Search Documents

By Francois E. Heuze

Excavation of large rock caverns is a stepwise process. Whether one uses a heading and bench method or a multiple drift system, the use of excavation steps enables one to introduce the reinforcement, such as bolts or shotcrete, at the earliest possible stage. Knowing the spatial distribution and properties of rock materials and geological discontinuities, the cavern geometry and its reinforcement must be optimized. The finite element method of analysis is a powerful tool for such optimization. However, the models are only as good as their ability to account realistically for the physical attributes of the prototype and for the excavation sequence. They must include the following: - ability to model an incremental construction process. Thus requires the use of "Restart" procedures where displacements and stresses from a previous equilibrium are saved for the next step. - ability to model non-linear rock material behavior; in particular, the post-peak behavior of the rock which retains a residual strength when con-fined. The stability of many under-ground structures rests with the "broken" rock carrying significant loads. - ability to account for the non-linear behavior of geological discontinuities. These are two-fold. First, up to peak, non smooth rock joints will dilate. In a confined situation, dilation will increase joint strength by a consider-able amount (Obert, et al, Brady, 1971, Heuze,1978a), Then, beyond the peak, the joint also retains residual strength.

Jan 1, 1978

By Peter T. Luckie

Up until the past couple of years, thermal coal dryers were only used to dry midwest and eastern United States bituminous coals. These dryers were primarily installed at coal preparation plants to freeze proof the coal and lower the transportation costs per BTU. Today thermal coal dryers are being specified to dry western sub-bituminous and lignite coals for these and other reasons brought about by the intense interest in coal gasification and liquefaction. One reason for drying western coals ahead of a coal gasification plant is the elimination of surface moisture which would prevent efficient sizing of the coal, since feed material size consist is very important in most commercial coal gasification processes. Thermal dryers are being proposed for liquefaction processes because of the need for a feed material containing approximately 4% or less total moisture Future coal gasification processes may also need to reduce feed material moisture content.

Jan 1, 1975

Underground mining has the potential to be one of the more dangerous industries in the United States and the world. Following recent disasters in Sago, WV; Darby, KY, and Crandall Canyon, UT, the mining industry was reminded of the need for a system to allow trapped miners awaiting rescue to survive following a disaster. To address this need, Battelle has developed a Mine Barrier Survival System (MBSS) that surpasses all current technologies and sets a new standard for keeping miners alive in the event of a fire, flood, explosion or collapse. The MBSS creates a temporary refuge for miners who cannot escape by using inflatable barriers and a post-fire atmosphere scrubbing system to define the ?safe haven? and remove CO2 and CO while replacing oxygen and providing heat. Current personal-protective systems in use are designed to provide breathing air for only a few hours when, realistically, it may take days for rescue teams to reach trapped miners. Battelle?s MBSS is designed to aid up to 15 miners for four days.

Jan 1, 2008

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By M. Liu

In-situ soil washing using surfactants shows great potential to remove hydrophobic organics from subsurface environment. Lab scale soil washing experiment were performed using Sodium Dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that solubility of anthracene increases linearly with an increase in SDS concentration above the critical micelle concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1992

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By M. Z. Rashad

The intersections of numerous joint sets at the surface of tunneling region of Abu-Tartour-Project in Egypt create blocks with irregular shape and size in the rock mass. Most of these blocks are not able to move into the free space of the tunnel. Few key blocks are in a position to move and as soon as they begin so, some restrained blocks will be liberated. The aim of this work is to find the (removable) key blocks for walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks; and then determine the best tunnel direction.

Jan 1, 1991

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature dependent physical properties of frozen rockmass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite element model for analysis of the effects of roof bolting in a frozen rockmass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rockmass, creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected, and shows that, for a given set of rockmass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1996

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By Bruce C. Trent

The need for effectively evaluating the potential for surface subsidence due to under- ground mining has been widely documented. As the emphasis within the coal mining industry changes to reflect the increasing demand of this resource, the potential for damage due to differential surface subsidence will certainly become more acute. The present state-of-the-art of predicting ground motion due to underground excavations is, at best, primitive when one considers the immense complexity of possible geological inter- actions. For the most part predictions have been limited to empirical evaluations based upon earlier case histories. While the tools of the subsidence engineer are limited, they are important and serve to provide reasonable bounds for possible ground motion. As underground mining becomes more extensive, however, there will be many instances where excessive subsidence will be most undesirable and yet there may be few, if any, case histories similar to the operation in question.

Jan 1, 1982

By R. M. Barker

The historic Getchell property is currently being mined from the Getchell Main Underground workings, a foot wall extension of the Getchell open pit deposits along the Getchell fault. Drift-and-fill techniques are used to extract the ore through a ramp access. The adjacent Turquoise Ridge deposit is currently under development via two vertical shafts. Together, the two mines will continue to provide feed to the Getchell's 3,200 tpd mill/autoclave circuit, taking Getchell Gold from its current production rate of 200,000 ounces (Au) per annum, to over 400,000 ounces (Au) per annum by 1999.

Jan 1, 1997

By J. A. Madonna

Universities and colleges in three countries, Australia, Canada and the United States, recognized the need to establish and/or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral industry organizations cooperated in the study by providing information regarding their specific training needs for support personnel. The data gathered has been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration, including, but not limited to, geological skills, geochemical skills, environmental skills and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will be discussed.

Jan 1, 1993

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By E. J. Berentsen, R. F. Nanna, D. Dell’ Elce, R. Lougheed

Apollo Gold’s Black Fox project is located 10 km (6.2 miles) east of Matheson, Ontario, Canada, on Hwy 101 East It is located within the prolific Destor Porcupine Fault Zone, which is also the host for the Dome and Hollmger mines to the west and the Holt and Holloway mines to the east. The local host rocks are intensely deformed and carbonized ultramafic volcanics, pillow basalts, syenitic felsic intrusives and argillaceous sediments. Gold occurs with pyrite and as spectacular specimens in native form. Past production accounted for a total of 195,337 oz (6,075,606 g) of gold. Apollo Gold Exploration, Inc. is conducting an intense drilling program aimed at expanding the reserve base.

Jan 1, 2004

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. Manea

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra). Ecological remediation aims, among others, at decontamination of soils by preserving important properties as soil fertility.

Jan 1, 2008