Search Documents

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonite to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath. 1986 and personal communication). These bentonite; typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X- ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated bentonite to the oilfield since specifications are

Jan 1, 1990

By George H. K. Schenck

INTRODUCTION Boom-type miners mechanize the cutting and loading of a solid face of rock having a compressive strength as high as 124 MPa (18,000 psi). These machines differ from continuous miners in that they can cut much harder rock for any given cutter-motor power. In addi¬tion, a boom miner is more flexible, selectively cutting any cross-sectional configuration from circular to square arched faces, 1.57-rad (90°) turns, and mixed faces. The basic operational concept of these machines, utilizing a rotary cutterhead mounted on a slewing boom, gained importance in Europe during the 1960s, where, due to their specialized use in roadway development in coal mines, they were called roadheaders. Along with continuous miners, boom miners share the ability to fully mechanize the cutting and loading of rock, while eliminating the need for explosives and the shattering and overbreaking of roof and rib rock that is normal with conventional mining methods. The machines are crawler-mounted and most have a gathering-arm load¬ing system that, moves the cut rock onto an internal chain conveyor, subsequently discharging the rock into a transport device such as a shuttle car or a bridge conveyor. Light- to medium-weight boom miners are cutting softer rocks and minerals successfully, including coal, shale, rock salt, potash, phosphate, weak sandstones (e.g., those associated with uranium ore), and other softer ores such as iron. Heavy third-generation ma¬chines have extended rock cutting to much harder ores such as borate, oil shale, and almost all rock associated with coal seams, except for the harder sandstones and limestones. The mention herein of specific manufacturers, brand names, or models is made by way of example only and does not constitute endorsement by the author or The Pennsylvania State University. All costs cited herein are in 1977 US dollars. TYPES OF BOOM MINERS All boom miners utilize drag bits fixed on a rotary cutterhead that is powered by an electric motor mounted in the slewing and elevating cutter boom. The cutter¬head is either a ripping or a milling type, and the machines have evolved through three generations (Boldt, 1977). As shown in Fig. 1, only one boom miner cur¬rently produced can use both ripping and milling cutter¬heads on one machine. Table 1 lists boom-miner models built in large num¬bers and/or successfully used or marketed in North America. Table I excludes machines of which only a few have been produced and none sold in North America, such as those manufactured by Demag, Eick¬hoff, Paurat, and Thyssen-Rheinstahl. The only Ameri¬can boom miners are the F-16 and Super ROC¬MINER"', manufactured by AEC, Inc., State College, PA. Machine Generations Three generations of boom miners can be distin¬guished according to their times of introduction, their rock-cutting abilities, and their weight classifications. Fig. 2 illustrates typical best-practice production rates possible from boom miners for selected cutter-motor power sizes (other power figures can be interpolated). Productivity is related directly to the energy applied to the cutterhead and indirectly to machine weight; higher

Jan 1, 1982

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60&apos;s increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

By G. Le Bel

Discussion by G. Le Bel The paper proposes three methods to determine optimum lifetime of a mining project 1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project&apos;s potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: •It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. •The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate. Discount rate selection The opportunity cost of capital represents the rate of return that would be obtained if the capital was instead invested in other opportunities considered to exist. Such opportunities must be bypassed if the available capital is invested in the project studied 2. If these other opportunities carry risk similar to the project under analysis (for example, if they are other mining projects), there is no need to add incremental [ ] risk factors. On the other hand, if these opportunities are represented by the acquisition of government bonds yielding 7%, a risk premium factor must be included. The types of risks associated with a mining venture are shown in Table 1. Together they represent the "business risk" of being a mining company. The individual project risk is important to investors if it differs substantially from the business risk of the company and that of the other investments in mining ventures that we must pass up to invest in this particular project. A risk premium or discount would then be required. This can be illustrated by the following example. Consider that a company has two investment alternatives: one is the Cavender hypothetical project located in Nevada, and the other is the same project located in a civil war zone of central Europe. The second project requires a risk premium factor on the discount rate. Conversely, a project showing highly uncertain returns that are negatively correlated with the returns of the firm&apos;s other assets may decrease the company&apos;s corporate risk. Deterministic character of NPV calculation The cash flows used in NPV calculations are obtained from a set of variables. These variables are estimated using one parameter obtained from the engineering studies. Each parameter is thus a single value that is often termed a "realistic" or "best estimate" as opposed to "optimistic" or "pessimistic." However, considering that each variable can assume a range of values between the

