Search Documents

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By Michael Jatczak, Brett Robinson

The South Bay Ocean Outfall tunnel is located at the U.S./Mexico Border and is one link in a system designed to treat and dispose of raw sewage entering the Tijuana River Valley from Mexico. The 11 finished diameter tunnel extends 19,000’west from the bottom of a 200 deep, 36 diameter drop shaft. At the western terminus of the tunnel, a Riser shaft connects the tunnel to conveyance and diffuser pipes on the seabed. The tunnel runs through the San Diego Formation, consisting of clay, silt, sand, gravels, cobbles, and boulders. A Mitsubishi Earth Pressure Balance (EPB) Tunnel Boring Machine equipped with a large variety of monitoring and control devices was used. This paper will provide an overview of the Project’s construction, with special emphasis on the value of the electronic data acquisition system.

Jan 1, 1999

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By M. P. Miano

Matching the productivity gains of continuous mining machines with the ever increasing performance levels achieved by longwall units has required creative thinking to assure that development is completed in time for uninterrupted longwall production. By using management information systems to coordinate support operations, the most productive planning decisions can be made. This paper focuses on the role of computer technology tools in achieving improved productivity from both longwall and continuous miner sections. The primary emphasis is on the planning process and the methodology developed to guarantee the best allocation of management and manpower resources.

Jan 1, 1993

By Prashanta K. Chatterjee

The planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc, do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered. Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate many layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment.

Jan 1, 1986

By B. Kolonja

A SIMAN and CINEMA PC-based simulation model was developed to simulate and animate the truck-shovel operations of surface mines. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. The statistical analyses were performed and appropriate theoretical distributions were fitted for various time events in the truck-shovel work cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an 'optimal" dispatching strategy to produce an equilibrium between "the quality and quantity of production.

Jan 1, 1993

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

The strength of anchorage of various types of roof bolts in permafrost depends on the types of rock in which they are installed. Variation in the mine thermal regime results in weakening of the roof and walls, and at times total loss of ice cement bonds takes place in the surrounding rockmass. In mines with positive ventilation air temperature, the wedge or expansion types of bolts may become weakened due to the transfer of heat into the anchorage through the metal rod and subsequent thawing of rocks. Effective operation and evaluation of roof bolt systems for mine workings in permafrost require predictions of the dynamics of wall thawing by warm ventilation air. This paper presents an analysis of the temperature distribution in the frozen host ground surrounding roof bolts, the area of interest being the vicinity of the anchors for point anchored bolt and the entire length for split set bolt

Jan 1, 1994

By J. K. Whyatt

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations of in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence from the Lucky Friday Mine collected by U.S. Bureau of Mines researchers, as well as a review of case studies, demonstrates that in situ stress variations affect the spatial distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies, they are too expensive and, depending on conditions, may be too difficult, to use routinely in mapping stress variations. However, information from borehole and raisebore breakouts; deformation of mine openings; and patterns of seismicity, ground control problems, and rock burst damage can be used to build a stress database. This database can then be used in con-junction with maps of mine structure and geology and models of rock mass behavior to build a map of in situ stress variations. Such a map provides a means to anticipate patterns of mining-induced seismicity that are likely to be encountered and, hence, provide a means for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1995

By J. F. Hunt

[THE AUTHOR DESCRIBES THE ACTUAL PROCESSING OF THE GOVERNMENT STOCK¬PILE OF CHROMIFEROUS SANDS. LOCATED AT COQUILLE. OREGON, DURING 1955 AND 1956. A GENERAL HISTORY OF THE STOCKPILE IS GIVEN, ALONG WITH A BACKGROUND OF THE GEOLOGY AND ORIGIN OF THESE SANDS. THE FLOW SHEET USED IN THIS OPERAT ION IS OUTLINED IN DETAIL, AND THE MINERALS WON FROM THE STOCKPILE BY HIGH TENSION AND MAGNETIC PROCESSING ARE DISCUSSED AS TO THEIR PURITY AND SALEABILITY. AMONG THESE MINERALS ARE CHROMITE, ILMENITE, MAGNETITE, ZIRCON, GARNET, RUTILE, MONAZITE, GOLD, AND PLATINUM. PLANNED POST-STOCKPILE OPERATIONS ON THE PRESENT BEACH DEPOSITS ARE DISCUSSED. THESE OPERATIONS WOULD HAVE BEEN CARRIEDOUT TO SET UP A' CONTINUOUS INTEGRATED MINING AND BENEFICIATION PROJECT, EXCEPT FOR UNFORESEEN CIRCUMSTANCES WHICH DICTATED THE CLOSING OF THE OPERTIONS AT THE EXHAUSTION OF THE GOVERNMENT STOCKPILE. THE PAPER IS ILLUSTRATED WITH MAPS, FLOW SHEETS, CHARTS; AND PHOTOGRAPHS OF STOCKPILE, PLANT, AND EQUIPMENT.]

Jan 1, 1964

The effects of additives, sodium hydroxide, sodium carbonate, sodium oleate, oleic acid and polyacrylic acid, on stirred media milling of limestone have been investigated. The results are evaluated in terms of specific surface area, specific energy and energy efficiency as a function of additive dosage, polymer molecular weight, solids concentration and relevant operating variables. Use of additives generally results in changes in specific surface area and energy efficiency, while under certain conditions a more than 100% increase in these parameters can occur. Relevant interfacial properties have been measured and milling mechanisms involved are explored particularly in terms of the effect of additives on the flow patterns at higher solids concentration.

Jan 1, 1996

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993