Search Documents

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By Clarice L. Amaral, Ricardo Melamed

Clay-coating has been used as an environmental technology tool for the immobilization of toxic elements. The mechanisms of arsenate retention in clays suggest that not only the system pH is of fundamental importance in the process but also the character of metals and ligands that compose the electrolyte system. The goal of this study was to investigate the interactions between system pH and electrolyte ions on the retention of arsenate in an Oxisol soil. The sorption of arsenate decreases with the increase in system pH, reflecting the competitive sorption of arsenate with OH groups. Solutions containing Ca tend to favour the immobilization of arsenate in a relatively broad pH range.

Jan 1, 1998

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By Stephen P. Winkelmann

The expansion of gold production in Nevada's Carlin Trend over the last few years has been staggering. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the mine engineering group at Newmont Gold. Organizational changes were implemented by the company to effectively deal with a full range of engineering problems. Specially developed computer software and its applications will be explained in this article as well as improvements in the techniques used in converting geologic resources into reserves. Scheduling procedures for the mining of multiple pits to feed multiple processing facilities will likewise be presented. Ore control procedures and current mine engineering practices are discussed. Growth at Newmont Gold Expansion of production levels at Newmont Gold Co. was brought about primarily by the economic incentive to exploit increased reserves. From 1987 to 1989, mined production increased by 260%, gold production by 238%, and manpower by 166% (Table 1). These increases came quickly and demanded

Jan 1, 1990

By Evangelos Spyridonos, Thomas Frommer, Wolfdietrich Skala, René Prissang

Operational grade modelling is a technique that uses production data to run daily updates of property models. It will enable mining engineers to use property predictions based on the most recently acquired data as support for quality control and decision making. The approach necessitates that the properties of the run- of-mine material can always be attributed to individual mining blocks or charges. The software employed must be highly reliable, because a system failure or the loss of data could seriously affect the mine's quality management. An operational grade modelling system has been developed for the Breitenau magnesite mine. It makes use of the Linear Octree Based Property Modelling system which was conceived and realised at the Free University of Berlin. This paper describes the system design and gives an account of the experiences during the first six months since system start-up.

Jan 1, 1996

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Dec 23, 2021

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988

By J. H. Jennekens

INTRODUCTION "Most people would probably agree that some degree of government control and regulation is essential in modern society, and it will likely continue as an important part of our social organization for the foreseeable future. But most of us tend to be ambivalent about it. In one situation or another we are likely to see government commitment to social benefit programs or regulatory devices either as an expanding encroachment on the freedom of the individual or as an undue interference with private enterprise or with the rules of the market place. But even where there is agreement as to the desirability of government initiatives, either in general or in a particular context, it by no means follows that there will be approval of the mechanisms or procedures used or the means of carrying them out." The above statement is taken from a 1980 Working Paper of the Law Reform Commission of Canada prepared in connection with its study of the exercise of administrative law in Canada and the practices and procedures of administrative tribunals. The Atomic Energy Control Board (AECB) is one such administrative tribunal, and as the federal nuclear regulatory authority, it is responsible for licensing the production, possession and use of nuclear materials, equipment and facilities and enforcing compliance with licence conditions governing the health, safety, security and environmental aspects of the activities involved. Although the AECB was established 35 years ago with the passage in August 1946 of the Atomic Energy Control Act, like many administrative tribunals its role and functions and the regulatory process which it applies have evolved significantly during this period. The changes which have taken place over the years reflect not only the vast scientific and technological developments which have occurred but also the marked differences between contemporary society and the social milieu of the mid-1940s. However, the basic philosophy of nuclear regulation in Canada and the underlying principles of the regulatory process have changed very little. Certainly, the process is far more open in terms of the general public, it has become appreciably more comprehensive and systematic in terms of the depth and extent of both the pre- and post-licensing technical evaluations which are conducted and the ensuing compliance program. Furthermore, it now applies to the whole of the nuclear fuel cycle as well as the industrial, agricultural and medical applications of radionuclides. Nevertheless the following fundamental principles remain unchanged: a. primary responsibility for achieving high standards of nuclear safety and environmental protection in the design, construction, commissioning and operation of nuclear facilities resides with the licensee; b. the credibility of the nuclear regulatory process depends not only upon its technical correctness and practicability, but also upon acceptance by the public-at-large of its perceived effectiveness and efficiency; c. regulatory criteria and principles should be concise, clearly stated and understandable; d. regulatory decision-making should be based upon stated criteria and principles taking into account pertinent scientific and technical facts only; e. fairness and impartiality must characterize all regulatory decision-making; f. the regulatory process should be subject to a comprehensive periodic review and evaluation to ensure that it continues to produce the desired results at justified costs. EXPLANATORY NOTES The mere statement of a set of principles is a relatively simple task. Far more difficult is the explanation of what these principles mean in practical terms. To stipulate that a licensee bears the primary responsibility for achieving and maintaining high standards of nuclear safety and environmental protection may be regarded by some as an attempt by the regulatory agency to evade the responsibilities assigned to it. However, this is not the case. It is unrealistic for anyone to claim that a licensee only complies with accepted norms of public and occupational health and safety and of environmental protection because of the fear of prosecution. The vast majority of citizens conduct their affairs in a proper manner not because there