Jan 1, 1994

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

By Keh-Jian Shou

"This study adopts and analyzed a shield tunneling case in Taiwan, with a diameter from 5.25m to 6.70m and the smallest radius of curvature 100m, which was constructed in gravel formations as well as a vibration sensitive area. In this case study, a vibration monitoring plan, comprising the sensors inside the shield machine and on the surface, was proposed and performed to provide the vibration data during the construction. In this project, the major vibration reduction considerations were increasing the open ratio of the cutter head (to reduce the cutting function) and reducing the rotational speed of the cutter head. The results of the construction suggest the appropriateness of the above considerations. The findings could provide suggestions to the other similar shield tunneling cases. INTRODUCTION Underground vibrations during shield tunneling are typically isolated and absorbed by the soil. However, a portion of these vibrations may disseminate to the surface. These vibrations are considered micro-vibrations, which generally do not pose a threat to surface structures, and are thus seldom the focus of research. The present project was located in the Hsinchu Science Park where shield excavation bypassed numerous high technology manufacturing plants (e.g., wafer manufacturing plants). The vibrations generated by shield tunneling may affect the vibration-sensitive manufacturing equipment and instruments in these plants, and induce problems in manufacturing processes. Therefore, research to comprehensively understand the characteristics and potential influence of such vibrations is essential. To clarify the characteristics and potential influences of vibrations generated during shield tunneling, the vibration level in the excavation of the Taoyuan International Airport Access (TIAA) Metropolitan Rapid Transit (MRT) Project was examined, as it possesses similar excavation conditions to the present project. The parameters collected from relevant tests were provided as a reference to the firms along the excavation route of the present project to explain the effects of vibrations, and to relevant units for shield machine selection and project execution. No yield problems resulting from shield machine induced vibrations were reported by the firms, and the vibration levels measured in the present project were comparatively lower than those in the TIAA MRT Project. Because the related literature is scarce, this study aims to analyze the collected measurement data and provide suggestions on shield machine selection or designs. Such that we can more properly evaluate and control the impact of shield tunneling induced vibrations in similar projects."

Jan 1, 2016

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By S. Hearn, S. Boskovic, A. Smethurst

"The digestion of minerals in strong acids or at elevated temperatures can result in the release of large amounts of silicic acid which can polymerize in solution to form colloidal silica and gels. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Huntsman’s POLYSIL® polyether coagulants have a “lock and key” relationship with the surface of colloidal silica to help lower the concentration of these particles in solution, improve process efficiency and reduce reagent losses by minimizing crud formation. This paper investigates some of the issues caused by colloidal silica in hydrometallurgy processes and illustrates how the use of POLYSIL® coagulants has helped to improve process outcomes. INTRODUCTION Coagulation differs from flocculation in a number of ways. Coagulants are relatively small molecules that modify the surfaces of fine particles, weakening repulsive forces between them and allowing particles to stick together, while flocculants are generally molecules that are large enough to bridge the boundary layers between the particles. With flocculation, addition rate and mixing all make a difference to the flocs formed. Coagulation, on the other hand, is an equilibrium process. With coagulation it is only necessary to achieve good mixing, and coagulates will form as Brownian motion pushes the particles into each other. In real systems, this process is complete within seconds. Huntsman’s POLYSIL® polyether based coagulants have a strong affinity with the surface of colloidal silica formed by the polymerization of silicic acid. While silica found in minerals has a low aqueous solubility, large amounts of silica as silicic acid can be released as these minerals are digested in strong acids at elevated temperatures. The solubility of free silicic acid is about 150 ppm under pH conditions typical in acid leach environments (1), so the bulk of the silica will polymerize in solution to form colloidal silica. Colloidal silica can pass through a hydrometallurgy process without affecting any of the operations. However, it can cause a number of problems. These include gelling in a leach, interfering with flocculation or crystallization, initiating crud formation (2,3,4), decreasing extraction kinetics and increasing phase disengagement times (5,6) in solvent extraction. In these cases, coagulating the silica with POLYSIL® coagulants can reduce or eliminate the problem by enabling these particles to be flocculated and removed from the solution."

