Search Documents

By Y. Luo

"Investigating abandoned mine subsidence is often a difficult task because many factors, both mining- and nonmining-related, can affect the possibility and the formation process of surface subsidence events over abandoned underground room-and-pillar mines. Among them, mine water frequently plays an important role in causing such subsidence events. However, mine water could also serve the purpose of preventing subsidence. The dewatering of abandoned room-and-pillar mines has been identified as the main cause for a number of serious mine subsidence events in the past.In this work, the mechanism of mine water to prevent surface subsidence over abandoned room-and-pillar coal mines was studied. Two mathematical models are proposed to quantify the potential effects of mine water on the structural stability of mine pillars, roof and floor as well as the potential for causing surface subsidence. The models are validated with an actual case. IntroductionThe potential for room-and-pillar mining operations to induce surface subsidence is mainly dependent on the recovery ratio in the underground mines that directly relates to the stability of pillars. Normally, if the recovery ratio is less than 50 percent, the mine pillars are sufficient to support the overburden strata without their collapse in a sufficiently large contiguous area. Consequently, there will be no surface subsidence. However, if the recovery ratio is greater than 70 percent, the pillars are too small to support the overburden strata and can cause immediate surface subsidence. In 1993, a mathematical model and program was developed and proposed (Luo and Peng, 1993) to predict surface subsidence caused by high-extraction, roomand- pillar mining. When the recovery ratio is between 50 and 70 percent, the mine pillars could be loaded near their critical condition and, therefore, the surface subsidence is uncertain to develop. If the surface subsidence did not occur immediately, mine water starts to fill the underground openings. If thick, clay-type rock layers are presented in the mine roof, floor or pillars, they can be considerably weakened by mine water and cause surface subsidence. The techniques to investigate subsidence events over inactive room-and-pillar coal mines caused by the weakening effects of raising mine water to the claystone immediate roof and floor were presented in Luo (2009, 2011)."

Jan 6, 2018

By F. Calizaya

This study summarizes the ventilation requirements for a highly mechanized P.T.Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The Deep Ore Zone (DOZ) is a copper-gold deposit being developed underneath the current Intermediate Ore Zone (IOZ) mine. One of company's current plans is to prepare this mine for a steady oreflow of 25,000 tpd by year 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 1998

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By John Duff Erickson

Computer use has become an integral part of mine planning at Kennecott Copper Corporation?s Utah Copper Division, Bingham Canyon mine. Engineers are using the computer for development drilling calculations, mineralization grade interpolations, ore value summaries, long-range mining plans and short- range mining plans. The versatility of the computer has made it possible to explore many mining plan variations and to develop plans covering varying time intervals and production rates. This paper will summarize computer use in long-range mine planning, tell how short-range mining plans are prepared by conventional methods and discuss the development and application of short-range mine planning by computer.

Jan 1, 1966

By Robert R. Brandom

The Boss-Bixby deposit is one of several iron deposits that occur in the Precambrian igneous rocks of southeastern Missouri. It differs, however, from all of those deposits by its significant contents of copper, cobalt, and titanium, and its close relationship with a basic igneous intrusion. Ore microscopic study of selected drill core samples has shown that the hypogene ore minerals are magnetite, hematite, chalcopyrite, bornite, covellite, ilmenite, rutile, sphalerite, cobaltian pyrite, carrollite, scheelite, and wolframite. Subsequent partial oxidation has formed martite, pseudobrookite, and anatase. Textural evidence indicates that two stages of iron and iron-titanium oxide formation were followed by the deposition of the copper-iron sulfide minerals and carrollite.

Jan 1, 1985

By R. M. Clowes

LITHOPROBE is a collaborative, multidisciplinary research project that is providing new insights into the tectonic evolution of the North American continent through its work within 10 study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of the tectonic processes that lead to the development of ore deposits. In mining camps, seismic-reflection methods have proven effective in imaging shallow to moderately dipping lithologic contacts as well as structural features and, in some cases, have been used for the direct detection of orebodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 2002

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971

By M. L. Smith

The U.S. Bureau of Mines Cost Estimating System (CES) has been used for prefeasibility analysis and mine cost engineering since 1978. In the past, prefeasibility analysis with CES has involved the solution of regression equations. The new generation of CES uses an object-oriented expert system in a Windows? environment. Knowledge bases are structured around generic mine models which access shared knowledge bases for system design.

Jan 1, 1994

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By Robert A. Bauer

Geology and weather effects produce natural ground movements that may be misinterpreted as mine subsidence. Weather, local geology and vegetation clearly influence the elevation of the ground surface through frost action and changes in groundwater levels and soil moisture content. Common practices of monument and benchmark design and placement do not address the problem of natural ground movements. Monuments can be designed to minimize some natural ground movements. Differential displacements can be reduced by knowledgeable placement of benchmarks and monuments which are of similar design and construction. Commonly, the threshold values of movement for the determination of mine-induced subsidence are dependent on the closure errors (accuracy) of individual surveys. Accuracy is more than the amount of closure error; it should include the range of elevation changes (error band) determined for each monument over a period of time before it is disturbed by mining. Multiple baseline surveys of the entire monitoring system, conducted before the onset of subsidence, should be used to establish subsidence detection limits.

Jan 1, 1986

By K. Norris

The Amax Gold Guanaco mine is located in the Atacama Desert, approximately 260 km southeast of Antofagasta, Chile. The 6,000 tpd leach operation produces approximately 90,000 oz of gold, and 360,000 oz of silver per year. Production began in 1987, and the operation has been managed by Amax Gold since 1992. The mine has been plagued in the past by high operating costs and low production. Several significant changes have been made to the operations which have resulted in lower costs and higher operating efficiencies. A review of these changes is presented herein.

Jan 1, 1997

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By Harold L. Hinds

The refining of precious metals from steel wool cathoodes is completed by one of two methods: 1) By direct fire smelting or: 2) Acid treatment of the cathodes to dissolve the steel wool and then followed by fire smelting. To further the refining of the cathodes, the Miller Process and the Wohlwill Process are used.

Jan 1, 1981

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

By Dan J. Van Roosendaal

A closely spaced grid of survey points was installed over the tensile zone of a longwall panel in southern Illinois and monitored daily during subsidence to document the complex ground-surface movements associated with dynamic subsidence. Vertical and horizontal displacements were used to calculate maximum tilts and principal strains within the grid. The dynamic nature of subsidence is made evident by changes in both the direction and magnitude of maximum tilts and principal strains. The maximum tilt (smax) of 0.036 and maximum tensile strain (Emax) of 0.027 were measured after subsidence and were oriented transverse to the longwall panel. Observations of surface fracturing were correlated with strain determinations to estimate a surface strain at incipient cracking (E;) of 0.006 to 0.009. Using shallow inclinometers, a linear variation of horizontal displacement with respect to depth was observed, suggesting a neutral¬axis bending mechanism for near-surface deformation. Horizontal displacements transverse to the longwall panel reduce to zero at a depth of 40 feet. A linear relationship between strain and curvature was used to estimate ground-surface curvatures associated with Emax (0.00068 ft-1) and E; (0.00015 to 0.00023 ft-1). The curvature estimates are consistent with published results.

Jan 1, 1986

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992