Jan 1, 1981

By SME SME

List of 43rd ICGCM 2024 ORGANIZING COMMITTEE

Jun 25, 2024

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By J. E. Lawver, R. J. Haskin, A. Nussbaum, E. A. Laurila, W. J. Bronkala, D. M. Hopstock, J. H. Brophy, M. Wada, E. J. Tenpas, R. W. Salmi

Electrostatic separation is the selective sorting of solid species by means of utilizing forces acting on charged or polarized bodies in an electric field. Separation is effected by adjusting the electric and coacting forces, such as gravity or centrifugal force, and the time forces act on the particles, such that different species will have different trajectories at some predetermined time. Separations made in air are called electrostatic separation even though there is always some flow of current. Separations made using corona discharge devices are often called high tension separations. Separations made in liquids are termed separation by dielectrophesis if motion is due to polariza¬tion effects in nonuniform electric fields and termed electrophoresis if motion is due to free charge on species in an electric field. There are no industrial applications of mineral concentration by electropho¬resis or dielectrophesis; thus this section is limited to concentration in air. Typical Industrial Separations Typical applications of electrostatic separation are: 1) Beneficiation of ores, such as the concentration of the minerals ilmenite, rutile, zircon, apatite, asbestos, hematite, and many others. 2) Purification of foods, such as the removal of trash and rodent excrement from cereal seeds. 3) Sorting of reusable wastes, such as separating insulation from copper wire shreds. 4) Electrostatic sizing, namely, the sorting of solid particles ac¬cording to their size or shape. Table I is a partial list of industrial separations made by electrostat¬ics. The various types of electrostatic separators and the feasibility of commercial separations are most easily understood by reviewing pertinent basic electrostatic theory and the selected electrical proper¬ties of solids prior to describing the equipment and application. This is the sequence of presentation used in this section. Electrostatic Units One of the greatest sources of confusion and error is due to the multitude of units used in electrostatic literature. The system of units used throughout this section is the rationalized MKS, often called Systéme International (SI) units. In this system the mechanical units are the meter, kilogram, and the serond. The unit of force is the newton (N). This system is completed by the addition of the unit of charge, the coulomb (C). The fourth dimension, viz., the coulomb. could also be considered to be the ampere, since one ampere is the flow in a conductor of one coulomb per second. A more complete definition of the coulomb is given in Chap. 4, p. 6-11. The derived

Jan 1, 1985

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By J. Gonzales

For this paper, blending is conceived as a linear process that takes a proportion from one stockpile or location and mixes it with another proportion from another stockpile or location, with the aim of obtaining a set of attributes in the final combination that satisfies a given quality standard. A blending class is the combination of ore attributes and grade limits that should be stockpiled in order to achieve the target quality for the process Plant. Current literature considers the number of blending classes in the Open Pit Scheduling Problem as fixed; however, this paper shows how to define specific blending classes for a given deposit so that the schedule can be solved with Sequential Linear Programming. Finally, a practical application in a Peruvian copper mine is shown, involving four ore attributes: alteration code, arsenic, oxide content and copper grade. INTRODUCTION In copper ore deposits, blending for quality has not been a typical issue as it was for coal and iron ore; however, current copper deposits in the world are becoming geologically and chemically more complex than in the past and is not uncommon to have quality standards involving up to four attributes, introducing an additional complexity to the mine scheduling process [1]. In order to solve the Open Pit Scheduling Problem with multiple ore quality constraints, two assumptions are necessary [2]: - Grade constraints are defined only by specifying an upper and lower limit; - Ore attributes in stockpiles are pre-determined, i.e., the upper and/or lower grade limits defining each stockpile are already known at the time of setting the schedule. Assuming each ore attribute is classified as high, medium or low, and there are four attributes to be controlled in the target ore quality, the number of possible blending classes would be 3^4 = 81. This number is impractical to manage in Operations, and increases the complexity at the time of running the schedule; therefore, a more efficient way of classifying ore is required. Note that in practice, one blending class can be split into more than one stockpile location due to physical capacity constraints. Therefore, the number of stockpiles could even be more than 81. BLENDING CLASSES DETERMINATION For a given set of ore grades with lower and upper limits to be achieved, one has to find all feasible ore classes such that when blended, their grades will lie within those limits.