Jan 1, 2015

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

"The mining industry suffers from a number of incorrect perceptions, one of which is that it is an outdated industry that has not changed for hundreds of years. But the truth of the matter is that mining is a vibrant, highly complex industry that not only employs highly skilled and educated professionals but is also often on the cutting edge of technology. It is an industry with projects that are ever-evolving and among the most challenging engineering feats in the world.Take for instance the U.S. 53 Highway Relocation project in Virginia, MN. While more of a civil engineering job than a traditional mining project, it is still a complex engineering challenge taking place in a mining environment that has called on the skills of eight state agencies, three federal agencies, a host of contractors and many consultants, including many from the local mining industry in the Iron Range of Minnesota.In 1960, the Minnesota Department of Transportation (MnDOT) constructed U.S, Highway 53 on a private easement owned by US Steel that cut across a massive taconite deposit. MnDOT constructed the highway with the agreement that if the highway needed to be moved to access the taconite deposit before 1987, US Steel would foot the bill. And if the move was required after 1987, the responsibility would fall to MnDOT. In 2010, MnDOT received the notice that the highway would have to move as property owner United Taconite planned to access the ore, setting in motion one of the greatest engineering challenges, and the highest risk project, in the history of the states’ transportation department.Pat Huston, U.S. Highway 53 Relocation project manager, opened the 90th SME Minnesota Section Conference in Duluth, MN on April 19 with a presentation about the project that includes 5 km (3.2 miles) of fourlane highway and a new 345-m (1,132-ft) bridge that will be the tallest in Minnesota when it is completed later this year.“This project was not business as usual,” Huston told the packed crowd. “Highway 53 connects Canada and the Iron Range to Duluth and Lake Superior. It is an important highway.”During his presentation he spoke about many topics that were familiar to the more than 1,100 mining professionals who attended the conference. In his keynote speech,"

Jan 6, 2017

"The 33rd annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 5, 2015. Each year, one living Hall of Fame inductee, two Medal of Merit recipients, several honorees from Mining’s Past, an Industry Partnership Award and a Special Citation are recognized for their respective contributions to the mining industry.Conrad E. Huss, cofounder of M3 Engineering & Technology Corp. located in Tucson, AZ, will be honored as the 2015 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Huss has served his company as chairman of the board for its entire 30 years and guided M3 to become a full discipline firm. Now M3 offers complete project execution through engineering, procurement and construction management procedure and has become a major engineer of large observatories around the world. The company now has more than 1,000 employees with offices in Arizona, North Carolina, Mexico, Argentina and is incorporated in Guatemala, Peru and Canada.The Medal of Merit will be awarded to Charles Michael (Mick) Lownds, founder of his eponymous consulting firm in Salt Lake City, UT, for his 42 years in commercial explosives following tenure at Sasol and at Orica. Originally from South Africa, Lownds immigrated to the United States in 1998 and has made significant advancement on electronic initiation systems. Lownds has published numerous technical papers, is an inventor with 12 awarded United States patents and was also the recipient of the President’s Award from the International Society of Explosives Engineers in 2000.Medal of Merit for young professionals will be awarded to Fiorella Giana, Freeport- McMoRan Inc.’s (FCX) mine manager at Bagdad. Born in Buenos Aires, Argentina, Giana left the small cattle farm where she was raised in 2001 to pursue higher education in the United States. For the past decade at FCX, as a result of her extraordinary combination of technical skill, leadership and commitment to excellence, she has been given positions of progressively greater responsibility from an entry level engineer to senior mine engineer, to chief engineer and now as mine manager, a position rarely held by woman."

