. This investigation also indicated that other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behavior of these minerals with respect to the magnetizing field, temperature and particle size is also presented.

Jan 1, 1995

By E. J. Rorem

Rockfall and unstable rock slopes can be effectively controlled by utilizing steel wire rope net systems, either as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting, permitting kinetic energy dissipation, yet providing high strength and consequently low maintenance. A review of the design considerations involved with these systems, as well as a review of several mine and non-mine installations is presented with the hope that the information may contribute to the safety against the dangers of rockfall and other mine hazards in active and abandoned mines.

Jan 1, 1996

By James D. Bliss

Evaluation of data for three engineering variables-absorption, bulk specific gravity, and freeze-thaw durability (350 cycles)-was made for quarries in carbon- ate rocks in Oklahoma that supply aggregate. It was found that lower Paleozoic carbonate rocks (Cambrian through Devonian) are likely to make a better quality aggregate than upper Paleozoic (Mississippian to Permian) carbonate rocks. In addition, freeze-thaw durability can be forecast from absorption and is exemplary for lower Paleozoic carbonate rocks.

Jan 1, 1999

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

By Robert H. Shannon

Coal is the primary fuel for U.S. electric per generation -- over 78% of U.S coal production. In 1987 over 56% of electric per generation was from coal-fired plants. Areas of concern confronting the expanded use of coal for per generation include environmental, political and the nation's energy security and economy. These matters and available alternatives and options directed to the expanded use of coal are reviewed.

Jan 1, 1989