Jan 1, 2019

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By Victor F. Hollister

Skam deposits considered as porphyry copper deposits have been classified into three basic prospecting models: (I) the skam deposit associated with a mineralized intrusive (Pima-Mission), (2) the deposit associated with a barren igneous stock (Ertsberg), and (3) mineralized rock that seems to have no clear association with apluton (Phoenix). Pima-Mission, Christmas, and many other copper-bearing skarns developed in carbonate sequences near mineralized intrusives form an important part of the deposit. Historically, copper derived from the mineralized intrusion accounts for less than half of the metal produced by most porphyry mines, as most mineralization occurs in the intruded rocks. Skam mineralization is an important part of wall-rock metal deposition, because carbonate sequences are preferentially replaced by sulfide and skarn minerals. Exploration for skam mineralization is an important phase of porphyry copper exploration. Impure carbonate beds can become better host rocks for skam deposits than pure carbonates, and these in particular should be included in porphyry-exploration programs if the impure strata are cut by the stock. Skam deposits can also form near stocks that are barren of sulfide. In this model, the two best ore guides are strata favorable for mineralization (usually impure carbonate beds) and the intrusive contact. Faults can also act as important ore controls. Some skarn deposits form that have no clear genetic connection with a stock, although intrusive rocks are known in the district. In such cases, the best ore guides are strata and district-wide faulting. Dikes and sills are also common and mineralization can locally prefer their contacts even though the igneous rocks are barren. Skam minerals are influenced by the chemical composition of the carbonate. Forsterite, brucite, tremolite, and talc are common in skams developed in dolomitic beds. Skams derived from calcic beds often contain wollastonite, calcite, stilbite, or idocrase. Diopside, however, is a common accompaniment of copper sulfide in skam regardless of the original composition of the carbonates. Tremolite and possibly other amphiboles and chlorite can occur significantly in the zinc-lead portion of skams. Gamets occur in magnetite, copper, and zinc-lead zones of skams, but are not as diagnostic as diopside for the copper zone or tremolite for the zinc-lead zone. A general desciption of skam-deposit mineralogy can be used to construct prospecting models of porphyry copper skams. An abstract of such a description follows.

Jan 1, 1991

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By David Hurth

JOHN HAMRIC: Our next topic leader is David Huth, superintendent of sulfuric power generation, DAP, and shipping for IMC-Agrico, Nichols Plant, Mulberry, Florida. With a title like that it's no wonder he believes in empowerment. His topic today is "The Triumphs and Pitfalls of Using Empowerment Techniques." DAVID HUTH: Empowerment and its benefits are a desirable alternative to the traditional management structure. The difference between the two is the amount of decision- making authority and responsibility given to individuals by a supervisor. Just what is empowerment and how does it work? Empowerment is relinquishing to individuals the authority and responsibility to make daily decisions. Can everyone be empowered? What if they make a wrong decision? Will I empower myself out of a job? These are questions that all managers have when they hear the word empowerment. In today's fast-paced and high-pressure business environment, the old way of managing people must be replaced with a new approach. No longer can we, as managers, make all the decisions. The increased work loads due to downsizing, consolidation, and synergies have stretched us too thin. What about our employees? How can we motivate them into the high-performance teams that our companies are demanding? What possibly could satisfy both these issues? The solution to these problems can be solved with the power of employee empowerment. Employee empowerment will not only lessen the load on managers but will build teamwork, motivation, and pride into the employees who work for the managers who use it. American business was rudely awakened in the early 1980s when the Japanese companies not only caught up to American companies but literally flew by them. America was fat, dumb, and happy after World War II. Why wouldn't they be? They had all the factories. Everyone else had to rebuild. So for 40 years American business lounged in the limelight of very little true competition. But times change. Unfortunately, American business did not. Now the cry to perform in the new global economy has come down from the corporate boardrooms. Down through the ranks it has been felt. Guess who is supposed to make it work? But where are all those people who are going to make this rejuvenation and corporate renaissance possible? Many of them are gone-lost in downsizing, synergies, and rightsizings

Jan 1, 1998

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

NTRODUCTION Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for pre¬dicting the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface move¬ment data, a relatively large portion of the subsidence data col¬lected could not provide information other than surface movement. In a paper by Luo and Peng (1992), the sources and magnitude of errors in the measured surface movements using an electronic total station in subsidence survey are discussed. If the errors in the measured surface movement components are left untreated before calculation for deformation indices (i.e., slope, strain and curva¬ture), the errors will be carried over to the deformation indices and enlarged if improper numerical procedures are used in the calcu¬lation. It should be noticed that in protecting structures affected by ground subsidence, accurate surface deformation indices are much more important than surface movement. In order to improve the accuracy of the collected surface movement data and the calcu¬lated deformation indices, a number of numerical procedures are also proposed in the same paper. The proposed techniques include: a data smoothing technique for data pre-processing; and a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data. DATA SMOOTHING Because of various factors, the measured surface movement data always contain errors, small or large. In order to better utilize the collected data, a data smoothing method is proposed to correct the errors in the measured movement data. The method uses the same concept as the influence function method (e.g., Knothe, 1957) on which many existing subsidence prediction methods are based. The data smoothing method makes necessary corrections on the measured movement for the point of interest according to not only the measured movement at this point but also those at the surrounding points. The contribution of a surrounding point in making the correction for the point of interest is inversely propor¬tional, in exponential form, to the distance between them. The new magnitude of a movement component at the point of interest (Zi*) is calculated by

Jan 1, 1992