Jan 1, 2015

By Bruce Watzman

Can the United States mining industry achieve its long-stated goal of zero fatalities ? and what will it take to do so? Does it require new laws and regulations, as some propose, and a continuation of the commandand- control model that has been born out of more than 40 years of regulation and enforcement under the Federal Mine Safety and Health Act of 1969? Or, is it time to consider a new model to manage safety and health and drive continuous, sustained improvement? These are questions that many are debating as mine safety performance, while improved, appears mired in a trough where improvement followed by declines seems to have become the rule rather than the exception. Without doubt, U.S. mines have made significant progress in safety performance during the last four decades, yet the stalled decline in fatality numbers, the industry?s report card of its success or failure, has led some to question whether the industry will achieve zero fatalities in U.S. mining by relying solely on the Mine Act?s framework and implementing its regulations. These are questions the CEO-led task force, set up by the National Mining Association (NMA), considered as it sought to identify impediments to zero fatalities posed by the current regulatory regime. Out of that effort came CORESafety, a common safety and health framework that relies on a management system approach to improve safety and health performance. The goal of CORESafety is to achieve zero fatalities and a 50-percent reduction in the rate of injuries in U.S. mining within five years ? 0:50:5. CORESafety is built on the plan-do-checkact model, which has been successfully deployed by industries, mining and nonmining alike, to drive continuous improvement in safety and health performance. The improvements in safety performance that can be achieved by shifting from a command-and-control regulatory approach to a risk-based systems approach built on the plando- check-act model have been documented in numerous industries. For example, the United Kingdom quarrying industry (Fig. 1), not satisfied with the number of reportable accidents being experienced 1995-2000, established a hard target of a 50-percent reduction in the number of reportable accidents during the period 2001- 2005. Having met this target, the industry then established a further target zero for the period 2006-2010. The mechanism to achieve these reductions? The plan-do-check-act model.

Jan 1, 2014

By Nathaniel Arbiter, Brij M. Moudgil

Separating oil shale from waste material or into high- and low-grade fractions can have a major economic influence on the surface retorting process. Different shale rock components vary significantly in physical and surface chemical properties, such as specific gravity, color, and water wettability. Various techniques that use the differences in one or more of these properties have been proposed to preconcentrate oil shale before retorting. This article discusses some proposed techniques, such as gravity separation, sorting, and froth flotation. Retorting oil shale is the most common method for recovering oil from the rock. This process is accomplished either underground (in situ) or above ground (ex-situ or surface retorting). Both techniques have serious limitations, such as low recoveries in the underground method and the ability to process rich shales only in the above ground retorting method. Also, environmental problems are associated with both techniques. Some of these limitations could be overcome if feed to the retorts is of consistent grade. This could be achieved by selecting appropriate sites for in situ retorting and selective mining for surface oil shale retorting. Both of these, however, would have a serious economic impact on shale oil recovery. Obviously, little control can be exercised over preparing feed material in the in situ retorting process, but beneficiation of oil shale could definitely be advantageous in surface retorting, and should have positive influence on the overall economics of recovering oil from the shales. For example, preconcentration of mined shale could result not only in reduced costs for materials handling, but also in waste disposal costs, since waste characteristics before and after the retorting process are significantly different. Upgrading the oil shale might also allow substitution of alternate technology for retorting as well as extend the process to recover oil from marginal deposits. Also, the separated material may become a potential source for recovering other values from shale deposits. Overall, the incentives for preconcentration are to reduce costs and improve thermal efficiency of the recovery process. Oil Shale Properties Important to Preconcentration Oil shale is a carbonaceous rock assaying 5-30% organic material (kerogen) and 70-95% ash-forming minerals. Kerogen is soft, nonbrit¬tle or semi-brittle material, and generally forms a matrix between irregularly distributed mineral grains. Inorganic mineral mat¬ter-quartz, feldspar, dolomite, kaolinite, dawsonite, and nahco-

Jan 9, 1982

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation&apos;s first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12&apos;, 16&apos;, and 20&apos; lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979